AUX GEELY FC 2008 Workshop Manual

Engine mechanismEngine assemblyInspection1. Check coolant.
2. Check engine oil.
3. Check battery.
4. Check air filter assembly.
5. Check spark plug [4G18-3705113].
6. Check drive belt [4G18-1307107].Hint: do not check belt tension, because automatic tensioner is applied.7. Check ignition timing.(a) Warm up engine.
(b) Connect timing lamp to engine.
(c) Check ignition timing at idle speed.
Ignition timing: before top dead center Note: when checking ignition timing, place
transmission at neutral position.
Hint: After run the engine for 5 seconds with rotating
speed of 1000-1300rpm, check the engine could
recover to idle running.8. Check engine idle speed.(a) Warm up engine and run it at idle speed.
(b) Read engine rotating number in data flow with diagnostic instrument.
(c) Check idle speed.
Idle speed: about 750-850rpm
Notes:When checking idle speed, place cooling fan at OFF position.Turn off all auxiliary devices and air conditioner.Engine mechanism - Engine assemblyK-line 26

Steering column--Steering systemSteering column--Steering system
Steering column--Steering systemSteering column--Steering systemSteering column--Steering system
Steering column
Steering system
Note
1. Notes that are necessary for steering system:
(a) It is necessary to change parts correctly, for they will influence the performance of steering system to
make running danger.
2. Notes that are necessary for SRS airbag:
(a) MR7180 assembles with SRS (auxiliary protection system) such as safety airbag at the side of driver
and safety airbag at the side of passenger.
Maintenance does not accord with correct repair step, this might incur SRS explodes suddenly in
repair term to make heavy accident. Before repairing auxiliary protection system (including
disassembling, assembling, check or change parts), it is necessary to read the notes in SRS chapter
(auxiliary protection system).
Malfunction phenomenon table
Following table could help you find the reason of malfunction. And the number in table is only used for indicat-
ing possible preferred sequence. Please check each part by sequence, if necessary, change this part.
Malfunction phenomenon Possible malfunction part Referred page
1.Tyre (tyre pressure is wrong). 109
2.Power steering oil level (low). 200
3.Driving belt (loose). -
4.Wheel alignment (wrong). 87
Steering is heavy 5.Steering system joint (abraded). -
6.Lower control arm ball joint (abraded). 99
7.Steering column (bent). -
8.Power steering oil pump. 203
9.Power steering gear. 205
1.Tyre (tyre pressure is wrong). 109
Return is bad 2.Wheel alignment (wrong). 87
3.Steering column (bent). -
4.Power steering gear. 205
1.Steering system joint (abraded). -
2.Lower control arm ball joint (abraded). 99
Clearance is too big. 3.Middle shaft, sliding fork (abraded). -
4.Front wheel bearing (abraded). 123
5.Power steering gear. 205
1.Power steering oil level (low). 200
2.Steering system joint (abraded). -
Abnormal noise
3.Power steering oil pump. 203
4.Power steering gear. 205
 192 

Power steering--Poser steering system
Power steering
Power steering system
Note
1. Notes for steering system:
It is necessary to change parts correctly, for they will influence the performance of steering system to incur
running danger.
2. Notes for SRS airbag system
MR7180 equips with SRS (auxiliary protection system), such as safety airbag at the side of driver and
safety airbag at the side of passenger, if repairment does not accord with correct sequence, it might incur
SRS explodes suddenly in repairing term to make heavy accident. Before repairing (including disassem-
bling or assembling, checking or changing parts), it is necessary to read the notes in chapter SRS (auxiliary
protection system) carefully.
 198 

Power steering--Power steering gear assembly
(b) Disassemble the screw and disconnect the fixed clamp of
in-out oil pipe assembly of power steering gear.
12. Disassemble linking lever assembly of front stabi-
lizer bar [64000097].
(a) Use socket head wrench (5mm) to fix bolt, then disas-
semble screw cap.
(b) Disassemble the left linking lever of front stabilizer liking
lever assembly.
Hint: disassemble the other with same method.
13. Disassemble the coupling bolt and nut of left/right
lower control arm ball head and control arm.
Disassemble one bolt and two nuts, and disassemble control
arm from left steering knuckle.
Hint: disassemble the other with same method.
14. Disassemble engine cover assembly
15. Support engine assembly.
16. Disassemble auxiliary automobile bracket assem-
bly [64000087]
(a) Disassemble two bolts, then disassemble side rail from
right front engine suspension.
(b) Disassemble two bolts, then disassemble carling from au-
tomobile body.
(c) Disassemble the bolt and three nuts, then disassemble
engine rear suspension from auxiliary automobile bracket.
(d) Use gearbox jack to support auxiliary automobile bracket.
(e) Disassemble four bolts and auxiliary automobile bracket
assembly with steering gear.
17. Disassemble exterior dust-proof cover of steering
column.
 206 

Power steering--Power steering gear assembly
34. Assemble steering middle shaft.
(a) Align the mark of steering middle shaft and steering small
gear shaft.
(b) Assemble the bolt.
Torque: 35 N
x xx x
xm
35. Assemble exterior dustproof cover of steering
column.
36. Assemble auxiliary bracket assembly (64000087).
(a) Use special tool to align the right side of auxiliary bracket
with the hole of body, then lock the A bolt and B bolt
temporarily.
(b) Use special tool to align the left side of auxiliary bracket
with the hole of body, then lock the A bolt and B bolt
temporarily.
(c) Use special tool to align the left side of auxiliary bracket
with the hole of body, then lock the A bolt and B bolt.
Torque:
A bolt: 157 ± 10 N
x xx x
xm
B bolt: 113 ± 10 N
x xx x
xm
(d) Use special tool to align the right side of auxiliary bracket
with the hole of body, then lock the A bolt and B bolt.
Torque:
A bolt: 157 ± 10 N
x xx x
xm
B bolt: 113 ± 10 N
x xx x
xm
(e) After connecting with engine with one bolt and three screw
caps, hang it to auxiliary bracket.
Torque: 52 N.m ± 5 N
x xx x
xm
(f) Assemble carling to body with two bolts.
Torque: 39 ± 3 N
x xx x
xm
(g) Assemble the front suspension of engine to carling with
two screw caps.
Torque: 52 ± 5 N
x xx x
xm
Align the mark
Special
tool
Special tool
 210 

Change
1. Reclaim HFC-134a (R134a)
(a) Turn A/C switch to ON.
(b) Keep the engine speed at 1000 rpm, and rotate cooling compressor for 5 to 6 minutes to make
refrigerant cycle, this could collect the Refrigerant oil in each part in cooling compressor as possible.
(c) Extinguish the engine.
(d) Drain the refrigerant.
2. Fill refrigerant
(a) Use vacuum pump to take out vacuum.
(b) Fill the refrigerant HFC-134a (R134a)
Standard quantity: 660 ± 10g
3. Heat the engine
4. Check whether the refrigerant leaks.
Air conditioner--Refrigerant
 221 
Bubble
disappearing
pointToo much filling refrigerant Increase 100g Filling quantity of refrigerant
Pressure at
the high
pressure side
Refrigerant quantity
Auxiliary condenser system
Applicable
filling scope

15. Disassemble central ventilation orifice assembly of panel [68010012].
16. Disassemble right storage box assembly of lower panel [68010008].
17. Disassemble inner trim board assembly of right front column [68010017].
18. Disassemble inner trim board assembly of left front column [68010014].
19. Disconnect the joint of safety airbag assembly at the side of passenger.
20. Disassemble upper panel assembly [6801004].
21. Disassemble upper/lower trim board of steering pipe [64000128/64000129].
22. Disassemble left combination switch assembly [67000078].
23. Disassemble right combination switch assembly [67000079].
24. Disassemble air spring assembly of right storage box [68000082].
25. Disassemble decoration panel assembly of shift organization [68000076].
26. Disassemble air conditioner control panel assembly [67000148].
27. Disassemble the assemble bracket of CD machine.
28. Disassemble ventilation pipe assembly of evaporator [67000149].
29. Disassemble air conditioner control assembly.
30. Disassemble parking brake lever hole cover.
31. Disassemble auxiliary panel assembly.
32. Disassemble step trim board of right front door [68010021].
33. Disassemble step trim board of left front door [68010020].
34. Disassemble lower inner trim board of right defender [68010016].
35. Disassemble lower inner trim board of left defender [68010015].
36. Disassemble central linking board of lower panel [68010006].
37. Disassemble lower panel assembly [68010005].
38. Disconnect steering column assembly [64000122].
(a) Disassemble three bolts.
(b) Disassemble steering column from panel framework body.
Air conditioner--Air conditioner central heating core assembly
 228 

Supplemental restraint system--Disassemble and assemble
Disassemble and assemble
Electronic control unit of safety airbag (ECU)
1. Note (referring to chapter 1)
2. Disassembling sequence:
(1) Disassemble the cover board at the side of central channel (or disassemble auxiliary panel).
(2) Disassemble the connector connecting with safety airbag ECU.
(3) Disassemble the ECU.
3. Assembling sequence
(1) Check the ECU assembly, and make arrow direction on hint card point to running direction of automobile.
(2) Assemble the connector connecting with safety airbag ECU, the connector should be locked firmly (if
you hear a light sound “KA” when press the connector, this shows it has been locked).
a. Fix the special bolt used by controller assembly on assembling position of central channel, and
confirm it has been assembled firmly.
b. Assemble the cover board at the side of central channel (or assemble auxiliary panel).
c. Connect the cathode of battery.
4. Main notes of assembling operation:
(1) When assembling ECU assembly, pay attention to that ECU assembly could not be impacted.
(2) Inspection after the assembling
a. Set the ignition switch at ON position.
b. Indicating light illuminates at 7 second, and continues to extinguish.
c. If it does not extinguish, it is necessary to check and remove malfunction.
Note: if ECU could not be assembled correctly, safety airbag will not work normally.
5. Inspection: referring to chapter 2.
6. Removing malfunction: referring to chapter 3.
3. Place the steering wheel and front wheels correctly
and make them face the front, and take out ignition
switch key, then do not operate it in 60 seconds af-
ter disassembling the cathode of battery.
4. Disassemble safety airbag assembly at the side of
driver:
(1) Guarantee the wheels face the front.
(2) Use 5s hexagon socket-head wrench to loosen the two plan-
etary bolts.
(3) Pull out the safety airbag assembly at the side of driver
from upside of steering wheel.
Safety airbag assembly at the side of driver
1. Note (referring to chapter 1).
2. Use the flash or malfunction diagnostic tool to test malfunction (referring to chapter 1
and 3).
 261 

Wiper and cleaner--Wiper generator
Fixing clasp
Fixing
claw
Wiper generator
Change
1. Disassemble wiper arm cap.
2. Disassemble auxiliary wiper arm assembly
[68000059]
Disassemble screw cap and auxiliary wiper arm assembly.
3. Disassemble main wiper arm assembly [68000057]
Disassemble screw cap and main wiper arm assembly.
4. Disassemble generator cap to fire barrier seal.
Separate eight fixed buckles to disassemble the seal from gen-
erator cap to fire barrier.
5. Disassemble ventilation cover on passenger side.
Disassemble five fixed jaws so as to disassemble ventilation
cover on passenger side.
6. Disassemble ventilation cover on driver side.
Disassemble five fixed jaw so as to disassemble ventilation
cover on driver side.
7. Disassemble wiper connecting rod assembly
[68000053]
(a) Disassemble the joint.
(b) Disassemble the bolt.
(c) Slide wiper connecting rod assembly to passenger side to
separate meshing of rubber pin so as to disassemble wiper
connecting nod.
Fixing
claw
 303 
Pin

Panel/combination instrument-- panel
L
4 Fixing
clasp
3 Fixing
clasp
Fixing
clamp
25. Disassemble parking brake hole cover.
Use screw driver to unclench four fixing clamps, then disas-
semble parking brake hole cover.
Hint: before using screw driver, it is necessary to wrap its
needled top with adhesive tape.
26. Disassemble auxiliary panel assembly [68010002]
(a) Disassemble two L bolts, two C bolts and auxiliary panel
assembly.
27. Disassemble right front door pedal trim board
[68010021]
Use screw driver to unclench three fixing clamps, then disas-
semble right front door pedal trim board.
Hint: before using screw driver, it is necessary to wrap its
needled top with adhesive tape.
28. Disassemble left front door pedal trim board
[68010020]
29. Disassemble lower inner trim board of right de-
fender [68010016]
(a) Disassemble plastic nuts of lower inner trim board of right
defender.
(b) Unclench fixing clamp, then disassemble lower inner trim
board of right defender liking that shown in figure.
30. Disassemble lower inner trim board of left defender
[68010015]
31. Disassemble connecting board at the middle of
panel [68010006]
(a) Use screw driver to unclench four fixing clamps, then open
the connecting board at the middle of panel.
Hint: before using screw driver, it is necessary to wrap
its needled top with adhesive tape.
(b) Disassemble connecting board at the middle of panel.
 344