change wheel GEELY FC 2008 User Guide

Left rear shaft hub boltChange1. Disassemble rear wheels
2. Disassemble left rear brake caliper assembleDisassemble two bolts and take down brake caliper.3. Disassemble left rear brake assembly [64000137]
4. Disassemble left rear shaft hub bolt(a) Screw the shaft to the position in figure, then use special
tool to disassemble shaft hub bolt.
Note: shaft hub bolt should be screwed to the position
in figure, or you could not change shaft hub bolt.
(b) Use special tool and screw driver to disassemble shaft hub
bolt.5. Assemble left rear shaft hub bolt(a) Liking that shown in figure, assemble new gasket and screw
cap on new shaft hub bolt.
(b) Use screw driver to fix and lock screw cap to make the bolt
enter hole.6. Assemble left rear brake assembly [64000137]
7. Assemble left rear brake branch pump assemblyUse two bolts to assemble rear brake branch pump assembly.
Torque: 46 ± 5 N
⋅ ⋅⋅ ⋅
⋅m8. Assemble rear wheelsTorque: 103 ± 10 N
⋅ ⋅⋅ ⋅
⋅mDrive shaft--Left rear shaft hub bolt131

Brake--Front brake assembly23.Assemble dustproof cover of branch pump..(a) After spreading lithium soap base glycol lubricating grease
on new dustproof cover of branch pump, assembling it in
brake branch pump.
Hint: dustproof cover should be assembled in branch
pump firmly.
(b) Use wrench to assemble fixing loop.
Note: do not damage dustproof cover.24. Assemble brake branch pump bracket.Use two bolts to assemble brake branch pump bracket.
Torque: 106
± ±± ±
± 10 N
⋅ ⋅⋅ ⋅
⋅m25. Assemble dustproof cover of brake branch pump
bracket.(a) Spread lithium soap base glycol lubricating grease on new
dustproof cover.
(b) Assemble two dustproof covers in front brake branch pump
bracket.26. Assemble sliding pin of front brake branch pump.(a) Spread lithium soap base glycol lubricating grease on the
surface of sliding part and sliding pin.
(b) Assemble two sliding pins in front brake branch pump
bracket.27. Assemble support sheet of brake block.143 28. Assemble brake block.Note: when changing brake block, muffle gasket should be changed with brake block at the same
time.
(a) Spread brake lubricating grease on both sides of every muffle gasket.
(b) Assemble muffle gasket on every brake block.
(c) When assembling inner brake block, abrasion indicator should face the upside.
Note: do not attach oil dirt or lubricating grease on the surface of brake block and brake disk.29. Assemble brake branch pump assembly.(a) Use two bolts to assemble brake branch pump.
Torque: 34
± ±± ±
± 3N
⋅ ⋅⋅ ⋅
⋅m
(b) Use joint bolt to assemble new gasket and brake hose.
Torque: 30
± ±± ±
± 3N
⋅ ⋅⋅ ⋅
⋅m
Hint: Gasket has two types: two sheets type and one type.
Bracket soft pipe should be assembled in localizing hole of branch pump firmly.30. Add brake liquid in storage tank.
31. Discharge the air in brake main pump.
32. Discharge the air in brake pipeline.
33. Check the liquid level of storage tank.
34. Check whether the brake liquid leaks.
35. Assemble front wheels.Torque: 103
± ±± ±
± 10 N
⋅ ⋅⋅ ⋅
⋅m

Brake--Rear brake assembly24. Assemble rear brake block.Note: when changing brake block, the inside of muffle gasket should be changed together.
(a) When assembling muffle gasket on every brake block, it is necessary to spread brake lubricating
grease on the inside of muffle gasket.
(b) When assembling inner brake block, abrasion indicator should face upside.
Note: do not attach any oil dirt or lubricating grease on the surface of brake block and brake
disk.
(c) Assemble two guide pins of brake block.
(d) Assemble fixing clamp of anti-abrasion spring.25. Add brake liquid in storage tank.
26. Discharge the air in brake main pump (referring to page 135).
27. Discharge the air in brake pipeline (referring to page 135).
28. Check the liquid level in storage tank.
29. Check whether brake liquid leaks.
30. Assemble rear wheels.Torque: 103
± ±± ±
± 10N
⋅ ⋅⋅ ⋅
⋅m147

Hydraulic control unit (equipping with ABS)Inspection on automobile1. Connect handle tester(a) Connect handle tester to DLC3.
(b) Start the engine and make it run at idling speed.
(c) Handle tester should choose “Active test” module.
Hint: details could refer to operating instruction for handle tester.2. Check the function of hydraulic .(a) Start the motor relay, and check hydraulic motor should have working sound.
(b) Stop the motor relay.
(c) Step brake pedal for 15 minutes, and check brake pedal should not be stepped down.
(d) Start the motor relay, and check brake pedal should not have any pulse.
Note: Time when motor relay locates ON could not exceed 5 seconds, when it is necessary to
operate continually, interval time should be over 20 seconds.
(e) Stop the motor relay and release brake pedal.3. Check the function of right front wheel.Note: forbid making electromagnetic valve be ON in following situations.
(a) Make following operation when brake pedal is stepped down.
(b) Make electromagnetic valve SFRH and SFRR be ON at the same time, and check the brake pedal
should not be stepped down.
Note: Time when motor relay locates ON could not exceed 5 seconds, when it is necessary to
operate continually, interval time should be over 20 seconds.
(c) Make electromagnetic valve SFRH and SFRR be OFF at the same time, and check the brake pedal
should be able to be stepped down.
(d) Make electromagnetic valve SFRH and SFRR be ON at the same time, and check whether the brake
pedal could return.
Note: Time when motor relay locates ON could not exceed 5 seconds, when it is necessary to
operate continually, interval time should be over 20 seconds.
(e) Make motor relay be OFF and release brake pedal.4. Check the function of other wheels.Check the electromagnetic valves of other wheels by same procedure.
Hint:
Left front wheel: SFLH,SFLR
Right rear wheel: SRRH,SRRR
Left rear wheel: SRLH, SRLRChange1. Discharge brake liquid.Note: do not leave brake liquid on paint surface of automobile body, if having, wash it cleanly.2. Disassemble right front wheel.Brake--Hydraulic pressure control unit148

Brake--Speed sensor of front wheelSpeed sensor of front wheelChangeHint: the process for changing right side is same as the
left side.1. Disassemble front wheels.
2. Disassemble gasket of left front wing.
3. Disassemble speed sensor of left front wheel.(a) Disassemble resinous clamp and speed sensor wiring har-
ness from fixing clamp of automobile body.
(b) Disassemble the sensor joint.
(c) Disassemble two bolts of fixing clamp of sensor wiring har-
ness from automobile body and absorber.
(d) Disassemble bolt and left front sensor.
Note: do not attach any sundries on top of sensor.4. Assemble speed sensor of left front wheel.(a) Use bolt to assemble left front sensor.
Torque: 8.0 N
⋅ ⋅⋅ ⋅
⋅m
Note: do not attach any sundries on top of sensor.
(b) Use two bolts to assemble fixing clamp of sensor wiring
harness on automobile body and absorber.
Bolt A: 9.0 N
⋅ ⋅⋅ ⋅
⋅m
Bolt B: 29 N
⋅ ⋅⋅ ⋅
⋅m
(c) Connect the joint of speed sensor.
(d) Connect resinous clamp and speed sensor wiring harness
on automobile body and fixing clamp.5. Assemble gasket of left front wheel wing.
6. Assemble front wheels.Torque: 103
± ±± ±
± 10 N
⋅ ⋅⋅ ⋅
⋅m7. Check the signal of ABS speed sensor.151

Brake--Speed sensor of rear wheelsSpeed sensor of rear wheelsChangeHint: the process for changing right side is same as the
left side.1. Disassemble rear wheels.
2. Disassemble wiring harness of speed sensor of rear
wheel.Disassemble the joint of speed sensor of rear wheel.3. Disassemble left rear disk brake branch pump
assembly.
4. Disassemble rear brake disk.
5. Disassemble left rear shaft hub and bearing assem-
bly (referring to page 129).
6. Disassemble speed sensor of rear wheel.(a) Fix rear shaft hub on pliers with soft gasket.
Note: when changing shaft hub assembly, it is neces-
sary to shake intensively to make it break off.
(b) Use punch pin and hammer to knock out two pins.
(c) Use special tool and two bolts (M12*1.5) to disassemble
speed sensor of rear wheel from rear shaft hub.
Note:zIf sensor stator is damaged, change the shaft hub
assembly.zDo not scratch the surface of shaft hub and speed
sensor.7. Assemble speed sensor of rear wheels.(a) Wash contacting surface of rear shaft hub and new speed
sensor of rear wheels.
(b) When sensor is assembled in shaft hub, it is necessary
to assemble sensor joint facing lower position of
automobile.Special
tool
Special tool Bolt
Bolt152

Parking brakeParking brake systemMalfunction phenomenon tableUse following table to find the reason of malfunction, the number in table indicates the preferred se-
quence of possible reason. Please check each part by sequence, if necessary, change this part.Parking brake--Parking brake systemAdjustment1. Disassemble rear wheels
2. Adjust the clearance of parking brake shoe
3. Assemble rear wheelsTorque: 103
± ±± ±
± 10 N
⋅ ⋅⋅ ⋅
⋅m4. Check the travel of parking brake handle.Pull up the parking brake handle and calculate the sound num-
ber of handle.
When parking brake handle locates 196N: 6-9 sounds.5. Adjust the travel of parking brake handle(a) Disassemble upper trim board of central box.
(b) Disassemble central box.
(c) Release locking screw cap, then rotate adjusting screw cap
until handle travel accords with the specification.
(d) Tighten locking screw cap.
Torque: 5.0 N
⋅ ⋅⋅ ⋅
⋅m
(e) Assemble central box.
(f) Assemble trim board on central box.Malfunction phenomenon Possible malfunction part Reference page
1. Travel of parking brake handle (adjusted badly). 154
2. Pull cable of parking brake (attached).156, 158
Brake lag 3. Clearance of parking brake shoe (adjusted badly). 161
4. Friction plate of parking brake shoe (damaged or distorted). 161
5. Tension or return spring (damaged). 161Lock the screw cap
Adjust the
screw cap154

Parking rear brake pull cable assembly
Change
Hint: the changing procedure for left rear brake pull cable is same as parking right rear brake
pull cable.
1. Disassemble rear wheels.
2. Disassemble rear brake disk brake branch pump bracket assembly(LH).
3. Disassemble brake disk.
4. Disassemble support lever of parking brake shoe (LH).
5. Disassemble adjustor of parking brake shoe.
6. Disassemble parking brake inner shoe assembly (LH).
7. Disassemble parking brake exterior shoe assembly (LH).
8. Disassemble parking brake shoe lever (LH).
9. Disassemble left rear brake pull cable assembly.
Disassemble the bolt and parking left rear brake pull cable assembly from brake back board.
10. Disassemble front bottom board bracket.
11. Disassemble front part exhaust pipe.
12. Disassemble heat insulation board.
13. Disassemble parking left rear brake pull cable assembly.
Parking brake--Parking rear brake pull cable assembly
(a) Disassemble fixing clamp of rear wheel speed sensor wiring
harness.
(b) Disassemble four bolts and parking left rear brake pull cable
from automobile.
(c) Disassemble left rear brake pull cable from parking brake
balancer, then disassemble parking left rear brake pull cable.
14. Assemble parking left rear brake pull cable
assembly.
(a) Connect parking left rear brake pull cable on parking brake
pull cable balancer.
(b) Assemble parking left rear brake pull cable with four bolts.
Torque: 5.4 N
⋅ ⋅⋅ ⋅
⋅m
(c) Connect resinous clamp of speed sensor wiring harness of
 158 

Steering column--Steering systemSteering column--Steering system
Steering column--Steering systemSteering column--Steering systemSteering column--Steering system
Steering column
Steering system
Note
1. Notes that are necessary for steering system:
(a) It is necessary to change parts correctly, for they will influence the performance of steering system to
make running danger.
2. Notes that are necessary for SRS airbag:
(a) MR7180 assembles with SRS (auxiliary protection system) such as safety airbag at the side of driver
and safety airbag at the side of passenger.
Maintenance does not accord with correct repair step, this might incur SRS explodes suddenly in
repair term to make heavy accident. Before repairing auxiliary protection system (including
disassembling, assembling, check or change parts), it is necessary to read the notes in SRS chapter
(auxiliary protection system).
Malfunction phenomenon table
Following table could help you find the reason of malfunction. And the number in table is only used for indicat-
ing possible preferred sequence. Please check each part by sequence, if necessary, change this part.
Malfunction phenomenon Possible malfunction part Referred page
1.Tyre (tyre pressure is wrong). 109
2.Power steering oil level (low). 200
3.Driving belt (loose). -
4.Wheel alignment (wrong). 87
Steering is heavy 5.Steering system joint (abraded). -
6.Lower control arm ball joint (abraded). 99
7.Steering column (bent). -
8.Power steering oil pump. 203
9.Power steering gear. 205
1.Tyre (tyre pressure is wrong). 109
Return is bad 2.Wheel alignment (wrong). 87
3.Steering column (bent). -
4.Power steering gear. 205
1.Steering system joint (abraded). -
2.Lower control arm ball joint (abraded). 99
Clearance is too big. 3.Middle shaft, sliding fork (abraded). -
4.Front wheel bearing (abraded). 123
5.Power steering gear. 205
1.Power steering oil level (low). 200
2.Steering system joint (abraded). -
Abnormal noise
3.Power steering oil pump. 203
4.Power steering gear. 205
 192 

Steering column--Steering systemSteering column--Steering system
Steering column--Steering systemSteering column--Steering systemSteering column--Steering system
Align the mark
(b) Align the mark on sliding yoke and middle shaft.
(c) Assemble B bolt and tighten A bolt.
Torque: 35 ± 3 Nxm
Hint:When changing new sliding yoke, it is neces-
sary to adjust the front wheel at the front, and
make the bolt hole surface of sliding yoke face
the back (liking that shown in figure), then as-
semble the bolt.
21. Adjust front wheel at the front.
22. Assemble helix cable assembly (equipping with
SRS) [67000121]
23. Put the helix cable assembly at central position
(equipping with SRS)
(a) Check whether the front wheel faces the front.
(b) Turn helix cable counter-clockwise with hand until it could
not turn.
(c) Then turn helix cable 2.5 clockwise and align the mark.
Hint:helix cable could turn left or right from central
position for 2.5 rounds.
24. Assemble steering wheel assembly [67010001]
(a) Align the mark on steering wheel and main shaft assembly.
(b) Assemble the fixed screw cap of steering wheel.
(c) Connect the joint.
25. Assemble safety airbag assembly at the side of driver [67010011]
Warning:
zForbid using SRS parts on other automobiles, when changing any part, it is necessary to use new
product.
zIf safety airbag assembly at the side of driver once dropped or exterior shell and joint has crack,
concave or other distortions, it is necessary to change with new product.
zWhen assembling the airbag assemble at the side of driver, it is necessary to pay attention to airbag
wiring harness could not interrupt other parts or be clamped by other parts.
(a) Connect the end.
(b) Connect the joint of airbag.
(c) After assembling the safety airbag assembly at the side
of driver, insure planetary screw of concave slot contacts
with screw shell.
(d) Use planetary screwdriver to tighten two screws.
Torque: 8.8 Nxm
26. Check the central point of steering wheel
27. Check SRS warning light (equipping with SRS)
Align the
mark
 197 
planetary
screws screw shell