change wheel GEELY FC 2008 Owner's Manual

Power steering--Poser steering system
Malfunction phenomenon Possible malfunction part Reference page
1.Tyre (tyre pressure is wrong).109
2.
Power steering oil level (low).200
3.
Driving belt (loose).-
4.
Wheel alignment(wrong).87
Steering is heavy5.Steering system joint (abraded).-
6.
Lower control arm ball head (abraded).99
7.
Steering column (bent).-
8.
Power steering oil pump203
9.
Power steering gear205
1.
Tyre (tyre pressure is wrong).109
Return is bad2.Wheel alignment (wrong)87
3.
Steering column (bent)-
4.
Power steering gear205
1.
Steering system joint (abraded)-
2.
Lower control arm ball head (abraded)99
Clearance is too big3.Middle shaft, sliding fork (abraded)-
4.
Front wheel bearing (abraded)123
5.
Power steering gear205
1.
Power steering oil level (low)200
Abnormal noise2.Power steering joint (abraded)-
3.
Power steering oil pump203
4.
Power steering gear205
Malfunction phenomenon table
Use following table to help you find the reason of malfunction, the number in table only show the possible
preference sequence of malfunction, please check each part by sequence, if necessary, change this part.
 199 

Power steering--Poser steering system
Inspection on automobile
1. Check driving belt
(a) Check whether the belt has been abraded too much with eyes, and rope is broken.
If finding any defect, change the driving belt.
Hint: Some light crack at the side of belt rib could be approved, but if belt has any crack from
its rib, it is necessary to change.
2. Exhaust air of power steering system
(a) Check the oil level.
(b) Lift up automobile body, and support it with bracket.
(c) Turn steering wheel.
(1) Turn steering wheel slowly from left and right to bottom for several times when engine extinguishes.
(d) Lay down the automobile.
(e) Start the engine to make it run at idling speed for several minutes.
(f) Rotate steering wheel.
(1) Keep engine at idling speed, and turn the steering wheel from left or right to bottom and keep this
state for 2-3 seconds, then turn it to the other direction for 2-3 seconds.
(2) Repeat (1) for several times.
(g) Engine extinguishes.
(h) Check whether there is any foam or emulsification
phenomenon.
If there is any foam or emulsification phenomenon and
it is necessary to exhaust air second time, it is necessary
to check whether the system has any leakage.
(i) Check the oil level.
3. Check the oil level
(a) Keep automobile horizontal.
(b) Extinguish the engine, and check the oil level of oil stor-
age tank.
If oil level is too low, add oil.
Power steering oil: automatic transmission oil
DEXRON’’ II or III
Hint: check whether the oil level is in the HOT mark
scope of oil storage tank, if oil is cool, check the
oil level is in COLD mark scope.
(c) Start the engine, and keep it at idling speed.
(d) Turn steering wheel from left bottom to right bottom for
several times to make oil temperature increase.
Oil temperature: 80°C
Normal Abnormal
 200 
Normal Abnormal

Power steering--Power steering gear assembly
29. Assemble steering No.2 dust-proof cover.
(a) Insure steering gear hole is not plugged by lubricating
grease.
Hint: if hole is plugged, the pressure in dust-proof
cover when steering wheel turns after combin-
ing will change.
(b) Assemble dust-proof cover, fixed clamp and new iron wire.
Note: do no t hurt or bend dust-proof cover.
(c) After coiling dust-proof cover with iron wire for two circles,
turn it for several circles to fix it.
(d) Liking that shown in figure, bend iron wire to rotating di-
rection to prevent it from hurting dust-proof cover.
Hint: assemble the other side with same method.
30. Assemble No.1 dust-proof cover of steering gear.
31. Assemble left ball head of transversal lever .
(a) Screw locking cap and transversal lever ball head in gear
terminal lever until aligning the mark.
(b) After adjusting front wiring harness, tighten the screw cap
(referring to page 80).
Torque: 74 ± 5 N
xm
Hint: assemble the other side with same method.
32. Assemble right ball head of transversal lever .
33. Assemble power steering gear assembly [64000133].
(a) Assemble power steering gear assembly on beam with
four bolts.
Torque: 58 N
xm
 209 
Align the mark

Supplemental restraint system--Note
Note:
zWhen making repair, please make malfunction diagnosis by the flash light and malfunction diagnosing device
according with the method regulated in this operation manual at first, at the same time, it is necessary to check
whether there is any malfunction code before disassembling battery wire.
zForbid disassembling or repairing at any non-appointment repair station
zDo not assemble any safety lever or bumper at the front of automobile, this will influence the performance of this
airbag.
zPeople for repairing, disassembling and assembling should be trained specially.
zWhen disassembling steering wheel assembly, it is necessary to make steering wheel right, only this could disas-
semble steering wheel assembly and make helix cable locate correct position, or it will damage helix cable assembly.
zECU matches with the technical parameter of electric system, forbid using the SRS parts of other automobiles, at
the same time, it is necessary to use new product to replace any part.
zWhen repairing automobile (especially electric welding), it is necessary to close key switch, and it is best to cut off
the anode of battery.
zAfter unfolding airbag, safety airbag assembly and helix cable assembly should be changed completely.
zWhen disassembling or carrying airbag assembly, trim cover should face the upside; safety airbag assembly
could not superpose directly to avoid make wrong explosion and make any accident.
zThe inner malfunction of controller (ECU) could not repair, if it happens any malfunction, change it.
zSafety airbag assembly should be stored in the environment whose temperature is lower than 40C, relative humid-
ity is lower than 75% and is apart from electromagnetic interruption.
zForbid disassembling the airbag assembly and gas generator in it.
zForbid connect AC or DC with over 20V with ECU to avoid damage.
Supplemental restraint system
Note
Warning:
zThis product is the SRS (supplemental restraint system) equipped by JILI “YUANJIN vision” type automobile, when
the automobile frontal face is impacted heavily, this product could reduce the possible hurt for driver and passen-
ger at the front seat, but this product could not replace the safety belt. For SRS is supplemental restraint safety
system, the driver should tie safety belt. This product is single-point electronic dual-airbag system whose charac-
teristic is that all sensors and control circuits are assembled in control box and gas maker is protechny. At the
same time, this product accords with the enterprise standard “Automobile safety airbag equipment” (Q/JL001—
2001) to product.
zIn repairing process, if it does not accord with correct operation sequence to operate, SRS might happen the
accidental explosion to make heavy accident. If repair does not accord with correct procedure, even if repair does
not incur accident, SRS might disable when automobile happens accident, for example, it could not explode by
the requirement. So, when making repair (including disassembling, assembling, checking or changing any part),
it is necessary to operate by correct sequence regulated by repair manual.
zIt is necessary to confirm following works before repairing: 1. Put the ignition switch at “OFF” state. 2. Disconnect
the cathode connection of battery, and make repair after waiting for 60s. In addition, disassembled cathode
should be twisted by insulating tape to insulate. (Capacitor in ECU could keep some electric power after battery
is cut off to unfold safety airbag in some time. So, when making maintenance, if it does not wait for some time
before operating, it might incur heavy hurt accident for wrong expansion of safety airbag.)
zDo not put the parts of SRS directly under the insulation of hot air or flame.
 239 

Supplemental restraint system--Note
Special tools and measurers which any safety airbag repairing position should have:
Changeable subassembly which safety airbag repairing position should have:
a. Safety airbag assembly at the side of driver;
b. Safety airbag assembly at the side of passanger;
c. Helix cable assembly.
d. ECU assembly;
e. Steering wheel.
I. Safety airbag joint
No. ItemApplicable
(1) Terminal dual-locking organization
(2) Airbag anti-explosive organizationJoint 3, 4, 7, 8
(3) Checking organization of electric circuit connection
(4) Inadequacy connection protection organization Joint 4
(5) Joint dual-locking organization Joint 2
(6) Joint dual-locking organizationJoint 6, 7, 10
Safety airbag at the
side of passengerSafety airbag at
the side of driver
Helix
cable
Airbag controller
1. All safety airbag joints should be yellow to be easy to distinguish the joints on other automobile parts,
this could guarantee the safety performance and reliability of safety airbag joint, each kind of joint has
special function and design.
 240 
Number
a
b
c
d
eFunction
Disassemble airbag subassembly on steering wheel
Assemble and disassemble big nut on steering column
Assemble and disassemble ECU and safety airbag assembly
at the side of passenger on automobile body.
Used for electric measurement on wiring harness
Used for resistance measurement of electric ignition device
of airbag subassembly. Name and type of tool
5S hexagon wrench
Socket wrench 18S
14S socket wrench
Numeric multi-meter DT 992 type
Electric detonator tester
QJ992 type
Short
wiring
harness

Inspection
I. The inspection for airbag module at the side of
driver could be divided into three situations:
Automobile is not impacted, automobile is impacted but
airbag does not explode, and automobile is impacted and
airbag explodes.
1. Automobile is not impacted:
a. Make malfunction diagnostic inspection,
b. Check the safety airbag assembled on steering wheel
with your eyes,
including following items mainly:
Check whether the airbag has any cut, small crack or the surface and concave slot of airbag has
obvious changed color.
2. Automobile is impacted but airbag does not explode:
a. Make malfunction diagnostic inspection,
b. Check the disassembled safety airbag with your eyes, including following items mainly:
Check whether the airbag has any cut, small crack or the surface and concave slot of airbag has
obvious changed color.
Check whether wiring harness has any cut, crack or joint has any flaw,
Check whether steering wheel has distorted,
Check whether the plug and wiring harness of helix cable has been damaged, the loudspeaker wiring
harness plug and wiring harness has been damaged or distorted,
Check whether contacting board of steering wheel loudspeaker button has been distorted (if it has
been distorted, it is necessary to change with new safety airbag module, forbid repairing it),
Interruption situation could happen between safety airbag module and steering wheel lower defend-
ing cover, and when new airbag module is assembled on steering wheel, its surrounding clearance
must be even (Assemble and disassemble of driver airbag module should accord with correct step to
work).
3. Automobile is impacted and airbag explodes:
a. Make malfunction diagnostic inspection,
b. Check the disassembled safety airbag with your eyes, including following items mainly:
Check whether the plug and wiring harness of helix cable has been damaged, the loudspeaker wiring
harness plug and wiring harness has been damaged or distorted,
Check whether wiring harness has any cut, crack or joint has any flaw,
Check whether steering wheel has distorted,
Interruption situation could happen between safety airbag
module and steering wheel lower defending cover, and
when new airbag module is assembled on steering wheel,
its surrounding clearance must be even (Assemble and
disassemble of driver airbag module should accord with
correct step to work)
II. The inspection for airbag module at the side of
passenger could be divided into three situations:
Automobile is not impacted, automobile is impacted but
airbag does not explode, and automobile is impacted and
airbag explodes.
Supplemental restraint system--Inspection
Safety airbag module at
the side of passengerChange the
wiring harness
of airbag
 249 

Diagnosis of impacted automobile
No matter whether the safety airbag has been unfolded, the inspection and maintenance for impacted auto-
mobile should be made by following sequence.
1. Check the ECU diagnostic signal.
(1) Connect the diagnostic joint of diagnostic tool,
(2) Use diagnostic tool to read the diagnostic result.
2. Repair sequence
Note: For the impact, when power supply of battery is lack, diagnostic tool could not communicate
with ECU, at this time, it is necessary to check and maintain the wiring harness of panel or use
exterior power supply.
(1) When safety airbag has been unfolded,
Following parts should be changed with new ones
a. Safety airbag assembly at the side of passenger
b. ECU
c. Safety airbag assembly at the side of driver
d. Pre-tension safety belt at the side of driver and passenger
Check the following parts, if they are abnormal, change them with new ones
a. Helix cable
b. Steering wheel, steering column, combination switch
Assembling state for steering wheel of safety airbag assembly at the side of driver
a. Check whether there is any abnormal noise in steering wheel, its action is flexible and clearance is
normal.
b. Check whether the joint of wiring harness is damaged or terminal is distorted.
Supplemental restraint system--Remove malfunction
 260 

Supplemental restraint system--Disassemble and assemble
(4) Disassemble the joint of loudspeaker and airbag wiring
harness.
(5) Take down safety airbag module at the side of driver.
Note:Disassembled safety airbag assembly at the side
of driver should make its bottom surface face
the upwards, and it should be stored in clean
and dry environment.
5. Check the safety airbag assembly at the side of
driver.
6. Disassemble steering wheel:
Disassemble assembling screws to take down steering wheel
from the middle position.
Note:For the mesh of spline and column is too tight, steer-
ing wheel is hard to disconnect from the column, at
this time, pay attention to do not disassemble the
steering wheel compulsively, it is necessary to
screw the screws on column, then lift the steering
wheel up (for steering wheel connects with helix
cable at its bottom, if disassembling steering wheel
compulsively, helix cable will be damaged).
7. Disassemble the lower cover of combination switch
Disassemble three screws and lower cover of combination
switch.
8. Disassemble helix cable:
(1) Slide the upper cover of combination switch.
(2) Disassemble airbag joint from helix cable.
(3) Disassemble three fixed claws and helix cable.
Note:disassembled helix cable should be stored in
clean and dry environment.
9. Check the helix cable:
(1) When assembling new helix cable, check whether the yel-
low fixed clamp on helix cable is good, if yellow clamp drops,
please adjust by the requirement on hint card of helix cable,
insure helix cable could turn left and right for 2.5 circles on
its existing fixed position.
(2) If finding following situations, it is necessary to change the
helix cable with new one.
a. There are some scratches or cracks on joint.
b. There are cracks, concaves or flaws on wiring harness
of helix cable.
10. Remove malfunction (referring to chapter 3).
11. Make the wheels face the front.
Note: it is necessary to make the front wheels face the
front, or the wires in helix cable might break in steer-
ing process.
12. Assemble helix cable:
(1) Inspection before assembling (referring to item 9).
(2) Set the steering light switch at middle position.
The pin of steering light switch may be broken, so it must
be confirmed whether the pin is at central position.
 262 
Fixed claw

Audio system--Outdoor antenna
Outdoor antenna
Change
1. Disassemble battery negative wire
2. Put the front tyre forward
3. Disassemble safety airbag assembly at the side of the driver
4. Disassemble steering wheel
5. Disassemble integration instrument cap
6. Disassemble integration instrument
7. Disassemble panel NO.3 air outlet
8. Disassemble panel NO.1 air outlet
9. Disassemble panel center air outlet trim board
10. Disassemble glove box
11. Disassemble right front pillar trim board
12. Disassemble left front pillar trim board.
13. Disassemble the joint of the safety airbag at the side of the passenger
14. Disassemble panel
15. Disassemble right front door trim board.
16. Disassemble right side trim board.
17. Disassemble antenna assembly [67000136]
(a) Take removable antenna pillar plug apart from radio.
18. Assemble antenna assembly [67000136]
19. Assemble panel
20. Assemble helix cable.
21. Assemble steering wheel
22. Inspect steering wheel whether it dead against the center.
23. Inspect horn button.
24 Assemble horn button
25. Inspect SRS warning light
 312 

Panel/combination instrument-- panel
CodeShape
CodeShape
CodeShape
<>
=4.8
=13
2204813<>
=4.8
=19
2754819<>
=6
=20
1740620
<>
=4.8
=9.5
2754895<>
=6
=16
1400616<>
=6
=20
1400620
Panel
Preparation
1. Automobile prepares to equip with SRS airbag and safety belt pre-tension crimper.
Parking disassembling and assembling works in this chapter might influence SRS airbag. Before imple-
menting these works, it is necessary to read the notes in SRS chapter.
Change
1. Schedule for bolt, screw and screw cap
Note: when using screw driver to unclench fixing clasp or fixing clamp, it is necessary to wrap
the needled top of wrench with adhesive tape.
Hint: when disassembling or assembling panel, if necessary, use the figure and code in following
table to choose bolt, screw and screw cap.
2. Preparation
3. Disassemble leading wire of battery cathode
4. Turn front wheel to face the front
 340 
mm