wheel bolt torque GEELY FC 2008 Owner's Manual

Brake--Front brake assembly23.Assemble dustproof cover of branch pump..(a) After spreading lithium soap base glycol lubricating grease
on new dustproof cover of branch pump, assembling it in
brake branch pump.
Hint: dustproof cover should be assembled in branch
pump firmly.
(b) Use wrench to assemble fixing loop.
Note: do not damage dustproof cover.24. Assemble brake branch pump bracket.Use two bolts to assemble brake branch pump bracket.
Torque: 106
± ±± ±
± 10 N
⋅ ⋅⋅ ⋅
⋅m25. Assemble dustproof cover of brake branch pump
bracket.(a) Spread lithium soap base glycol lubricating grease on new
dustproof cover.
(b) Assemble two dustproof covers in front brake branch pump
bracket.26. Assemble sliding pin of front brake branch pump.(a) Spread lithium soap base glycol lubricating grease on the
surface of sliding part and sliding pin.
(b) Assemble two sliding pins in front brake branch pump
bracket.27. Assemble support sheet of brake block.143 28. Assemble brake block.Note: when changing brake block, muffle gasket should be changed with brake block at the same
time.
(a) Spread brake lubricating grease on both sides of every muffle gasket.
(b) Assemble muffle gasket on every brake block.
(c) When assembling inner brake block, abrasion indicator should face the upside.
Note: do not attach oil dirt or lubricating grease on the surface of brake block and brake disk.29. Assemble brake branch pump assembly.(a) Use two bolts to assemble brake branch pump.
Torque: 34
± ±± ±
± 3N
⋅ ⋅⋅ ⋅
⋅m
(b) Use joint bolt to assemble new gasket and brake hose.
Torque: 30
± ±± ±
± 3N
⋅ ⋅⋅ ⋅
⋅m
Hint: Gasket has two types: two sheets type and one type.
Bracket soft pipe should be assembled in localizing hole of branch pump firmly.30. Add brake liquid in storage tank.
31. Discharge the air in brake main pump.
32. Discharge the air in brake pipeline.
33. Check the liquid level of storage tank.
34. Check whether the brake liquid leaks.
35. Assemble front wheels.Torque: 103
± ±± ±
± 10 N
⋅ ⋅⋅ ⋅
⋅m

Brake--Hydraulic pressure control unit3. Disassemble gasket of right wheel wing.
4. Disassemble hydraulic control unit and bracket.(a) Disassemble the joint and bolt.
(b) Turn the locking bolt of joint of hydraulic control unit, and
disassemble the joint.
(c) Use special tool to disassemble the brake oil pipe on hy-
draulic control unit.
(d) Use label to mark the name of every oil pipe, and tie it on
oil pipe.
(e) Disassemble screw caps, two bolts and hydraulic control
unit and bracket.5. Disassemble hydraulic control unit assembly.Disassemble three bolts and hydraulic control unit from the bracket.6. Assemble hydraulic control unit assembly.Assemble three bolts and hydraulic control unit on the bracket with three bolts.
Torque: 4.7 N
⋅ ⋅⋅ ⋅
⋅m149Connect the front
of main cylinder
Connect the back
of main cylinder
Connect 2#
brake pipe
Connect the front left
Connect 2#
brake pipeConnect the front right

Brake--Hydraulic pressure control unit7. Assemble hydraulic control unit and bracket.(a) Assemble hydraulic control unit and bracket with screw cap
and two bolts.
Torque: 19 N
⋅ ⋅⋅ ⋅
⋅m
(b) Liking that shown in figure, use special tool to assemble
brake oil pipe on correct position of hydraulic control unit.
Torque: 15
± ±± ±
± 2 N
⋅ ⋅⋅ ⋅
⋅m
(c) Connect the joint of hydraulic control unit.
(d) Assemble bolt and connect the joint.8. Assemble gasket of right front wing.
9. Assemble right front wheel.
10. Add brake liquid in storage tank.
11. Discharge the air in main pump.
12. Discharge the air in brake pipeline.
13. Check the liquid level of brake liquid.
14. Check whether brake liquid leaks.
15. Use handle tester to check the hydraulic control
unit.150Connect the front
of main cylinder
Connect the back
of main cylinder
Connect 2#
brake pipe
Connect the front left
Connect 2#
brake pipeConnect the front right

Brake--Speed sensor of front wheelSpeed sensor of front wheelChangeHint: the process for changing right side is same as the
left side.1. Disassemble front wheels.
2. Disassemble gasket of left front wing.
3. Disassemble speed sensor of left front wheel.(a) Disassemble resinous clamp and speed sensor wiring har-
ness from fixing clamp of automobile body.
(b) Disassemble the sensor joint.
(c) Disassemble two bolts of fixing clamp of sensor wiring har-
ness from automobile body and absorber.
(d) Disassemble bolt and left front sensor.
Note: do not attach any sundries on top of sensor.4. Assemble speed sensor of left front wheel.(a) Use bolt to assemble left front sensor.
Torque: 8.0 N
⋅ ⋅⋅ ⋅
⋅m
Note: do not attach any sundries on top of sensor.
(b) Use two bolts to assemble fixing clamp of sensor wiring
harness on automobile body and absorber.
Bolt A: 9.0 N
⋅ ⋅⋅ ⋅
⋅m
Bolt B: 29 N
⋅ ⋅⋅ ⋅
⋅m
(c) Connect the joint of speed sensor.
(d) Connect resinous clamp and speed sensor wiring harness
on automobile body and fixing clamp.5. Assemble gasket of left front wheel wing.
6. Assemble front wheels.Torque: 103
± ±± ±
± 10 N
⋅ ⋅⋅ ⋅
⋅m7. Check the signal of ABS speed sensor.151

Parking rear brake pull cable assembly
Change
Hint: the changing procedure for left rear brake pull cable is same as parking right rear brake
pull cable.
1. Disassemble rear wheels.
2. Disassemble rear brake disk brake branch pump bracket assembly(LH).
3. Disassemble brake disk.
4. Disassemble support lever of parking brake shoe (LH).
5. Disassemble adjustor of parking brake shoe.
6. Disassemble parking brake inner shoe assembly (LH).
7. Disassemble parking brake exterior shoe assembly (LH).
8. Disassemble parking brake shoe lever (LH).
9. Disassemble left rear brake pull cable assembly.
Disassemble the bolt and parking left rear brake pull cable assembly from brake back board.
10. Disassemble front bottom board bracket.
11. Disassemble front part exhaust pipe.
12. Disassemble heat insulation board.
13. Disassemble parking left rear brake pull cable assembly.
Parking brake--Parking rear brake pull cable assembly
(a) Disassemble fixing clamp of rear wheel speed sensor wiring
harness.
(b) Disassemble four bolts and parking left rear brake pull cable
from automobile.
(c) Disassemble left rear brake pull cable from parking brake
balancer, then disassemble parking left rear brake pull cable.
14. Assemble parking left rear brake pull cable
assembly.
(a) Connect parking left rear brake pull cable on parking brake
pull cable balancer.
(b) Assemble parking left rear brake pull cable with four bolts.
Torque: 5.4 N
⋅ ⋅⋅ ⋅
⋅m
(c) Connect resinous clamp of speed sensor wiring harness of
 158 

Parking brake--Parking rear brake pull cable assembly
rear wheel to fixing clamp.
15. Assemble No.2 clapboard.
16. Assemble front part exhaust pipe assembly.
17. Assemble front bottom board bracket.
18. Connect parking left rear brake pull cable assembly.
Assemble parking left rear brake pull cable assembly to brake
back board with bolt.
Torque: 7.8 N
⋅ ⋅⋅ ⋅
⋅m
19. Spread high temperature lubricating grease.
20. Assemble support lever of parking brake shoe (LH).
21. Assemble parking brake exterior shoe assembly
(LH).
22. Assemble parking brake inner shoe assembly (LH).
 159 

Steering column--Steering systemSteering column--Steering system
Steering column--Steering systemSteering column--Steering systemSteering column--Steering system
Align the mark
(b) Align the mark on sliding yoke and middle shaft.
(c) Assemble B bolt and tighten A bolt.
Torque: 35 ± 3 Nxm
Hint:When changing new sliding yoke, it is neces-
sary to adjust the front wheel at the front, and
make the bolt hole surface of sliding yoke face
the back (liking that shown in figure), then as-
semble the bolt.
21. Adjust front wheel at the front.
22. Assemble helix cable assembly (equipping with
SRS) [67000121]
23. Put the helix cable assembly at central position
(equipping with SRS)
(a) Check whether the front wheel faces the front.
(b) Turn helix cable counter-clockwise with hand until it could
not turn.
(c) Then turn helix cable 2.5 clockwise and align the mark.
Hint:helix cable could turn left or right from central
position for 2.5 rounds.
24. Assemble steering wheel assembly [67010001]
(a) Align the mark on steering wheel and main shaft assembly.
(b) Assemble the fixed screw cap of steering wheel.
(c) Connect the joint.
25. Assemble safety airbag assembly at the side of driver [67010011]
Warning:
zForbid using SRS parts on other automobiles, when changing any part, it is necessary to use new
product.
zIf safety airbag assembly at the side of driver once dropped or exterior shell and joint has crack,
concave or other distortions, it is necessary to change with new product.
zWhen assembling the airbag assemble at the side of driver, it is necessary to pay attention to airbag
wiring harness could not interrupt other parts or be clamped by other parts.
(a) Connect the end.
(b) Connect the joint of airbag.
(c) After assembling the safety airbag assembly at the side
of driver, insure planetary screw of concave slot contacts
with screw shell.
(d) Use planetary screwdriver to tighten two screws.
Torque: 8.8 Nxm
26. Check the central point of steering wheel
27. Check SRS warning light (equipping with SRS)
Align the
mark
 197 
planetary
screws screw shell

Power steering--Power steering oil pump assembly
Power steering oil pump assembly
Overhaul
1. Disassemble front wheel
2. Disassemble right bottom defender board [68000004]
3. Disassemble driving belt.
4. Disassemble oil storage tank to the No. 1 oil pipe
of power steering pump
Disassemble fixed clamp, and take down the oil storage tank
to the No. 1 oil pipe of power steering pump.
5. Disassemble in-out oil pipe assembly of power
steering gear [64000131]
(a) Use special tool to disassemble in-out oil pipe assembly.
(b) Disassemble the bolts and disconnect the fixed clamp of
in-out oil pipe.
6. Disassemble rear bracket of power steering pump
Disassemble the bolt and rear bracket of power steering pump.
7. Disassemble power steering oil pump assembly
[64000132]
(a) Disconnect the joint of oil pressure switch.
(b) Disassemble two bolts, two screw caps, then take down
the power steering oil pump assembly.
8. Assembly power steering oil pump assembly
(a) Assemble power steering oil pump assembly with two
bolts and two screw caps.
Torque: 37 N
x xx x
xm
(b) Connect the joint of oil pressure switch.
Note: the joint could not contact any oil.
9. Assemble the rear bracket of power steering oil pump assembly
Assemble rear bracket of power steering oil pump assembly with bolts.
Torque: 37 N
x xx x
xm
Hint:Insure the stop lever of bracket has contacted the body of power steering pump, then
tighten the bolt.
 203 
Special tool

10. Connect the in-out oil pipe assembly of power
steering gear [64000131]
(a) Assemble fixed clamp of in-out oil pipe with bolt.
Torque: 7.8 N
xm
(b) Connect in-out oil pipe with special tool.
Torque: 41 Nz
xm
Hint:
zUse torque wrench whose lever length is 345 mm.
zSpecial tool should be parallel with torque wrench,
only this could make practical torque value.
11. Connect the N0. 1 oil pipe of oil storage tank to power steering oil pump assembly.
Connect oil pipe with fixed clamp.
12. Assemble driving belt.
13. Assemble front wheel.
Torque: 103 ± 10 Nx xx x
xm
14. Add power steering oil.
15. Exhaust the air in power steering system.
16. Check whether there is any oil leakage.
17. Assemble right bottom defender board of engine [68000004].
Power steering--Power steering oil pump assembly
Special
tool
¸Ü¸Ü
¸Ü¸Ü¸Ü¸Ë¸Ë
¸Ë¸Ë¸Ë³¤³¤
³¤³¤³¤¶È¶È
¶È¶È¶È
 204 

Power steering--Power steering gear assembly
29. Assemble steering No.2 dust-proof cover.
(a) Insure steering gear hole is not plugged by lubricating
grease.
Hint: if hole is plugged, the pressure in dust-proof
cover when steering wheel turns after combin-
ing will change.
(b) Assemble dust-proof cover, fixed clamp and new iron wire.
Note: do no t hurt or bend dust-proof cover.
(c) After coiling dust-proof cover with iron wire for two circles,
turn it for several circles to fix it.
(d) Liking that shown in figure, bend iron wire to rotating di-
rection to prevent it from hurting dust-proof cover.
Hint: assemble the other side with same method.
30. Assemble No.1 dust-proof cover of steering gear.
31. Assemble left ball head of transversal lever .
(a) Screw locking cap and transversal lever ball head in gear
terminal lever until aligning the mark.
(b) After adjusting front wiring harness, tighten the screw cap
(referring to page 80).
Torque: 74 ± 5 N
xm
Hint: assemble the other side with same method.
32. Assemble right ball head of transversal lever .
33. Assemble power steering gear assembly [64000133].
(a) Assemble power steering gear assembly on beam with
four bolts.
Torque: 58 N
xm
 209 
Align the mark