window GEELY FC 2008 Owner's Manual

Anti-stealing and door lock--Electric door lock control system
Malfunction phenomenon
“Door locker control system” does not work
(all).
Door locking/unlocking malfunction (use
handle operation and key operation)
Door locking/unlocking malfunction (use
key)
Malfunction of key keeping protection func-
tion
Only one door locker does not workPossible malfunction part
1. DOOR fuse (panel J/B)
2. Wiring harness
1. Electric window main switch (door control switch)
2. Wiring harness
1.
Door at the side of driver assembly (door control switch)
2. Wiring harness
3. Door locker connecting rod is loosen
1. Anti-versa lock supervising switch
2. Door control light switch
3. Wiring harness
1. Door locker electric motor
2. Wiring harnessReferred page
-
-
359
-
359
-
-
359
-
-
359
-
Malfunction phenomenon table
 358 

Engine cover/automobile door--Front automobile door
8. Disassemble left front glass assembly [68000146]
Hint: insert the cloth in door steel board to prevent it from
scratching the glass.
(a) Turn the door glass until the bolts happens in repairing
hole.
(b) Disassemble two bolts and door glass.
Note: do not damage the door glass.
Hint: pull the door glass upwards to disassemble it.
9. Disassemble seal tape of left front glass guide slot
[68000161]
10. Disassemble left front door glass lift assembly
[67000122]
(a) Disassemble the joint.
(b) Disassemble six bolts and glass lift.
11. Spread lubricating grease on automobile body.
12. Disassemble left front door window glass guide
slot assembly [68000148]
Disassemble the screw and door framework rear lower bracket.
13. Disassemble left front door locker organization as-
sembly [68000152]
(a) Disassemble the joint.
(b) Disassemble connecting rod from exterior handle.
(c) Disassemble the bolt and screw.
(d) Use planetary socket wrench (T30) to disassemble three
planetary screws and door locker.
(e) Disassemble two screws and left front door locker organi-
zation driver.
14. Spread lubricating grease on automobile body.
Spread MP lubricating grease on sliding and turning parts of
lift assembly.
15. Disassemble left front door exterior handle pedestal.
(a) Use planetary socket wrench to disassemble the screw
and door key tank.
(b) Disassemble exterior handle from exterior handle pedestal.
(c) Use planetary socket wrench to disassemble the screw
and left front door exterior handle pedestal.
 370  16. Assemble left front door locker organization assembly [68000152]
(a) Use two screws to assemble left front door locker organization driver.
(b) Use planetary socket wrench (T30) to assemble three planetary screws and front door locker assembly.
Torque: 5.0 N
⋅ ⋅⋅ ⋅
⋅m
(c) Assemble the bolts and screws.
(d) Connect connecting rod to exterior handle.
(e) Connect the joint.

Engine cover/automobile door--Front automobile door
17. Assemble left front door glass lift assembly [67000122]
(a) Use six bolts to assemble left front door glass lift.
Torque: 8.0 N
⋅ ⋅⋅ ⋅
⋅m
(b) Assemble electric window lift and door glass.
(c) Connect electric window switch to wiring harness and turn ignition switch to ON.
(d) Operate UP and DOWN several times by hand repeatedly.
(e) Check whether the AUTO UP→AUTO DOWN of automatic operation is normal.
Hint:
zWhen it is set up again, anti-clamping protection function does not work.
zAfter implementing AUTO UP operation to close window completely, if automobile window
could not be operated downwards, it is necessary to set up the lift again.
(f) Check the function of electric window.
 371  18. Check the function of electric window
19. Assemble repairing hole cover of left front door
Hint:
zWhen assembling repairing hole cover, pull out con-
necting rod and joint from repairing hole cover.
zAfter assembling repairing hole cover, connecting rod
and joint could not be bent or concaved.
zAfter assembling repairing hole cover, it is necessary
to confirm the affixing situation of adhesive tape.

Engine cover/automobile door--Rear automobile doorRear automobile doorOverhaulHint:zWhen assembling, please work by the sequence which is opposite with disassembling
sequence; if necessary, it will have assembling instruction..zOverhaul procedure for right side is same as the left side.1. Disassemble left rear door control panel assembly [68000176]Use screw driver to disassemble left rear door control panel assembly.Fixing
clasp
Fixing
clasp 373  2. Disassemble left rear door inner trim board assem-
bly [68010057](a) Disassemble three screws.
(b) Disconnect the fixing clamp, then pull inner trim board up-
wards to disassemble it.3. Disassemble left door inner handle assembly
[68010051]Disassemble inner handle and two pull cables from inner handle.4. Disassemble left rear door repairing hole cover.Disassemble repairing hole cover.5. Disassemble exterior seal tape of left rear door glass
[68000196]
6. Disassemble seal tape of left rear glass guide slot
[68000199](a) Disassemble seal tape of left rear glass guide slot.7. Disassemble left rear door window glass guide slot
assembly [68000187]Disassemble two bolts and comparting pillar of rear window.8. Disassemble left rear door triangle glass [68000181](a) Disassemble left rear door triangle glass.
Note: do not damage the glass.
(b) Disassemble corner window waterproof rubber from the glass.9. Disassemble left rear glass assembly [68000179]Hint: insert the cloth in the door steel board to prevent the glass from scratching.
(a) Drop the door glass.
(b) Incline door glass and disassemble the roller pole of lift from glass leading slot to disassemble door
glass.10. Disassemble left rear door lift assembly [67000124](a) Disassemble the joint.
(b) Disassemble four bolts and window lift.

Exterior/inner trim board--Inner trim board of top29. Disassemble the pothook of sun shade [68010086]Turn the pothook of sun shade to left for 90°, then disassemble
it.30. Disassemble fixing pedestal of rear window sun
blind.Use screw driver to turn the fixing pedestal of sun blind for 90°,
then disassemble it.31. Disassemble trim tape of top sunroof [67010010]
32. Disassemble inner trim board of top [68010035](a) Use screw driver to disassemble inner trim board of top.
Hint: before using screw driver, its needled top should
be twisted by adhesive tape.
(b) Disassemble three fixing clamps and inner trim board of
top.
(c) Take out inner trim board of top from rear door.33. Assemble inner trim board of top [68010035](a) Liking that shown in figure, align the mark, then fix the wir-
ing harness of top with adhesive tape.
(b) Use three fixing clamps to assemble inner trim board of top.34. Assemble the pothook of sun shade [68010086]Turn the pothook of sun shade to make fixing claw proturde,
then assemble sun shade.35. Assemble rear row chair left backrest assembly
[68010078]
36. Assemble rear row chair right backrest assembly
[68010079]
37. Assemble rear row chair backrest assembly
[68010076]Fixing
clamp
Adhesive
tape393