tire size GEELY FC 2008 Workshop Manual

Front suspension - Front wheel alignmentFrontRearIf toe-in is not within specification, please adjust left and
right levers of steering gear.4. Adjustment of toe-in(a) Remove dust cover fixing clip.FrontRearToe-in(Total)Front wheel alignmentAdjustment1. Inspection(a) Check tire is worn and inflation pressure is proper.
Tire inflation pressure under normal temperature:Tire size Front and rear kPa*1 It is used under the condition of speed below 160 km/h.
*2 It is used under the condition of speed above 160 km/h.
(b) Check tire run-out with dial indicator.
Tire run-out: 3.0mm.2. Measurement of vehicle heightVehicle height:
(General road)
(Coarse road)
Measuring point:
A. Height for ground and front wheel center
B. Height for ground and bolt center in front of lower
control arm
C. Height for ground and fixed bolt center of rear axle beam
D. Height for ground and rear wheel center
Note: adjust vehicle height to standard value before checking front wheel alignment.
If vehicle height does not conform to regulations, please shake upward and downward or lift vehicle
body to adjust vehicle height.3. Inspection of toe-inToe-in:Front87

Tire and wheel- wheel and tire systemTire and wheelWheel and tire systemInspection1. Check tire.(a) Check tire is worn and inflation pressure is proper.
Cold tire inflation pressure:
*1 It is used under the condition of speed below 160 km/h.
(b) Check tire run-out with dial indicator.
Tire run-out: 2. Adjust tire position.
Hint:see adjusting position of tire shown in the dia-
gram whether there is spare tire or not.3. Check wheel balance.(a) Check and adjust with off-the-car balancing machine.
(b) Check and adjust with in-the-car balancing machine if
necessary.
Unbalanced mass after adjusting: 4. Check axial clearance of front wheel bearing
(see Page 123).
5. Check end surface run-out of front wheel shaft hub
(see Page 123).
6. Check axial clearance of rear wheel bearing
(see Page 129).
7. Check end surface run-out of rear wheel shaft hub
(see Page 129).
8. Check front suspension is loose.
9. Check steering linkage is loose.
10. Check ball joint is loose.Tire size Front and rear kPaFront109

(3) Fix the module on wheel.
a. Assemble three bolts with gasket on two assembling
holes of left, middle and right support pin of safety airbag
module at the side of passenger.
Size of bolt: L 35.0 mm
M 8.0 mm
Note: screw the bolts with hand, but they could not
be screwed too tightly, 2/3 L of bolts should
expose.
2. Explosion of safety airbag assembly at the side of passenger.
(1) Prepare a battery as detonating power (12±1)V.
(2) Disassemble safety airbag assembly at the side of passenger, and connect the airbag short wiring
harness on gas generator.
Warning: when storing safety airbag module at the side of driver, it is necessary to keep upper
surface face upwards.
Supplemental restraint system--Scrap treatment for safety airbag
Old tire
without hud
Wiring harness
for explosion
Wiring harness
for explosion
Left and
right small
bracket
 267 
(5) Fix three scraped old tyres without wheel hub on the fixed
tyre of safety airbag assembly at the side of driver. The
terminal end of unfolding wiring harness is 10m apart from
wheel of fixed airbag at least.
Width: 185mm
Inner diameter: 360mm
(6) Cut off the joint of wiring harness used for unfolding of safety
airbag assembly at the side of driver at the place apart from
the automobile, then connect it with two ends of battery.
(7) Treatment for explosive module.
Disassemble the safety airbag module at the side of driver
from wheel, and put it in ethane plastic bag, then bind the
bag for treatment with other parts.