battery GEELY FC 2008 Repair Manual

Audio system--Outdoor antenna
Outdoor antenna
Change
1. Disassemble battery negative wire
2. Put the front tyre forward
3. Disassemble safety airbag assembly at the side of the driver
4. Disassemble steering wheel
5. Disassemble integration instrument cap
6. Disassemble integration instrument
7. Disassemble panel NO.3 air outlet
8. Disassemble panel NO.1 air outlet
9. Disassemble panel center air outlet trim board
10. Disassemble glove box
11. Disassemble right front pillar trim board
12. Disassemble left front pillar trim board.
13. Disassemble the joint of the safety airbag at the side of the passenger
14. Disassemble panel
15. Disassemble right front door trim board.
16. Disassemble right side trim board.
17. Disassemble antenna assembly [67000136]
(a) Take removable antenna pillar plug apart from radio.
18. Assemble antenna assembly [67000136]
19. Assemble panel
20. Assemble helix cable.
21. Assemble steering wheel
22. Inspect steering wheel whether it dead against the center.
23. Inspect horn button.
24 Assemble horn button
25. Inspect SRS warning light
 312 

Horn--system
Horn system
Horn system
Position
Inspect
1. Inspect the relay
(a) Inspect Whether horn relay (mark: HORN)is conduct
If the conduction situation does not accord with regulations, re-
place the relay.
Horn (alt)
Horn (undertone)
 316 
Condition regular situations
Normal 1-2conduction
Supply battery voltage 3-5conduction
to Terminal 1 and 2avometer connection terminal

Windshield/bodywork glass/wing mirror--Electric window control system
Switch position avometer terminalssituations
UP 4-5, 2-3conduction
OFF 4-5, 1-3conduction
DOWN 2-5, 1-3conduction
Battery terminals working direction
Battery anode lead-terminal 5 main driving axis working
Battery cathode lead-terminal 4 as clockwise
Battery anode lead-terminal 4 main driving axis working
Battery cathode lead-terminal 5 as anticlockwise
2. Inspect electric window switch assembly
Active switch, inspect the conduction among the joint terminals.
If the conduction does not limit to regulations, replace electric
window main switch.
3. Inspect left rear electric window motor assembly.
(a) Inspect the function of left rear electric window assembly.
(1) Inspect whether the motor works calmly.
4. Inspect electric window shift relay [67000061]
Check the conduction of relay (mark: P/W)
If the conduction does not limit to regulations, replace relay.
 320 
Conditionsavometerregular situations
Always 1-2conduction
Supply battery voltage
To that between terminal 13-5 conduction
and terminal 2

Windshield/bodywork glass/wing mirror--Fogbroom system
Inspect
1. Inspect the relay
Inspect the conduction of rear window demist(defrost) relay
(mark: DEF)
If the conduction does not accord with the regulations, replace
relay.
 328 
Conditionsavometer terminals regular situations
Always 1-2conduction
Supply battery voltage
between terminal1 and 3-5 conduction
Terminal2

Windshield/bodywork glass/wing mirror--Electric rearview mirror control system
INSPECT
1. Inspect rear view mirrors switch
Inspect conduction of rearview mirror.
(1) Adjust left or right for side of the switch.
Inspect conduction of rearview mirror on left side
Replace the switch if it does not accord with the regulations.
(2) Adjust right side of left and right switch.
Inspect conduction of rearview mirror on right side
Replace the switch if it does not accord with the regulations.
(3) Inspect conduction of retracting switch
Switch positionsAvometer terminalsRegular situations
ON - Not conduction
Up 3-8, 6-7Conduction
Down3-7, 6-8Conduction
Left 2-8, 6-7Conduction
Right2-7, 6-8Conduction
Switch positionsAvometer terminalsRegular situations
Position of driving 8-9, 7-10Conduction
Position of retracting 8-10, 7-9Conduction
Replace the switch if it does not accord with the regulations,
2. Inspect rear rear view mirror
(a) Inspect motor function of rearview mirror
(b) Inspect function of electric retracted motor
Battery terminals Positions of rearview mirror
Positive wire (+) -A
Turn left
Negative wire (-) -B
Positive wire (+) -B
Turn right
Negative wire (-) -A
Positive wire (+) -C
Turn up
Negative wire (-) -B
Positive wire (+) -B
Turn down
Negative wire (-) -C
Left and right
adjusting switchFolding switch
(optional)
Rearview
mirror
switch
 332 
Switch positionsAvometer terminalsRegular situations
ON - Not conduction
Up 5-8, 6-7Conduction
Down5-7, 6-8Conduction
Left 4-8, 6-7Conduction
Right4-7, 6-8Conduction

Windshield/bodywork glass/wing mirror--Electric rearview mirror control system
Replace the rearview mirror if actuation does not accord with regulations. Notes:
zWhen repeat the same inspection, cut off the voltage of battery, then inspect again with
same steps.
zWhen supply battery voltage, the rearview mirror will not retract even if trying to move the
crust of rearview mirror.
Outer rearview mirror assembly L
Outer rearview mirror assembly R
L terminal
connecting wireL terminal
connecting
wire
assembly L assembly R
 333 
Positions of rearview mirror
A (position of driving)
B (between position of driving
and retracting)
C (position of retract)Connection style
Connect wire G to positive
Connect wire D to negative
Connect wire D to positive, connect wire G to negative
Connect wire G to positive, connect wire D to negative
Connect wire D to positive
Connect wire G to negativeActuated style
Not actuated
A-B-C
C-B-A
Not actuated
Positions of rearview mirror
A (position of driving)
B (between position of driving
and retracting)
C (position of retract)Connection style
Connect wire D to positive
Connect wire G to negative
Connect wire G to positive, connect wire D to negative
Connect wire D to positive, connect wire G to negative
Connect wire G to positive
Connect wire D to negativeActuated style
Not actuated
A-B-C
C-B-A
Not actuated

Panel/combination instrument--combination instrument
(b) Inspect light warning buzzer function
(1) Disassemble combination instrument.
(2) Connect battery positive wire to terminal A5 and nega-
tive to terminal A1 and A2.
(3) Connect battery positive wire to terminal A18 and nega-
tive to terminalA17,inspect buzzer.
Audio buzzer: long buzzes
(4) When buzzer works, connect battery positive wire to ter-
minal A4,inspect whether buzzer stop working.
11. Inspect key buzzer
(a) Inspect when key buzzer and light warning buzzer works
together, only key buzzer works.
(1) Insert the key, when driver seat door opens, turn ignition
switch to OFF (LOCK or ACC). inspect key buzzer works
1HZ discontinuously.
(b) inspect key buzzer function
(1) Disassemble combination instrument.
(2) Connect battery positive wire to terminal A5 and nega-
tive to terminal A1 and A2.
(3) Connect battery negative wire to terminal A17 and B8,
inspect buzzer which should work discontinuously.
(4) When buzzer works, connect battery positive wire to ter-
minal A4,inspect whether buzzer stop working.
12. Inspect brake system indictor
(a) Inspect parking brake system indictor
Key warning
switch
Key switch
1G gear
Pull out the key
Open driver door
Buzzer
B8
B1
A1A20
(1) Disassemble the joint of parking brake switch, and earth terminals of wiring harness side joints.
(2) Turn ignition switch to ON, inspect brake system indictor light lights.
(b) Inspect brake oil level indicator light
(1) Disassemble the joint of brake oil level indicator light, connect terminal of wiring harness side
joints.
(2) Turn ignition switch to ON, inspect brake system indicator light lights.
 338 

Panel/combination instrument-- panel
CodeShape
CodeShape
CodeShape
<>
=4.8
=13
2204813<>
=4.8
=19
2754819<>
=6
=20
1740620
<>
=4.8
=9.5
2754895<>
=6
=16
1400616<>
=6
=20
1400620
Panel
Preparation
1. Automobile prepares to equip with SRS airbag and safety belt pre-tension crimper.
Parking disassembling and assembling works in this chapter might influence SRS airbag. Before imple-
menting these works, it is necessary to read the notes in SRS chapter.
Change
1. Schedule for bolt, screw and screw cap
Note: when using screw driver to unclench fixing clasp or fixing clamp, it is necessary to wrap
the needled top of wrench with adhesive tape.
Hint: when disassembling or assembling panel, if necessary, use the figure and code in following
table to choose bolt, screw and screw cap.
2. Preparation
3. Disassemble leading wire of battery cathode
4. Turn front wheel to face the front
 340 
mm

Anti-stealing and door lock--Electric door lock control system
Inspection
1. Check driver sear door locker assembly.
(a) Liking that shown in figure, check the conduction of every
terminal of door key switch.
If the conduction does not accord with the regulation, change
the switch.
(b) Liking that shown in figure, supply battery voltage to terminal,
and check the function of door locker.
If the function does not accord with the regulation, change
the door locker assembly.
Open Close
Open Close
 359 
Position of switch Terminal connected by avometerRegulated situation
LOCK 2-4Conduction
OFF - Not conduction
UNLOCK 1-2-3 Conduction
Condition Function
Supply battery anode to No. 6 terminal, cathode to No.5 terminalOpen
Supply battery anode to No. 5 terminal, cathode to No.6 terminalClose

Anti-stealing and door lock--Electric door lock control system
2. Check front passenger seat door locker assembly
Liking that shown in figure, supply battery voltage to terminal,
and check the function of door locker.
If the function does not accord with the regulation, change the
door locker assembly.
3. Check the left rear and right rear door locker assembly.
Liking that shown in figure, supply battery voltage to terminal,
and check the function of door locker.
If the function does not accord with the regulation, change the
door locker assembly.
OpenClose
Open
Close
 360 
Condition Function
Supply battery anode to No. 6 terminal, cathode to No.5 terminalOpen
Supply battery anode to No. 5 terminal, cathode to No.6 terminalClose
Condition Function
Supply battery anode to No. 6 terminal, cathode to No.5 terminalOpen
Supply battery anode to No. 5 terminal, cathode to No.6 terminalClose