auxiliary battery GEELY FC 2008 Workshop Manual
[x] Cancel search | Manufacturer: GEELY, Model Year: 2008, Model line: FC, Model: GEELY FC 2008Pages: 419, PDF Size: 13.87 MB
Page 37 of 419
![GEELY FC 2008 Workshop Manual Engine mechanismEngine assemblyInspection1. Check coolant.
2. Check engine oil.
3. Check battery.
4. Check air filter assembly.
5. Check spark plug [4G18-3705113].
6. Check drive belt [4G18-1307107].H GEELY FC 2008 Workshop Manual Engine mechanismEngine assemblyInspection1. Check coolant.
2. Check engine oil.
3. Check battery.
4. Check air filter assembly.
5. Check spark plug [4G18-3705113].
6. Check drive belt [4G18-1307107].H](/img/58/57161/w960_57161-36.png)
Engine mechanismEngine assemblyInspection1. Check coolant.
2. Check engine oil.
3. Check battery.
4. Check air filter assembly.
5. Check spark plug [4G18-3705113].
6. Check drive belt [4G18-1307107].Hint: do not check belt tension, because automatic tensioner is applied.7. Check ignition timing.(a) Warm up engine.
(b) Connect timing lamp to engine.
(c) Check ignition timing at idle speed.
Ignition timing: before top dead center Note: when checking ignition timing, place
transmission at neutral position.
Hint: After run the engine for 5 seconds with rotating
speed of 1000-1300rpm, check the engine could
recover to idle running.8. Check engine idle speed.(a) Warm up engine and run it at idle speed.
(b) Read engine rotating number in data flow with diagnostic instrument.
(c) Check idle speed.
Idle speed: about 750-850rpm
Notes:When checking idle speed, place cooling fan at OFF position.Turn off all auxiliary devices and air conditioner.Engine mechanism - Engine assemblyK-line 26
Page 272 of 419

Supplemental restraint system--Disassemble and assemble
Disassemble and assemble
Electronic control unit of safety airbag (ECU)
1. Note (referring to chapter 1)
2. Disassembling sequence:
(1) Disassemble the cover board at the side of central channel (or disassemble auxiliary panel).
(2) Disassemble the connector connecting with safety airbag ECU.
(3) Disassemble the ECU.
3. Assembling sequence
(1) Check the ECU assembly, and make arrow direction on hint card point to running direction of automobile.
(2) Assemble the connector connecting with safety airbag ECU, the connector should be locked firmly (if
you hear a light sound “KA” when press the connector, this shows it has been locked).
a. Fix the special bolt used by controller assembly on assembling position of central channel, and
confirm it has been assembled firmly.
b. Assemble the cover board at the side of central channel (or assemble auxiliary panel).
c. Connect the cathode of battery.
4. Main notes of assembling operation:
(1) When assembling ECU assembly, pay attention to that ECU assembly could not be impacted.
(2) Inspection after the assembling
a. Set the ignition switch at ON position.
b. Indicating light illuminates at 7 second, and continues to extinguish.
c. If it does not extinguish, it is necessary to check and remove malfunction.
Note: if ECU could not be assembled correctly, safety airbag will not work normally.
5. Inspection: referring to chapter 2.
6. Removing malfunction: referring to chapter 3.
3. Place the steering wheel and front wheels correctly
and make them face the front, and take out ignition
switch key, then do not operate it in 60 seconds af-
ter disassembling the cathode of battery.
4. Disassemble safety airbag assembly at the side of
driver:
(1) Guarantee the wheels face the front.
(2) Use 5s hexagon socket-head wrench to loosen the two plan-
etary bolts.
(3) Pull out the safety airbag assembly at the side of driver
from upside of steering wheel.
Safety airbag assembly at the side of driver
1. Note (referring to chapter 1).
2. Use the flash or malfunction diagnostic tool to test malfunction (referring to chapter 1
and 3).
261