fog light bulb GEELY FC 2008 Workshop Manual

Light--Light SystemThe phenomena table1. front combination lights and tail lightPhenomena
Only one front combination light
lights
Low beam headlights do not light
(all)
distance lights do not light (all)
Distance light do not light (one
side)
Flare does not light
Front combination lights are too
dark
Only one rear combination light
lights
Rear combination lights do not light
(front combination lights are normal)
Rear combination lights do not light
(front combination lights are abnormal)Reference pages
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-LightLight SystemNotes1. Notes for changing the front combination bulb(a) When the surface of halogen bulbs (the bulb of front assembled headlamp and front fog light) touches
oil, their working life will be shorten. When it lights, it becomes hot.
(b) Because of pressured gas in halogen bulbs (the bulb of front assembled headlamp and front fog
light), the bulb may explode and pieces of broken glass disperse around. So deal with it carefully.
(c) If the time after disassembling the bulb from lamp carrier is too long, the mirror may be polluted by
dirties or hydrosphere. You should prepare a new bulb,then replace it.
(d) Replace it with the lamp of same wattage.
(e) Assemble the changing bulb on the lamp carrier firmly, or it may bring mirror mirage or water intrusion.
(f) Do not touch the black of the top of glass, or it may shorten its working life.Possible part
1.bulb
2.fuse
3.wiring harness
1.fuse
2.relay
3.left combination switch
4.wiring harness
1.fuse
2.relay
3.left combination switch
4.wiring harness
1.bulb
2.wiring harness
1.left combination switch
2.flare
3.wiring harness
1.bulb
2.wiring harness
1.bulb
2.wiring harness
1.bulb
2.wiring harness
3.left combination switch
4.wiring harness
1.fuse
2.relay 279 

Light--Light System 280  2. Fog light System
3. Turning and emergency warning light systemEmergency warning light and turn
light does not light
Emergency warning light does
not light (turning light is normal)
Turn light does not light
(Emergency warning light is normalSide turning light does not light
(warning light is normal)
One side of turning light does not
light
One side of turning light does not
light
Only one bulb does not light1. (meter) fuse
2. (turn) fuse
3. ignition switch
4. flasher assembly
5. wiring harness
1. Emergency warning light switch
2. wiring harness
1. turn light switch
2. wiring harness
1. turn light switch
2. wiring harness
3. bulb
1. turn light switch
2. wiring harness
3. bulb
1. turn light switch
2. wiring harness
1. bulb
2. wiring harnessThe light control switch switches on,
the front fog lights do not light (front
combination lights are normal)Lamp switch turn to “HEAD”. front fog
lights do not light (front combination light
do not light)Only one front fog light do not light
Rear fog lights do not light (front
combination lights are normal)
(front fog lights are normal)
Rear fog lights do not light (front fog
lights do not light)1.(front fog light)fuse
2.fog light relay
3.fog light switch
4.wiring harness
1.other parts
2.wiring harness
1.bulb
2.wiring harness
1.fuse
2.rear fog light switch
3.wiring harness
4.bulb
1.other parts
2.wiring harness
3.bulb
4.front fog light switch
5.rear fog light switchphenomena
Possible part
Reference pagesphenomena
Possible partsReference pages

Light--Light System
(a) Inspect the conduction of B pillar control switch assembly
(1) Inspect the conduction between terminal 1 and bodywork earth, when switch works.
Standard:
ON (when press the switch): conduction
OFF (when un-press the switch): not conduction
7. Inspect the C door pillar control switch assembly [67000076]
(a) Inspect the conduction of C pillar control switch assembly
(1) Inspect the conduction between terminal 1 and bodywork earth,when switch works.
Standard:
ON (when press the switch): conduction
OFF (when un-press the switch): not conduction
8. Trunk light switch assemble [67000073]
(a) Inspect the conduction of Trunk light switch
Standard:
ON (when press the switch): conduction
OFF (when un-press the switch): not conduction
9. Front fog light relay [67000071]
(a) Inspect the conduction of front fog light relay
(1) Inspect the conduction among terminals
Standards:
Avometer terminalsregular situations
1-2 conduction
3-5 not conduction
10. Inspect rear fog light switch of instrument block
left switch units [67010003].
(a) Inspect battery’s positive wire connects to terminal 1,nega-
tive connects to terminals 7.
(b) Connect a 3.4W test bulb from battery’s positive wire to
terminal 3.
(c) Inspect lighting switch, indicator light of assembled instru-
ments and test bulb should light. If it does not accord with
regularizations, replace the switch.
11. Inspect door light assembly [67000107]
Inspect the conduction among terminals.
If the conduction does not accord with regularizations, replace
the switch.(2) Supply battery voltage(10-14V) to terminal1 and terminal2, then inspect the conduction between
terminal 3 and terminal 5.
Standard: conduction
1
 285 

Light--Front fog light joint
Front combination light (LH)
Subassembly
Left front combination
light units
Front combination
light bulb
Front combination
light bulb
Front combination light
bulb joint Ultrasonic sensor joint Radiator cover
assembly
Front fog light
joint
Light
seat cap
Bulb joint
Bulb
Bulb
Front fog light joint
Front bumper
 286 

Light--Front fog light joint
Change
Notes:
zAssemble according to the opposite of disassemble. Instructions comes when necessary.
zThe replace procedure are the same on the left and right side.
zReferring to the drawing of front combination light on page 286.
1. Disassemble Radiator cover assembly (reference to page 380)
2. Disassemble left front tyre lining (reference to page 380)
3. Disassemble right front tyre lining (reference to page 380)
4. Disassemble front bumper (reference to page 380)
5. Disassemble left front combination light assembly [67000102]
(a) Disassemble three bolts
(b) Disassemble four joints
(c) Pull combination light ahead
(d) Disassemble two light seat cap and four bulbs.
Adjustments
1. Adjust front combination light focus only
(a) Parking car should accord to the following situations:
zFront combination light around does not be distorted or damaged.
zPark the car on flat road.
zTyre pressure limits to the regular number value
zThe driver is on driving seat and the car is ready to go(gasoline tank in full)
zThe car weaves fore-and-aft for many times.
(b) Inspect front combination light focus
(1) Prepare for thicker white paper
(2) Arise the paper plumb at the distance of 300cm from headlight.
(3) Make sure centerline of the car makes 90 degree angle with paper’s surface as following drawing.
(4) Draw a level line (H line) on the paper which headlight can irradiate.
(5) Draw a plumb line (V line) on the paper to across centerline of the car.
(6) Draw two level lines (V RH and V LH) in the area where two side lights can irradiate.
(7) Draw a level line(connect the middle signal of two low beam headlight) to the area where headlight
can irradiates.
Clues on: H RH and H LH lines are 0.57 lower than level line(H line)of light.
(8) Start the engine.
(9) Turn the front assembled switch to ON.
Pin
 287 

Light--Front fog light joint
Front fog light
Components
 289 
Front fog light joint
Left front fog light unit
Bulb

Light--Front fog light joint
Change
Notes:
zAssemble according to the opposite of disassemble.
Instructions comes when necessary.
zThe replace procedure are the same, left and right side.
zReferring to the drawing of front combination light on
page 286
1. Replace front fog light bulb
(a) Disassemble front fog light seal cap
(b) Press front fog light bulb spring
(c) Disassemble the bulb
Adjustments
1. Adjust front fog light optic axis
(a) Tyre pressure limits to regular number values.
(b) Start the engine.
(c) Adjust fog light optic axis by turning the optic axis adjust-
able button on the vertical direction.
 290 

Light--Rear fog light
Rear fog light
Components
 294 
Rear fog light jointLeft rear fog light
Bulb