wheel alignment GEELY FC 2008 Workshop Manual

Replacement...................................................
72
Coolant.................................................................
73
Replacement...................................................
73
Lubrication
Lubricating system...............................................
74
On-vehicle inspection......................................
74
Oil filter assembly.................................................
75
Replacement....................................................
75
Oil pump assembly...............................................
76
Replacement....................................................
76
Ignition
Ignition system.....................................................
77
Inspection........................................................
77
On-vehicle inspection......................................
77
Starting and charging
Starting system.....................................................
79
Inspection........................................................
79
Charging system..................................................
81
Precautions......................................................
81
On-vehicle inspection......................................
82
Alternator components..............................................
84
Replacement....................................................
84
Starter components..............................................
85
Replacement....................................................
85
Front suspension
Front suspension system....................................
86
Table on trouble occurrence...........................
86
Front wheel alignment.........................................
87
Adjustment......................................................
87
Front absorber and helical spring.......................
90
Overhaul..........................................................
90
Handling..........................................................
93
Lower left control arm assembly.........................
94
Replacement...................................................
94Front stabilizer bar...............................................
96
Overhaul..........................................................
96
Front left lower control arm ball joint assembly
..
99
Replacement...................................................
99
Rear suspension
Rear suspension system....................................
100
Table on trouble occurrence..........................
100
Rear wheel alignment.........................................
101
Adjustment.....................................................
101
Rear strut assembly...........................................
102
Overhaul........................................................
102
Handling.........................................................
104
Rear stabilizer bar..............................................
105
Overhaul........................................................
105
Rear shaft assembly...........................................
106
Overhaul........................................................
106
Tire and wheel
Wheel and tire system.......................................
109
Inspection......................................................
109
Drive shaft
Drive shaft.......................................................
111
Notes.............................................................
111
Malfunction phenomenon table....................
111
Inspection on automobile.............................
11 2
Front drive shaft.................................................
11 3
Overhaul........................................................
11 3
Left front shaft hub assembly............................
123
Change..........................................................
123
Left front shaft hub bolt......................................
128
Change..........................................................
128
Left rear shaft hub and bearing assembly........
129
Change..........................................................
129
Left rear shaft hub bolt.......................................
131
Change..........................................................
131

Brief introduction on Geely model “FC”Basic parametersTable 1 Complete vehicle basic parametersUnit
Item nameNumber
Dimension parametersOverall
dimension
Wheel trackLength
Width
Height
Front wheel
Rear wheel
Wheel base
Front suspension
Rear suspensionPassenger numberPersonParameters±15±15±20±10±10±30±30Left lamp
Right lamp
Left lamp
Right lampLeft and
right
inclination
Down
inclinationComplete vehicle herb massMax. total massFront axle
Rear axle
Front axle
Rear axle
Weight distributionNo
load
Full
loadMin. turning diameter
Min. gound clearance
Approach angle (full load) Departure angle (full load)Front wheel camber
Kingpin inclination angle
caster angleConvergence of front wheelsRear wheel camberConvergence of rear wheelsLeft wheel: inside/outside
Right wheel:inside/outside CanderaBrief introduction on Geely model “FC” Basic parameters
Mass parameters
Traverse ability
Front wheel alignment
parameters
Rear wheel
alignment
parameters Front wheel
steering
wheel
Head lamp light
High beam
optical axisLuminous intensity of
high beam of head lamp1

Engine mechanism - Engine assembly85. Install alternator mounting components.Torque: 12mm bolt head A: 14mm bolt head B: 86. Install drive belt.
87. Install engine wire harness and all hoses
not connected.(a) Check and connect all joints of engine wire harness.
(b) Check and connect all hoses.88. Install transmission control pull cable assembly
and valve control pull cable.
89. Install air filter assembly and its hose.
90. Install steering middle shaft assembly.(a) Align alignment mark on steering middle shaft.
(b) Install 2 bolts.
Torque: m
(c) Install steering column cover.91. Install front exhaust pipe assembly.
92. Install front chassis bracket.Torque: 93. Install battery and connect wire.
94. Install engine plastic hood components.
95. Install front wheel and engine bottom shield.
96. Refill transmission lubricant.
97. Refill engine oil.
98. Refill coolant.
99. Check there is oil leakage.
100. Check there is coolant leakage.
101. Check idle speed and ignition timing.
102. Check CO/HC.Alignment
mark
Sliding in
Pulling 44

Front suspension - front suspension systemFront suspensionFront suspension systemTable on trouble occurrenceThis table could help you find out failure causes, and each figure in the table indicates the possible
sequence of failure causes, please check every part as the sequence, and replace if necessary.Trouble occurrence Possible trouble part Pages to refer to
1. Tire (abrasion or improper tire pressure) 109
2. Wheel alignment (incorrect) 87
Deflection/single side 3. Steering linkage (looseness or abrasion) -
4. Shaft hub bearing (abrasion) 123
5. Suspension parts (abrasion) -
6. Steering gear (poor adjustment or breakage) -
1. Vehicle (overload) -
Bottoming 2. Spring (elastic fatigue) 90
3. Absorber (abrasion) 90
1. Tire (abrasion or improper tire pressure) 109
Swaying left and right/ 2. Stabilizer bar (bending or breakage) 96shaking forward and backward3. Absorber (abrasion) 90
1. Tire (abrasion or improper tire pressure) 109
2. Wheel (poor balance) 109
3. Absorber (abrasion) 90
Front wheel shimmy 4. Wheel alignment (incorrect) 87
5. Ball joint (abrasion) 99
6. Shaft hub bearing (looseness or abrasion) 123
7. Steering linkage (looseness or abrasion) -
8. Steering gear (poor adjustment or breakage) -
1. Tire (abrasion or improper tire pressure) 109
Abnormal tire abrasion 2. Wheel alignment (incorrect) 87
3. Absorber(abrasion) 90
4. Suspension parts (abrasion) -86

Front suspension - Front wheel alignmentFrontRearIf toe-in is not within specification, please adjust left and
right levers of steering gear.4. Adjustment of toe-in(a) Remove dust cover fixing clip.FrontRearToe-in(Total)Front wheel alignmentAdjustment1. Inspection(a) Check tire is worn and inflation pressure is proper.
Tire inflation pressure under normal temperature:Tire size Front and rear kPa*1 It is used under the condition of speed below 160 km/h.
*2 It is used under the condition of speed above 160 km/h.
(b) Check tire run-out with dial indicator.
Tire run-out: 3.0mm.2. Measurement of vehicle heightVehicle height:
(General road)
(Coarse road)
Measuring point:
A. Height for ground and front wheel center
B. Height for ground and bolt center in front of lower
control arm
C. Height for ground and fixed bolt center of rear axle beam
D. Height for ground and rear wheel center
Note: adjust vehicle height to standard value before checking front wheel alignment.
If vehicle height does not conform to regulations, please shake upward and downward or lift vehicle
body to adjust vehicle height.3. Inspection of toe-inToe-in:Front87

Inside wheel38o452oOutside wheel: reference32o50Front suspension - Front wheel alignment(Coarse road)
Inside wheel39o052oOutside wheel: reference33o10Camber-031’45’Left-right error45’Caster242’45’Left-right error45’Steering shaft inclination18’45’Left-right error45’Camber-
018’45’Left-right error45’Caster230’45’Left-right error45’Steering shaft inclination1052’45’Left-right error45’A: inside
B: outsideFrontGauge If caster and steering axis inclination are not within specification, please adjust the caster and
then check parts of lower control arm is damaged or worn.(b) Loosen lock nuts at the end of transversal lever .
(c) Evenly rotate end levers of left and right rack to
adjust toe-in.
Hint: try adjusting toe-in to medium value.
(d) Ensure that the end lever length of left rack equals that
of right rack.
(e) Tighten lock nuts at the end of transversal lever.
Torque: 745 N.m
(f) Install dust cover fixing clip.
Hint: ensure that the dust cover does not distort.5. Inspection of turning angle(a) Completely rotate steering wheel to the bottom and then
measure turning angle.
Turning angle:
(General road)
(Coarse road)Wheel
alignment
tester88If left and right inside wheels are not within specification, please check the end lever length of left rack
and right rack.6. Inspection of camber, caster and steering shaft inclination(a) Install camber-caster-kingpin gauge or erect wheel alignment tester.
(b) Check camber, caster and steering-axis inclination.
Camber, caster and steering shaft inclination:
(General road)

Front suspension - Front wheel alignment7. Adjustment of camberNote: after adjusting the camber, please check toe-in.
(a) Remove front wheels.
(b) Remove 2 nuts under absorber.
If it is necessary to repeat using bolts or nuts, please coat
oil to thread of nuts.
(c) Clean nut absorber and attachment face of steering knucle.
(d) Temporarily install 2 nuts.
(e) Push or pull lower end of absorber in the direction that cam-
ber requires adjustment to adjust the camber.
(f) Tighten nut.
Torque: 15310 N.m
(g) Install front wheels.
Torque: 10310 N.m
(h) Check camber.89

Front suspension - Front shock absorber and helical springHandling1. Handle front left absorber assembly.(a) Completely pull out absorber piston rod.
(b) As shown in the diagram, drill a small hole on cylinder body
between two lines with electric drill to make inside gas flow
out
Notes:Iron chip may fly out during drilling, please be care-
ful in operating.The gas is colorless, odorless and nontoxic.93(c) Install 2 nuts to lower end of absorber.
Torque: 15310 N.m
Hint: coat oil on thread of nuts.
(d) Install brake hose and ABS speed sensor wire harness
bracket with bolts.
Torque: 19N.m9. Install front left stabilizer link assembly [64000097].Install stabilizer link with nuts.
Torque: 745 N.m
Hint: if ball joint rotates with nuts, please fix bolts with
hexagonal wrench (6mm).10. Install front wheels.Torque: 10310 N.m11. Check and adjust front wheel alignment
(see Page 87).

17. Install front left brake wheel pump bracket as-
sembly (see Page 141).
18. Install fixed nuts of front left drive shaft (see
Page 123).
19. Install front left stabilizer link assembly
[64000097].Install stabilizer link with nuts.
Torque: 745 N.m
Hint: if ball joint rotates with nuts, please fix bolts with
hex wrench (6mm).20. Install front right stabilizer link assembly
[64000097].Hint: the installation procedures of right side are the
same as that of left side.21. Align suspension.(a) Install front wheels and lay down vehicle from the lift.
Torque: 10310 N.m
(b) Align suspension components by means of lifting ve-
hicle several times.22. Completely lock up lower left control arm assem-
bly [64000091].Completely tighten 2 bolts and nuts.
Torque: 13710 N.m23. Check and adjust front wheel alignment
(see Page 87).
24. Check ABS sensor signal.Front suspension - Lower left control arm assembly95

30. Connect steering sliding shaft (see Page 205).
31. Check front wheel center line.
32. Install dust cover inside steering column.
33. Refill power steering oil (see Page 200).
34. Discharge air of power steering oil (see Page 200).
35. Check there is oil leakage.
36. Check and adjust front wheel alignment (see Page 87).Front suspension - Front stabilizer bar98