width GEELY FC 2008 Workshop Manual

Brief introduction on Geely model “FC”Basic parametersTable 1 Complete vehicle basic parametersUnit
Item nameNumber
Dimension parametersOverall
dimension
Wheel trackLength
Width
Height
Front wheel
Rear wheel
Wheel base
Front suspension
Rear suspensionPassenger numberPersonParameters±15±15±20±10±10±30±30Left lamp
Right lamp
Left lamp
Right lampLeft and
right
inclination
Down
inclinationComplete vehicle herb massMax. total massFront axle
Rear axle
Front axle
Rear axle
Weight distributionNo
load
Full
loadMin. turning diameter
Min. gound clearance
Approach angle (full load) Departure angle (full load)Front wheel camber
Kingpin inclination angle
caster angleConvergence of front wheelsRear wheel camberConvergence of rear wheelsLeft wheel: inside/outside
Right wheel:inside/outside CanderaBrief introduction on Geely model “FC” Basic parameters
Mass parameters
Traverse ability
Front wheel alignment
parameters
Rear wheel
alignment
parameters Front wheel
steering
wheel
Head lamp light
High beam
optical axisLuminous intensity of
high beam of head lamp1

Engine mechanism - Timing chain assembly30. Install crankshaft front oil seal assembly.(a) Coat a little MP grease on oil seal lip.
(b) Gently knock new oil seal in with special tool and ham-
mer until the seal surface is parallel and level with the
edge of timing chain cover.
Note: do not let oil seal mouth contact with foreign
matters.31. Install timing chain hood components.(a) Eliminate all old seal materials from contact surface.
(b) As shown in the diagram, coat sealant on the edge
(diameter 3.5mm-4.5mm).
Sealant: silicon rubber flange sealant 1596 (Kesaixin
1596).
(c) Install timing chain hood with 12 bolts and nuts.
Torque: Notes:Eliminate all grease on contact surface.After coating sealant, finish installation of timing chain
hood within 3 minutes.After installing, do not refill engine oil within 2 minutes.32. Install chain tensioner components.(a) Check o-ring is clean, and buckle on the hook as shown
in the diagram.Special
tool 48 SealantSealant widthChain cover
groove
Cylinder
head groove Sealant
concentrationEntering
Hook
PinLifting

(3) Fix the module on wheel.
a. Assemble three bolts with gasket on two assembling
holes of left, middle and right support pin of safety airbag
module at the side of passenger.
Size of bolt: L 35.0 mm
M 8.0 mm
Note: screw the bolts with hand, but they could not
be screwed too tightly, 2/3 L of bolts should
expose.
2. Explosion of safety airbag assembly at the side of passenger.
(1) Prepare a battery as detonating power (12±1)V.
(2) Disassemble safety airbag assembly at the side of passenger, and connect the airbag short wiring
harness on gas generator.
Warning: when storing safety airbag module at the side of driver, it is necessary to keep upper
surface face upwards.
Supplemental restraint system--Scrap treatment for safety airbag
Old tire
without hud
Wiring harness
for explosion
Wiring harness
for explosion
Left and
right small
bracket
 267 
(5) Fix three scraped old tyres without wheel hub on the fixed
tyre of safety airbag assembly at the side of driver. The
terminal end of unfolding wiring harness is 10m apart from
wheel of fixed airbag at least.
Width: 185mm
Inner diameter: 360mm
(6) Cut off the joint of wiring harness used for unfolding of safety
airbag assembly at the side of driver at the place apart from
the automobile, then connect it with two ends of battery.
(7) Treatment for explosive module.
Disassemble the safety airbag module at the side of driver
from wheel, and put it in ethane plastic bag, then bind the
bag for treatment with other parts.

Supplemental restraint system--Scrap treatment for safety airbag
Special
tool
Safety airbag
assembly at the
side of passengerBattery
Over 10m
(5) Put two tyres at least under the tyre fixed with airbag
assembly, and put two tyres at least on the tyre fixed with
airbag assembly, at the same time, top tyre should have
wheel hub. Use two wiring harnesses to bind tyre tightly, if
shake is produced when airbag explodes, airbag module
will break off to make danger.
Width: 185mm
Inner diameter: 360mm
(6) Cut off the joint of wiring harness used for unfolding of safety
airbag assembly at the side of driver at the place apart from
the automobile, then connect it with two ends of battery.
(7) Treatment for explosive module.
Disassemble the safety airbag module at the side of driver
from wheel, and put it in ethane plastic bag, then bind the
bag for treatment with other parts.
 269