transmission oil GEELY MK 2008 Owner's Manual

9. Pull out oil seal (on the transaxle housing) with a special tool.
(See Fig.7-10)
10. Remove the differential front oil seal on the transmission housing.
Pull out the oil seal on the transmission housing with a special
tool. (See Fig.7-11)
11. Install the differential front oil seal onto the transmission housing.
(1) Install a new oil seal on the transmission housing with a
special tool and hammer. (See Fig.7-12)
(2) Apply MP lube on the flange of the oil seal.
12. Install the differential front oil seal onto the transmission housing.
(1) Install a new oil seal onto the transmission housing with a
special tool and hammer. (See Fig.7-13)
(2) Apply MP lube on the flange of the oil seal.Figure 7-10
Figure 7-11
Figure 7-12Figure 7-13Automatic Transaxle Assembly Differential Front Oil Seal (ATM)3-3413. Install all parts in the sequence of removal till the front wheel is installed, and then add transmission oil.
14. Check and adjust the alignment of the front wheel. -

Overhaul1. Drain manual transmission oil (M/T transmission)
Torque: 39N.m
2. Drain automatic transmission oil (A/T transmission)
Torque: 25N.m
3. Remove front wheel
4. Remove engine bottom left shield (M/T transaxle)
5. Remove engine bottom right shield (M/T transaxle)
6. Remove engine bottom shield assembly (A/T transaxle)
7. Remove front wheel hub left bolt
(1) Using a hammer and a drive shaft nut chisel, unstake the
staked part of the left wheel hub nut.
(2) While applying the brake pedal, remove the left wheel hub
nut.
Notice: the staked part of the nut should be fully unstaked,
otherwise it may damage the thread of the drive shaft.
8. Remove left front vehicle speed sensor (with ABS)
(1) Remove the bolt and clip, remove vehicle speed sensor and
brake hose from left front shock absorber assembly.
(2) Remove the bolt, separate the left front vehicle speed sensor
from steering knuckle.
9. Remove front stabilizer bar
(1) Use a 10mm wrench to hold the bolt, remove the nut
(2) Remove two collars, No.1 and No.2 gaskets, remove front
stabilizer barPropeller Shaft/DriveshaftFront Driveshaft4-21 -

Propeller Shaft/DriveshaftFront Driveshaft4-28 Hint:
Please refer to the following table for dimension (A).LH mm
528.3±5.0
527.0±5.0RH mm
859.3±5.0
860.0±5.0 M/T manual transmission
A/T automatic transmission38. Install left constant velocity drive shaft assembly
(1) M/T
Coat the spline of the tripod joint assembly with gear oil.
(2) A/T
Coat the spline of the tripod joint assembly with ATF
(Automatic Transmission Fluid).
(3) Align the spline, use a brass bar and hammer to install the left
drive shaft assembly.
Notice:
Face the retainer open end downward.
Be careful not to damage the boot and oil seal.
Hint:
You can find out whether the tripod joint shaft contact the pinion shaft by rotating the shaft assembly, listening
to the sound and feeling.
39. Install right constant velocity drive shaft assembly
Hint:
The installation of the right side is the same as that of the left side.
Notice:

Install the retainer with its open end facing downward.
Be careful not to damage the boot and oil seal.
40. Install left steering knuckle assembly
Install the left constant velocity drive shaft assembly on the left steering knuckle assembly.
Notice:
Be careful not to damage the outboard joint boot.

With ABS:
Be careful not to damage the vehicle speed sensor rotor.
41. Install left steering gear with tie rod assembly
(1) Install the steering gear with tie rod assembly on the steering knuckle assembly with nuts.
Torque: 33N.m
(2) Install the new cotter pins.
Notice:
If the pin holes are not aligned, further tighten the nut by 60°.
42. Install left lower swing arm assembly
(1) Install the left lower swing arm assembly on the steering knuckle assembly with nuts.
Torque: 98N.m -

Propeller Shaft/DriveshaftFront Driveshaft4-29 (2) Install the new cotter pins.
Notice:
If the pin holes are not aligned, further tighten the nut by 60°.
43. Install front stabilizer bar
(1) As shown in the illustration, install the stabilizer bar with two
No.1 collars and two gaskets and nuts.
Notice:
Make sure the gaskets and collars are correctly installed.
(2) Tighten the nut with a 10mm wrench.
Torque: 18N.m
44. Install left front vehicle speed sensor (with ABS)
(1) Install the left front vehicle speed sensor and brake hose on the
front shock absorber with bolts and clps.
Torque: 29N.m
(2) Install the vehicle speed sensor on the steering knuckle with
bolts.
Torque: 8.0N.m
Notice:
Be careful not to damage the wheel speed sensor.

Keep the vehicle speed sensor clean.
When installing the sensor,do not twist the sensor wire harness.
45. Install left steering knuckle wheel hub nut
(1) Install new left steering knuckle hub nuts
Torque: 216N.m
(2) Using a chisel and hammer, stake the hub locking nut.
46. Install engine bottom left shield
47. Install engine bottom right shield
48. Install engine bottom shield assembly
49. Install front wheel
Torque: 103 N.m
50. Add oil into manual transmission
51. Check and adjust the manual transmission fluid
52. Refill automatic transmission fluid
53. Check and adjust the automatic transmission fluid
54. Check and adjust front wheel alignment
55. Check ABS vehicle speed signal (with ABS) -

19151915131515
Fluid level indicator lamp connectorVacuum booster assembly
Gasket25Clip26 Clip Master cylinder
Manual Transmission
#1 clutch fluid tank oil pipe
HECU assemblyClipSection 5 Vacuum BoosterComponent ViewBrake System -Vacuum Booster4-91Battery
#2 relay box, engine chamber
Return spring
Pin
Push bar
U-connector Without ABSVacuum tube
Non-reusable parts
Lithium soap base glycol lubeSpecified torque

26LH/RH rear brake pipe component II x rear brake hose assy.Null13~18 13~18
27 front suspension cross member (front part) x bodyJQ1401280TF2(2 pcs)94~110 94~110
28 Front suspension cross member (rear part) x bodyJQ1401455TF2(2 pcs)110~130 110~130
29 Engine right mount x right insulator JQ319B10(1 pcs)49~60 49~60
30 Engine left mount x left insulator JQ184C1030(2 pcs)43~58 43~58
31 Engine left LH x bodyJQ184B12140(1 pcs)94~110 94~110
32 Engine x automatic transmissionJQ140BD1255TF2(2 pcs)/ 55~70
33 Engine x automatic transmissionJQ140BD1260TF2(1 pcs)/ 55~70
34 Engine x automatic transmissionJQ140C1040TF2(1 pcs)/ 43~58
35 Engine x automatic transmission JQ140C1020(3 pcs) /43~58
36 Engine x automatic transmissionJQ140BD1255TF2(2 pcs)55~70 /
37 Engine x automatic transmissionJQ140BD1045TF2(1 pcs)43~58 /
38 Engine x automatic transmissionJQ140C1040TF2(1 pcs)43~58 /
39 Engine x automatic transmission JQ140C0820(3 pcs)22~29 /
40 Starter x transmissionJQ146C1040TF2(2 pcs)30~60 30~60
41 Engine left bracket x transmission JQ184C1030(3 pcs)43~58 43~58
42 Engine rear bracket x engine JQ184C1025(2 pcs)43~58 43~58
43 Engine rear bracket x engine JQ184C1020(1 pcs)43~58 43~58
44 Compressor bracket x engine JQ146C1035(1 pcs)43~58 43~58
45 Compressor bracket x engine JQ146C1030(3 pcs)43~58 43~58
46Power steering pump with bracket assy. (without reservoir) x engineQ1420825(3 pcs)22~29 22~29
47Power steering pump with bracket assy. (without reservoir) x engineQ14201030(1 pcs)43~58 43~58
48 Oil pump adjustment bracket x engine JQ146C1030(2 pcs)43~58 43~58
49Oil pump adjustment bracket x power steering pump
JQ146C1030(1 pcs)43~58 43~58
with bracket assy. (without reservoir)
50Oil pump mounting bracket x power steering pump with
JQ142C1085(2 pcs)43~58 43~58
bracket assy. (without reservoir)
51Oil pump mounting bracket x power steering pump with
Q40110(1 pcs)43~58 43~58
bracket assy. (without reservoir)
52Oil pump mounting bracket x power steering pump with
Q361C10(1 pcs)43~58 43~58
bracket assy. (without reservoir)
53 Rear insulator x front suspension cross member JQ184C1060(1 pcs)43~65 43~65Appendix-Torque Table of the Fasteners for Important AssemblyIITorque N.m
No.
JL7132HU
JL7152HUJL7132U
JL7152U
JL7162U Area FastenerAppendix: Torque Table of the Fasteners for Important Assembly