oil GEELY MK 2008 Repair Manual

19151915131515
Fluid level indicator lamp connectorVacuum booster assembly
Gasket25Clip26 Clip Master cylinder
Manual Transmission
#1 clutch fluid tank oil pipe
HECU assemblyClipSection 5 Vacuum BoosterComponent ViewBrake System -Vacuum Booster4-91Battery
#2 relay box, engine chamber
Return spring
Pin
Push bar
U-connector Without ABSVacuum tube
Non-reusable parts
Lithium soap base glycol lubeSpecified torque

Brake System -Front Brake Disc4-94Component ViewSection 6 Front Brake Disc34Front disc brake pistonSet ring Dust shield Piston oil seal Left front disc
brake cylinder accessory3483088Connector bolt
Washer
Discharge screw
plug capTubeDust shield Front disc brake
cylinder sliding pin
#2 muffle pad
#1 muffle pad
Brake pad
Brake pad#1 muffle pad
#2 muffle pad
Support piece
Front brake pad ISupport piece
Front brake pad IIFront disc brake cylinder
sliding pin88Dust shield
Left cylinder support
Non-reusable parts
Lithium soap base glycol lube
Disc brake lubespecified torqueN.
m :

Brake System -Front Brake Disc4-9611. Remove the front brake piston.
(1) Put a piece of cloth or equivalent between the brake cylinder
and the piston.
(2) Blow the piston out of the brake cylinder with compressed air.
Warning:
In the blowing process, the finger shall not be placed before the
piston.
Note:
Don't spray the brake fluid.
12. Remove the piston oil seal.
Take out the oil seal from the brake cylinder with screwdriver.
13. Check the brake cylinder and piston.
Check the cylinder wall and piston whether there is rust or scar.
14. Check the lining thickness of the brake pad.
Measure the lining thickness with ruler.
Standard Thickness: 10.0mm
Minimum Thickness:1.0mm
15. Check the abrasion indicator steel strap of the front brake.
Make sure the abrasion indicator steel strap has adequate flexibility and has no deformation, crack or damage.
All rust, dirt and other impurities shall be cleaned out.
16. Check the thickness of the brake disc.
Measure the thickness of the brake disc with screw micrometer.
Standard Thickness: 20.0mm
Minimum Thickness: 18.0mm
17. Remove the front brake disc.
(1) Make mark on the brake disc and wheel hub.
(2) Remove the brake disc.
18. Install the brake disc.
Tips:
Install the disc at the minimum swing position.

Brake System -Front Brake Disc4-9719. Check the swing of the brake disc.
(1) Fasten the brake disc temporarily.
Torque: 103N.m
(2) Measure the swing of the brake disc at the 10mm from the disc
edge with a dial test indicator.
Maximum Swing: 0.05 mm
(3) If the swing of the brake disc reaches or exceeds the limit,
check the bearing's axial clearance and the wheel hub's swing.
If the bearing and wheel hub run normally, adjust the swing
of the brake disc, or finish it with onboard finishing machine.
20. Tighten the brake discharge bolt temporarily.
Tighten the brake discharge screw plug on the front brake cylinder temporarily.
21. Install the piston oil seal.
(1) Apply the lithium soap-base glycol lube on the new piston oil seal.
(2) Install the new piston oil seal on the brake cylinder.
22. Install the brake piston.
(1) Apply the lithium soap-base glycol lube on the brake piston.
(2) Install the piston on the front disc brake cylinder.
Note:
Don't tighten the piston into the brake cylinder forcefully.
23. Install the dust shield of the brake wheel cylinder.
(1) Apply the lithium soap-base glycol lube on the dust shield of
the new brake wheel cylinder, and install it on the brake
cylinder.
Tips:
Install the dust shield in the groove of the brake wheel cylinder
and piston reliably.
(2) Install the set ring with screwdriver.
Note:
Be careful not to damage to the dust shield of the brake wheel cylinder.
24. Install the left front disc brake wheel cylinder support.
Fasten the front disc brake wheel cylinder support with two blots.
Torque: 88N.m
25. Install the dust shield of the front disc brake bushing.
Apply the lithium soap-base glycol lube on the surface of the two new dust shields.
Install the two dust shields on the front disc brake cylinder support.
26. Install the sliding pin of the front dist brake cylinder.
Apply the lithium soap-base glycol lube on the surface of the two sliding pin and oil seal.
Install the two sliding pins on the front disc brake cylinder support.

Brake System -Front Brake Disc4-9827. Install the support piece of the front brake pad.
Remove the two support pieces of the brake pad from the front disc brake cylinder support.
28. Install the brake lining block component.
Note:
When replace the abrasion brake lining block, replace the muffle
pad simultaneously.
(1) Apply the disc brake lube on both sides of all muffle pads
(2) Install muffle pads on all brake lining blocks.
(3) The abrasion indicator face upwards. Install a inner brake
lining block, then install a outer lining block.
Note:
Don't apply the oil or lube on the friction surface of the brake pad and brake disc.
29. Install the front disc brake wheel cylinder.
(1) Install the front disc brake wheel cylinder with two bolts.
Torque: 34N.m
(2) Install the new washer and tube with bolt.
Torque: 30N.m
Tips: Fasten the tube in the lock hole of the brake wheel
cylinder reliably.
30. Add the brake fluid to the storage tank.
31. Discharge the air in the brake cylinder.
32. Discharge the air in the brake pipeline.
33. Check the level height in the storage tank.
34. Check the brake fluid whether there is any leakage.
35. Install the front wheel.
Torque: 103N.m

Brake System -Rear Brake Drum4-10213. Check the brake shoe and the brake shoe lining whether they
touch normally.
Mark the inner surface of the brake drum with chalk, joint and
abrade the brake shoe and the inner surface.
If the drum and the lining touch poorly, abrade the brake shoe or
replace a new one.
14. Remove the left front or top brake wheel cylinder.
(1) Unfix the brake oil pipe with a special tool, and collect the
brake fluid with a container.
(2) Remove the bolt and brake wheel cylinder.
15. Remove the brake cup.
(1) Remove the two dust shields from the brake cylinder.
(2) Remove the two pistons and springs.
(3) Remove the two brake cylinder caps from every piston.
16. Check the brake cylinder.
Check the cylinder wall and piston whether there is any rust or nick.
17. Remove the rear discharge screw plug of the brake drum.
18. Tighten the rear discharge screw plug of the brake drum
temporarily.
19. Install the brake wheel cylinder cup.
(1) Apply the lithium soap-base glycol lube on the two brake
wheel cylinder cups and the piston.
(2) Install two brake cylinder caps on every piston.
(3) Install the compression spring and the two pistons on the
brake wheel cylinder.
(4) Install two new dust shields on the brake wheel cylinder.
20. Install the left front or top brake cylinder.
(1) Install the brake cylinder with bolt.
Torque: 9.8N.m
(2) Connect the brake oil pipe with a special tool.
Torque: 15N.m
21. Apply the heat-resistant lube.
Apply the heat-resistant lube on the touch surface of the brake
backboard and the brake shoe.

Brake System -Rear Brake Drum4-105 (2) Measure the inner diameter of the brake drum and the
diameter of the brake shoe, and check the difference of them
whether it is a proper brake shoe clearance.
Brake Shoe Clearance: 0.3mm
Note:
Don't apply the oil or lube on the friction surface of the brake shoe
lining and brake drum.
30. Adjust the shoe clearance of the brake drum.
(1) Install two wheel hub nuts temporarily.
(2) Turn around eight teeth of the adjustor.
(3) Install the hole plug.
31. Install the rear brake drum sub-assembly.
32. Add the brake fluid to the storage tank.
33. Discharge the air in the master cylinder.
34. Discharge the air in the brake pipeline.
35. Check the level height in the storage tank.
36. Check the brake fluid whether there is any leakage.
37. Install the rear wheel.
Torque: 103N.m
38. Check the stroke of the parking brake extension rod.
39. Adjust he stroke of the parking brake extension rod.Extend

Part V Electric System & AccessoryChapter 1 Starting and Charging SystemSection 1 Starting System (MR479Q MR479QA MR481QA)I. Starter inspectionNote:
These tests must be completed within 5s, so as to prevent coil from burning out.
1. Electromagnetic switch testElectric System & Accessory-Starting and Charging System5-1 (1) As shown in the figure, use wire to connect starter.
(2) As shown in the figure, connect electromagnetic switch with
storage battery.
(3) Disconnect exciting coil from binding post A.
(4) Check whether clutch pinion moves outboard.
If clutch pinion does not move, replace electromagnetic switch.
(5) As shown above, connect battery, disconnect positive
pole (+) of battery from binding post, disengage
clutch pinion.
(6) Check whether clutch pinion returns.
If clutch pinion does not return, replace electromagnetic switch.
2. Starter no-load test
(1)Connect field coil and binding post.
(2) As shown in the figure, connect ammeter and battery
to starter.
(3) When check whether clutch pinion moves outwards, starter
should rotate slowly and smoothly.
(4) Check whether current reading of ammeter is normal or not.
Normal current: less than 90 A at 11. 5 V
If current is abnormal, replace starter.Ammeter Battery
Terminal 50
Terminal 30Disconnect
BatteryBatteryTerminal C
Terminal 50

3. Definition of multi-pin plug-in unit terminal
1. Prompt:
R- red Bl- blue Y - yellow B- black P- pink G- green W- white
O- orange Gr - gray Br- brown V- purple Lg- olive drab
The first letter indicates primary color
The second letter indicates stripe colorTerminal
number1 MIL C 10 NA
2 Engine oil pressure switch YG 1 P
3 Brake fluid GR 2 R
4 Park G 3 N
5 Right turn light GB 4 D
6NA 52
7 EBD 6 L
8 Charge WR 7
9NA 8NA
10 NA 9 Sidelight GW
11 Safety belt YR 10 Start BR
12 NA 11 B+
13 Engine GY 12IG ( + ) Y
14 Safety gasbag RY 13 GND
15 NA 14 NA
16 IG ( + ) 15Speed sensor earthing B
1 NA 16 Speed signal input YR
2 Left turn light GW 17 Speed sensor power supply RY
3 High beam (+) RB 18 Key (ODO/TRIP) G
4 High beam (-) RW 19 Key (adjust brightness) YG
5 Foglight Gr 20 Key COM B
6 Rear defrost YB 21 Fuel gauge V
7 NA 22 ABS R
8 NA 23 Tachometer BBL
9 Door-lock warning lamp RBL 24 Coolant temperature gauge YWA
BCCombination Instrument System -Wiring diagram of Combination Instrument and Location of Multi-pin Plug-in Terminal5-9Definition of terminalConductor
ColorTerminal
numberDefinition of terminalConductor
Color

Note:
To measure, disconnect the connector.
5. Check water thermometer
(1) Check resistance
When water thermometer indicates water temperature to red area, check the resistance between C24
terminal and C13 terminal on combination instrument connector.
Standard 4. Check fuel gauge
(1) Check resistance
Check resistance between C21 terminal and C13 terminal on combination instrument connector.
Standard:5-19Standard indication
E
Reminder point
1/2F
FResistance (ohm)
104-116
90-100
29-35
1-5
Standard indication
C
1/2H
Alarm point
HResistance (ohm)
159. 5-169. 5
53-59
26. 7-30. 7
20-24
Note:
To measure, disconnect the connector.
6. Check water temperature warning lamp
(1) Disconnect water temperature sensor connector.
(2) Turn ignition switch to ON, water temperature warning lamp should go out.
(3) Ground instrument connector C24 terminal, water temperature warning lamp should illuminate.
7. Check engine oil pressure warning lamp
Disconnect engine oil pressure transducer connector.
Turn ignition switch to ON, engine oil pressure warning lamp should go out.
Use conductor to short connector terminal to earth, engine oil low pressure warning light should illuminate.
8. Check engine oil pressure transducer
Disconnect connector from engine oil pressure transducer
Check connection between terminal and ground
Engine stall: on state
Engine running: off state.Combination Instrument System -Malfunction Symptom Table and Troubleshooting