spare wheel GEELY MK 2008 Workshop Manual

Table 3 Power Performance Parameter
Table 4 Economic Performance ParameterUnit
km/h
s
s
km/h
% Item Name
Maximum vehicle speedAcceleration time within the fourth gear from 30km/h to 120km/hAcceleration time from 0-100km/hMinimum stable vehicle speed within the fourth gearMaximum gradeability No.
1
2
3
4
5Unit
L/100km
L/100km
m Item Name
Fuel consumption at constant speed (60km/h)
Fuel consumption at constant speed (90km/h)Coasting distance (fully loaded, initial speed 50km/h)No.
1
2
3JL7132U JL7152U JL7162UJL7132HU JL7152HU


/JL7132U JL7152U JL7162UJL7132HU JL7152HU
4.5
550Brief Introduction of Geely MK - Vehicle Configuration2-3Section 2 Vehicle ConfigurationType
Common color
Uncommon color
Exterior
device
Seat Interior
deviceItem NameNo.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19Standard Comfortable Luxury
Firry red Firry red
Titanium silver Body colorChinese red, snow mountain white, pearl black, sky blue, ribbon silver
Crystal diamond silver, golden sand green, pineapple yellowFront chromeplated trim molding
Diamond-shape headlight
Crystal diamond taillight
Highly penetrable front fog light
Green heat insulating four-door glass
Scuff strip with same color as that of the body
Aluminum alloy wheel rim
Tire (185/60R15) (with spare tire)
Retractive antenna (A pillar)
Bumper with same color as that of the bodyLight color (T)deep color(S)mixed color(R)interior trimCentral control panel
A/C outlet vent + trim ring
Chromeplated inner handle
Sun shade (with ticket folder)
High-grade flannelette
Luxury leatherFront seat headrest front and rear angle/height adjustable function
/ /
20
2522
16.5 18
20165
33
28 30155 175 165 155
306.25.1
4.65.0
4.7
6.7
6.36.6 6.2
550 550
550 550 / /
/ / / /

Charpter 7 WheelSection 1 Tire Inspection and Wheel ReplacementCheck1. Check tire
(1) Check appearance of tire and its pressure
Cool tire pressure: (2) Check the runout of tire by dial indicator
Runout of tire: less than 3.0mm
2. Tire replacement
Notes: As showed in graphic, replacement position of every tire
including and not including the spare tire.
3.Check tire dynamic balance
(1) Check and adjust wheel on the tire dynamic machine beside
vehicle
(2) Check and adjust wheel on the tire dynamic machine loaded
beside vehicle
Balance deviation after adjustment: less than 8.0g.
4. Check bearing gap
5. Check hub deviation.Tire size
175/65 R14 82H
185/60 R15 84HFront
(KPa)
230Rear
(KPa)
210Wheel-Tire Inspection and Wheel Replacement4-66Front

Section3 Removal and InstallationI. Precautions for removal and installation1. Firstly use diagnostic instrument to find out source of trouble, then repair.
2. Repair front prior use excluding mineral oil of detergent will surface clean Neatness ; repair when should note
before repair, use detergent without mineral oil to wipe off surface; pay attention to cleaning during repair, only
use rag without wool to wipe removed components.
3. Only use original factory spare parts, and new spare parts could only be unpacked just before installation.
4. Return liquid pump motor and hydraulic controller (HCU) is integrated structure, can not be separated.MK-60 ABS system -ABS System Check/ Removal and Installation5-116 d. Rotate the wheel at speed of about 1 / 2 turns per second, use multimeter or oscillograph to measure output
voltage
Terminal 45-46
Terminal 33-34
Terminal 37-36
Terminal 42-43
Output voltage

When use multimeter for measurement
See front wheel sensor drawing for front wheel.
See rear wheel sensor drawing for rear wheel

When use oscillograph for measurement
See relevant standard for front wheel.
See relevant standard for rear wheel.
e. If output voltage is not in above-mentioned range, the cause might be the following:

Air gap between sensor and pulse ring is too large.

Sensor fails.

Check sensor resistance value (1. 0 - 1. 3 k ohm).

Take four points on pulse ring to check air gap between pulse ring and wheel speed sensor (pulse ring
distortion).
2. Check hydraulic pressure unit HCU
a. Jack up vehicle to confirm that wheel may rotate freely.
b. Release manual brake.
c. After connecting fault diagnosis instrument, turn ignition switch to ON, here it is not necessary to start up
engine.
e. Check with reference to hydraulic control unit diagnosis.
Note: when connect or remove fault diagnosis instrument, ignition switch must be in OFF position