door GENESIS G80 2023 Owners Manual

9-22
Maintenance
Battery Capacity Label
ORG3EV091053L
ÃThe actual battery label in the vehicle
may differ from the illustration.
1. AGM60L-DIN : The Genesis model
name of battery
2. 60Ah(20HR) : The nominal capacity
(in Ampere hours)
3. 100RC : The nominal reserve capacity
(in min.)
4. 12V : The nominal voltage
5. 640CCA / 512A : The cold-test current
in amperes by SAE/EN
Battery Recharging
By battery charger
Should your vehicle’s battery become
discharged either run the motor for at
least 60 minutes driving. Alternatively
you may connect a fully automatic
regulated charger to the motor
compartment front jumper posts or at
the battery in the trunk.
WARNING
Always follow these instructions when
recharging your vehicle’s battery to
avoid the risk of SERIOUS INJURY or
DEATH from explosions or acid burns:

[Before performing maintenance or
recharging the battery, turn off all
accessories and stop the vehicle.

[Keep all flames, sparks, or smoking
materials away from the battery.

[Always work outdoors or in an area
with plenty of ventilation.

[Wear eye protection when checking
the battery during charging.

[The battery must be removed from
the vehicle and placed in a well
ventilated area.

[Watch the battery during charging,
and stop or reduce the charging
rate if the battery cells begin boiling
violently.

[The negative battery cable must
be removed first and installed last
when the battery is disconnected.
Disconnect the battery charger in the
following order:
1. Turn off the battery charger main
switch.
2. Unhook the negative clamp from
the negative battery terminal.
3. Unhook the positive clamp from
the positive battery terminal.

[Use batteries for replacement from
an authorized retailer of Genesis
Branded products.

9-31
09
WARNING
The traction grade assigned to
this tire is based on straight ahead
braking traction tests, and does not
include acceleration, cornering,
hydroplaning, or peak traction
characteristics.
Temperature - A, B & C
The temperature grades are A (the
highest), B and C representing the
tire’s resistance to the generation
of heat and its ability to dissipate
heat when tested under controlled
conditions on a specified indoor
laboratory test wheel.
Sustained high temperature can
cause the material of the tire to
degenerate and reduce tire life,
and excessive temperature can
lead to sudden tire failure. Grades
B and A represent higher levels of
performance on the laboratory test
wheel than the minimum required
by law.
WARNING
The temperature grade for this
tire is established for a tire that
is properly inflated and not
overloaded. Excessive speed,
under-inflation, over-inflation, or
excessive loading, either separately
or in combination, can cause heat
build-up and possible sudden
tire failure. This may cause loss
of vehicle control resulting in an
accident.
Tire Terminology and Definitions
Air pressure
The amount of air inside the tire
pressing outward on the tire. Air
pressure is expressed in pounds per
square inch (psi) or kilopascal (kPa).
Accessory weight
This means the combined weight
of optional accessories. Some
examples of optional accessories
are automatic transmission, power
seats, and air conditioning.
Aspect ratio
The relationship of a tire’s height to
its width.
Belt
A rubber coated layer of cords that
is located between the plies and the
tread. Cords may be made from steel
or other reinforcing materials.
Bead
The tire bead contains steel wires
wrapped by steel cords that hold the
tire onto the rim.

9-41
09
Instrument panel fuse panel
Fuse NameFuse Rating Circuit Protected
Module 910AOverhead Console, AMP, A/V & Navigation Head Unit,
Driver/Passenger Power Seat Module, Inverter (Rear),
Rear Seat LH/RH Heater Unit, Electro Chromic Mirror,
Rear Seat Console Remote Control Switch, SDC,
Smart Phone Wireless Charger, Data Link Connector
Module 1110AHead Lamp LH/RH, ADAS Unit (Parking),
Multifunction Switch
Module1210A IAU, IBU
A/C310AA/C Control Module, Front A/C Controller,
Rear A/C Controller
A/BAG IND.10A Instrument Cluster, Overhead Console
E-Shifter210A Electronic ATM Shift Dial
Spare15A Not Used
Module 1010A ICU Junction Block (ESU)
Module 710ADriver Door Module, Stop Lamp Switch, IBU, IAU,
Multifunction Switch
Multi Media25A A/V & Navigation Head Unit
Module 1310AICU Junction Block (ESU), A/C Control Module,
Front A/C Controller, Rear A/C Controller,
Instrument Cluster, Head-Up Display, Security Indicator
Cluster10A Instrument Cluster, Head-Up Display
IBU 210A IBU
Airbag 215ASRS Control Module, Passenger Occupant Detection
Sensor
Presafety Seat
Belt 310A Pre-Active Seat Belt Unit
Module810ARear Corner Radar LH/RH, ECS Unit, Crash Pad Switch,
ADAS Unit (Driving), ADAS Unit (Parking), Front View
Camera, Front Console Switch, Steering Tilt & Telescopic
Unit
Spare10A Not Used
Module310ARear Corner Radar LH/RH, Front Console Keyboard,
Rear Seat Console Remote Control Switch, VESS Unit,
Steering Tilt & Telescopic Unit, Front Corner Radar LH/RH,
Smart Phone Wireless Charger, Clock Spring

9-42
Maintenance
Instrument panel fuse panel
Fuse NameFuse Rating Circuit Protected
P/Window LH30ARear Power Window Module LH, Driver Power Window
Module
Curtain10A IBU
P/Seat PASS 225A Passenger Power Seat Module
Trunk Open10A Trunk Latch Motor
Airbag 115A SRS Control Module
E-Shifter 110A Electronic ATM Shift Dial, SCU
Module 410ADriver/Passenger Power Outside Mirror, Hazard Switch,
Rear Seat Console Remote Control Switch, Rain Sensor,
Data Link Connector, A/C Control Module,
Rear Occupant Alert (ROA) Sensor, Multifunction Switch,
Passenger Power Seat Module
P/Seat DRV 125A Driver Power Seat Module
P/Seat10A Driver Lumbar Support Unit
Power Handle15A Steering Tilt & Telescopic Unit
Module 515ADriver Door Module, Driver/Passenger Power Seat Switch,
Driver/Passenger Power Seat Module, PTL Unit,
Driver Lumbar Support Unit
IBU 110A BLE Unit, IBU, IAU, Driver/Passenger Door Outside Handle
Power Outlet20A Armrest Power Outlet
P/Seat DRV 225A Driver Power Seat Module
P/Seat PASS 125A Passenger Power Seat Module
S/Heater DRV20A Driver Power Seat Module
S/Heater PASS20A Passenger Power Seat Module
Door Lock20A Center Door Lock/Unlock Relay, Driver Door Unlock Relay
Spare10A Not Used
Module 210ACDM, P/R Junction Block (Blower Relay, Rear Heated
Relay)
Module 610AArmrest Lamp, IBU, A/V & Navigation Head Unit, IAU,
ADAS Unit (Parking), Front Console Keyboard,
Electronic ATM Shift Dial, Front Tray Lamp, VESS Unit,
Rear Seat Console Remote Control Switch, AMP,
Rear Console USB Charger
Brake Switch10A Stop Lamp Switch, IBU

9-47
09
Rear junction block
Fuse Name Fuse Rating Circuit Protected
B+4 50AICU Junction Block (Fuse(P/Seat PASS 2, Module 4,
Door Lock, Trunk Open))
B+2 30AICU Junction Block (Fuse(IBU 1, E-Shifter 1, Spare (B+),
Module 2, Module 5,
Airbag 1), IPS2, IPS5, IPS6)
B+1 50AICU Junction Block (Fuse(Brake Switch), IPS1, IPS3,
IPS4, IPS7,
Long/Short Term Load Latch Relay)
B+3 50AICU Junction Block (Fuse(P/Seat, Curtain, P/Window
LH, S/Heater DRV,
S/Heater PASS, P/Seat DRV 1, P/Seat DRV 2, P/Seat
PASS 1, Power Handle))
Charger 15A Charging Connector Lock/Unlock Relay
P/Window RH 30ARear Power Window Module RH, Passenger Power
Window Module
AMP 25A AMP
P/Door RL 15A Rear Door Latch LH
Solar Charger 2 15A SDC
P/Door PASS 15A Passenger Door Latch
Solar Charger 1 20A SDC
Presafety Seat
Belt 130A Pre-Active Seat Belt Unit
P/Door RR 15A Rear Door Latch RH
ECS 15A ECS Unit
P/Door DRV 15A Driver Door Latch
Presafety Seat
Belt 230A Pre-Active Seat Belt Unit
Child Lock 15A Child Lock/Unlock Relay
Inverter 2 10A Inverter (Rear)
S/Heater Rear LH 20A Rear Seat LH Heater Unit
Power Trunk 30A PTL Unit (Power Trunk Lid)
S/Heater Rear RH 20A Rear Seat RH Heater Unit

9-48
Maintenance
Battery Junction Block
Fuse Name Fuse Rating Circuit Protected
B+8 100ARear Junction Block (Fuse(B+2, B+4, Solar Charger 1,
P/Door Rear LH, P/Door Rear RH, Presafety Seat Belt 2))
B+7 100ARear Junction Block (Fuse(B+3, S/Heater Rear LH, Child
Lock, S/Heater Rear RH, Power Trunk, P/Door DRV, P/Door
PASS))
B+6 100ARear Junction Block (Fuse(B+1, AMP, P/Window RH, ECS,
Presafety Seat Belt 1, Charger))
AMS 10A 12V Battery Sensor

9-54
Maintenance
„Glove box lamp
ORG3EV091034
„Inner door handle lamp (1) / Mood lamp (2) / Door foot lamp (3)
ORG3EV051063
(1) Inner door handle lamp
(2) Mood lamp
(3) Door foot lamp
„Trunk lamp
ORG3EV091023
If the LED lamp (1) does not operate,
have the system inspected by an
authorized retailer of Genesis Branded
products.
The LED lamps cannot be replaced as
a single unit because it is an integrated
unit. The LED lamps has to be replaced
with the unit.
A skilled technician should check or
repair the LED lamp, for it may damage
related parts of the vehicle.

9-55
09
Exterior Care
NOTICE
If you park your vehicle near a stainless
steel sign or glass facade building, the
vehicle’s exterior plastic parts such
as a bumper, spoiler, garnish, lamp
or outside rearview mirror might be
damaged due to sunlight reflected from
the sign or building. To prevent damage
of the exterior plastic parts, you should
avoid parking in areas where light may
be reflected or use a car cover. (The
exterior plastic parts applied to your
vehicle may vary.)
Exterior general caution
It is very important to follow the label
directions when using any chemical
cleaner or polish. Read all warning and
caution statements that appear on the
label.
Finish maintenance
Washing
To help protect your vehicle’s finish from
rust and deterioration, wash it thoroughly
and frequently at least once a month
with lukewarm or cold water.
If you use your vehicle for off-road
driving, you should wash it after each
off-road trip. Pay special attention to the
removal of any accumulation of salt, dirt,
mud, and other foreign materials. Make
sure the drain holes in the lower edges
of the doors and rocker panels are kept
clear and clean.Insects, tar, tree sap, bird droppings,
industrial pollution and similar deposits
can damage your vehicle’s finish if not
removed immediately.
Even prompt washing with plain water
may not completely remove all these
deposits. A mild soap, safe for use on
painted surfaces, should be used.
After washing, rinse the vehicle
thoroughly with lukewarm or cold water.
Do not allow soap to dry on the finish.
High-pressure washing

[When using high-pressure washers,
make sure to maintain sufficient
distance from the vehicle.
Insufficient clearance or excessive
pressure can lead to component
damage or water penetration.

[Do not spray the camera, sensors or
its surrounding area directly with a
high pressure washer. Shock applied
from high pressure water may cause
the device to not operate normally.

[Do not bring the nozzle tip close to
boots (rubber or plastic covers) or
connectors as they may be damaged
if they come into contact with high
pressure water.
WARNING
After washing the vehicle, test the
brakes while driving slowly to see
if they have been affected by water
before getting on the road. If braking
performance is impaired, dry the
brakes by applying them lightly while
maintaining a slow forward speed.
APPEARANCE CARE

9-58
Maintenance
Underbody maintenance
Corrosive materials used for ice and
snow removal and dust control may
collect on the underbody. If these
materials are not removed, accelerated
rusting can occur on underbody parts
such as the frame and floor pan, even
though they have been treated with rust
protection.
Thoroughly flush the vehicle underbody
and wheel openings with lukewarm or
cold water once a month, after off-road
driving and at the end of each winter. Pay
special attention to these areas because
it is difficult to see all the mud and dirt.
It will do more harm than good to wet
down the road grime without removing
it. The lower edges of doors, rocker
panels, and frame members have drain
holes that should not be allowed to clog
with dirt; trapped water in these areas
can cause rusting.
WARNING
After washing the vehicle, test the
brakes while driving slowly to see if
they have been affected by water. If
braking performance is impaired, dry
the brakes by applying them lightly
while maintaining a slow forward
speed.
Aluminum wheel maintenance
The aluminum wheels are coated with a
clear protective finish.

[Do not use abrasive cleaner, polishing
compound, solvent, or wire brushes
on aluminum wheels.

[Clean the wheel when it has cooled.

[Use only a mild soap or neutral
detergent, and rinse thoroughly with
water. Also, clean the wheels after
driving on salted roads.

[Do not wash the wheels with high-
speed car wash brushes.

[Do not use any cleaners containing
acid or alkaline detergents.
Corrosion protection
Protecting your vehicle from corrosion
By using the most advanced design
and construction practices to combat
corrosion, Genesis Branded Vehicle
produces vehicles of the highest quality.
However, this is only part of the job.
To achieve the long-term corrosion
resistance your vehicle can deliver, the
owner’s cooperation and assistance is
also required.
Common causes of corrosion
The most common causes of corrosion
on your vehicle are:

[Road salt, dirt and moisture that is
allowed to accumulate underneath
the vehicle.

[Removal of paint or protective
coatings by stones, gravel, abrasion
or minor scrapes and dents which
leave unprotected metal exposed to
corrosion.

9-59
09
High-corrosion areas
If you live in an area where your vehicle is
regularly exposed to corrosive materials,
corrosion protection is particularly
important. Some of the common causes
of accelerated corrosion are road salts,
dust control chemicals, ocean air and
industrial pollution.
Moisture breeds corrosion
Moisture creates the conditions in
which corrosion is most likely to occur.
For example, corrosion is accelerated
by high humidity, particularly when
temperatures are just above freezing. In
such conditions, the corrosive material is
kept in contact with the vehicle surfaces
by moisture that is slow to evaporate.
Mud is particularly corrosive because
it is slow to dry and holds moisture in
contact with the vehicle. Although the
mud appears to be dry, it can still retain
moisture and promote corrosion.
High temperatures can also accelerate
corrosion of parts that are not properly
ventilated so the moisture can be
dispersed. For all these reasons, it is
particularly important to keep your
vehicle clean and free of mud or
accumulations of other materials. This
applies not only to the visible surfaces
but particularly to the underside of the
vehicle.
To help prevent corrosion
Keep your vehicle clean
The best way to prevent corrosion is
to keep your vehicle clean and free of
corrosive materials. Attention to the
underside of the vehicle is particularly
important.

[If you live in a high-corrosion area —
where road salts are used, near the
ocean, areas with industrial pollution,
acid rain, etc.—, you should take extra
care to prevent corrosion. In winter,
hose off the underside of your vehicle
at least once a month and be sure to
clean the underside thoroughly when
winter is over.

[When cleaning underneath the
vehicle, pay particular attention to the
components under the fenders and
other areas that are hidden from view.
Do a thorough job; just dampening
the accumulated mud rather than
washing it away will accelerate
corrosion rather than prevent it. Water
under high pressure and steam are
particularly effective in removing
accumulated mud and corrosive
materials.

[When cleaning lower door panels,
rocker panels and frame members, be
sure that drain holes are kept open so
that moisture can escape and not be
trapped inside to accelerate corrosion.