check GENESIS G90 2023 Owner's Manual
[x] Cancel search | Manufacturer: GENESIS, Model Year: 2023, Model line: G90, Model: GENESIS G90 2023Pages: 676, PDF Size: 14.16 MB
Page 179 of 676
5-38
Convenience Features
Operating Door Locks from
Inside the Vehicle
Using the door open button
ORS051021
Press the door open button from inside
the vehicle to open the door.
[ Always close and lock the doors when
the vehicle is moving. Locking the
doors prevent others from entering
the vehicle while the vehicle is
stopped or moving slowly.
[ If the smart key is in the vehicle
and either front door is opened, the
doors will not lock even though the
door lock button on the smart key or
central door lock switch is pressed.
NOTICE
[ Do not open the door excessively
multiple times using the door open
button. It may engage the protection
circuit and temporarily disable the
button.
[ If equipped with the Easy Close
feature, the door will open about 7.9
in. (20 cm). Check for any obstacles
before opening the door.
WARNING
Only open the door with the door open
button when the vehicle has completely
stopped.
The door may open while the vehicle is
in motion if you press the button.
Opening the door manually
ORS051026
If the door does not open with the door
open button due to battery discharge or
vehicle breakdown, pull the emergency
open lever under the door pocket twice
to open the door. You may use the
emergency open lever even if there is no
problem with the door open button.
CAUTION
Do not apply excessive force on the
door, door handle and emergency open
lever to avoid damage.
Information
The door will open in the following
conditions by pulling the emergency open
lever only once.
[ When the door emergency open lever is
already used once (for all doors)
[ When the battery is low. (for driver
side door)
[ When the mechanical key on the
driver’s door is used
Page 190 of 676
5-49
05
WARNING
Even if your vehicle is equipped with
Rear Occupant Alert, always make sure
to check the rear seat before you leave
the vehicle.
Advanced Rear Occupant Alert may not
operate when:
[ Movement does not continue for
a certain period of time or the
movement is small.
[ A child is not seated in a child
restraint system.
[ The detection signal is weak because
the signal is obscured by seat or CRS
(for example, child is restrained in
the forward-facing CRS).
[ Movement is detected in areas other
than the rear seats.
[ The rear passenger is covered with a
fabric containing metallic substance
such as a blanket.
[ An object in the vehicle blocks the
sensor.
[ The sensor is contaminated by
foreign material.
[ An animal at the rear seat is not large
enough to be detected by the sensor
or there is hardly any movement.
[ Attaching objects or modifying the
interior ceiling, or the interior ceiling
is deformed or damaged.
[ There are electronic interference
around the vehicle.
[ Other environmental reasons that
may affect the system.
Declaration of Conformity
The radio frequency components (ROA
Radar Sensor) complies:
- For USA
OANATEL323
- For Canada
OANATEL324
Page 195 of 676
5-54
Convenience Features
The Smart Posture Care system
automatically provides a healthy posture
(position) for the driver’s back, and sets
the steering wheel, side view mirrors,
head-up display positions according to
the driver’s body measurements.
Information
, I W K H 6 H D W 3 R V W X U H & D U H V \ V W H P G R H V Q R W
operate normally, have the system checked
by an authorized retailer of Genesis
Branded products.
OJWEV051211N
1. Check that the gear is in P (Park) while
the Engine Start/Stop button is in the
ON position.
2. 6 H O H F W S 6 H W X S
Page 196 of 676
5-55
05
Motor Driven Power Steering
(MDPS)
The system assists you with steering the
vehicle. If the vehicle is turned off or
if the power steering system becomes
inoperative, you may still steer the
vehicle, but it will require increased
steering effort.
Should you notice any change in the
effort required to steer during normal
vehicle operation, have the system
checked by an authorized retailer of
Genesis Branded products.
CAUTION
If Motor Driven Power Steering does not
operate normally, the warning light
and the message ‘Check motor driven
power steering’ will illuminate on the
instrument cluster. You may steer the
vehicle, but it will require increased
steering efforts. Take the vehicle to an
authorized retailer of Genesis Branded
products and have the system checked
as soon as possible.
Information
The following symptoms may occur during
normal vehicle operation:
[ The steering effort may be high
immediately after pressing the Engine
6 W D U W 6 W R S E X W W R Q W R W K H 2 1 S R V L W L R Q
This happens as the system performs
the MDPS system diagnostics. When
the diagnostics are completed, the
steering wheel effort will return to its
normal condition.
[ When the battery voltage is low, you
might have to put more steering effort.
However, it is a temporary condition so
that it will return to normal condition
after charging the battery.
[ A click noise may be heard from the
MDPS relay after the Engine Start/Stop
E X W W R Q L V L Q W K H 2 1 R U 2 ) ) S R V L W L R Q
[ Motor noise may be heard when the
vehicle is at a stop or at a low driving
speed.
[ When you operate the steering wheel
in low temperatures, abnormal noise
may occur. If the temperature rises, the
noise will disappear. This is a normal
condition.
[ When an error is detected from MDPS,
the steering effort assist function will
not be activated in order to prevent
fatal accidents. Instrument cluster
warning lights may be on or the
steering effort may be high. If these
symptoms occur, drive the vehicle to
a safe area as soon as it is safe to do
so. Have the system checked by an
authorized retailer of Genesis Branded
products as soon as possible.
STEERING WHEEL
Page 201 of 676
5-60
Convenience Features
NOTICE
When using snow chains, be sure to
turn off the Rear Wheel Steering by
selecting ‘Snow Chains Installed’ from
the Settings menu in the infotainment
system to protect the vehicle.
After removing the snow chain,
deselect ‘Snow Chains Installed’ from
the Settings menu in the infotainment
system. If it is not deselected, Rear
: K H H O 6 W H H U L Q J Z L O O Q R W R S H U D W H ) R U
more details on setting the menu, refer
to “Winter Tire” section in Chapter 6.
CAUTION
[ If there is a problem with the Rear
Wheel Steering system, a warning
light and warning message appears
on the instrument cluster and
Rear Wheel Steering system stops
working. If the warning light and
warning message are still displayed
even when the vehicle is stopped
and the engine is restarted, have the
vehicle checked by an authorized
retailer of Genesis Branded products.
[ If the Rear Wheel Steering system
operation is stopped while the rear
wheels are not straight, the vehicle
may lean to one side while driving.
Information
With no warning light on the instrument
cluster, the following conditions are
normal:
[ Immediately after starting the engine,
Rear Wheel Steering system performs
diagnostics and operates normally after
about 2 seconds.
[ When turning the engine on or off,
Rear Wheel Steering system can
operate for about 2 seconds even
though the steering wheel is not steered
to check system condition.
[ Motor noise may be heard when you
steer the vehicle while stopping or
driving at low speed.
[ In driving conditions in which the rear
wheels are steered in the same direction
as the front wheels when (
) is on
the instrument cluster by pressing the
Lane Following Assist button on the
steering wheel or Highway Driving
Assist function is activated, keep the
rear wheels straight to improve Lane
Keeping Assist performance.
[ , I
Page 202 of 676
5-61
05
MIRRORS
Inside Rearview Mirror
Before driving your vehicle, check to
see that your inside rearview mirror is
properly positioned. Adjust the rearview
mirror so that the view through the rear
window is properly centered.
WARNING
Make sure your line of sight is not
obstructed. Do not place objects in the
rear seat, cargo area, or behind the rear
headrests which could interfere with
your vision through the rear window.
WARNING
To prevent serious injury during an
accident or deployment of the air bag,
do not modify the rearview mirror and
do not install a wide mirror.
WARNING
NEVER adjust the mirror while driving.
This may cause loss of vehicle control
resulting in an accident.
NOTICE
When cleaning the mirror, use a paper
towel or similar material dampened
with glass cleaner. Do not spray glass
cleaner directly on the mirror as this
may cause the liquid cleaner to enter
the mirror housing.
Electrochromic mirror (ECM) with
HomeLink® system
Your vehicle may be equipped with
a Gentex Automatic-Dimming Mirror
with an Integrated HomeLink® Wireless
Control System.
During nighttime driving, this feature
will automatically detect and reduce
rearview mirror glare. The HomeLink®
Universal Transceiver allows you to
activate your garage door(s), electric
gate, home lighting, etc.
ORS052039N
M HomeLink Channel 1
N HomeLink Channel 2
O HomeLink Channel 3
P Garage Door Opener Status Indicator:
Closing or Closed
Q HomeLink Operation Indicator
R Garage Door Opener Status Indicator:
Opening or Opened
S HomeLink User Interface Indicator
Page 206 of 676
5-65
05
3) Two-Way Communication
3 U R J U D P P L Q J ) R U V H O H F W J D U D J H G R R U
openers)
If your garage door opener has the
‘myQ’ logo on its side, your opener
likely has Two-Way Communication
capability. HomeLink has the capability
to establish Two-Way Communication
with your garage door opener. HomeLink
can receive and display “closing”
or “opening” status messages from
compatible garage door openers. At
any time, Home-Link can also recall
and display the last recorded status
communicated by the garage door
opener to indicate your garage door
being “closed” or “opened”.
To check if your garage door opener is
compatible with this feature, refer to
www.homelink.com/compatible/Two-
way-Communication. If your garage
door opener has this functionality, AND
the Two-Way Communication indicators
P, R in the mirror appear while the
garage door is opening/closing, then
no further steps are needed. Two-Way
Communication Programming is already
complete. However, if your garage door
opener has this functionality, AND the
Two-Way Communication indicators P,
R in the mirror DO NOT appear while
the garage door is opening/closing, use
the following instructions to enable this
functionality.
1. In your vehicle, press and hold the
programmed HomeLink button for 2
seconds, then release. Confirm that
the garage door is moving. AFTER it
stops, you will have one minute to
complete the following steps:
ÃA ladder and/or second person may
simplify the following steps.2. On your garage door opener in your
garage, locate the “Learn” button
(usually near where the hanging
antenna wire is attached to the garage
door opener). If there is difficulty
locating this button, reference the
device’s owner’s manual.
3. Press and release the “Learn” button.
4. A light on your garage door opener
may flash, and your Two-Way
Communication indicators P, R in
your vehicle may flash, confirming
completion of the process.
5. Return to the vehicle and firmly
press and release the programmed
HomeLink button to activate
your garage door. The Two-Way
Communication indicators P, R flash
in orange when the door is moving.
Do not make any additional button
presses until AFTER the garage door
has come to a complete stop.
6. Your Two-Way Communication
programming is now complete.
Information
If your garage door opener has Two-
: D \ & R P P X Q L F D W L R Q I X Q F W L R Q D O L W \
it is possible for HomeLink to stop
functioning the garage door shortly
after initial programming, IF the Two-
: D \ & R P P X Q L F D W L R Q 3 U R J U D P P L Q J
wasn’t properly completed. This
usually happens after the first 10 times
a programmed HomeLink button is
pressed. If you experience this, completing
the “Programming a New HomeLink
% X W W R Q
Page 227 of 676
5-86
Convenience Features
Opening the Hood
ORS051056
1. Park the vehicle and set the parking
brake.
2. Pull the release lever to unlatch the
hood. The hood should pop open
slightly.
ORS051057
3. Go to the front of the vehicle, raise the
hood slightly, push up the secondary
latch M inside of the hood center and
lift the hood N.
After the hood has been lifted halfway,
it will raise completely by itself.
Closing the Hood
1. Before closing the hood, check in and
around the engine compartment to
ensure the following:
- Any tools or other loose objects
are removed from the engine
compartment area or hood
opening area
- All glove, rags, or other
combustible material is removed
from the engine compartment
- All filler caps are tightly and
correctly installed
2. Lower the hood halfway (lifted
approximately 12 in. (30 cm) from the
closed position) and push down to
securely lock in place. Then double
check to be sure the hood is secure.
If the hood can be raised slightly, it is
not securely locked. Open it again and
close it with more force.
WARNING
[ Before closing the hood, ensure
all obstructions are removed from
around the hood opening.
[ Always double check to be sure that
the hood is firmly latched before
driving away. Check there is no
hood open warning light or message
displayed on the instrument cluster.
Driving with the hood opened may
cause a total loss of visibility, which
might result in an accident.
[ Do not move the vehicle with the
hood in the raised position, as vision
is obstructed, which might result in
an accident, and the hood could fall
or be damaged.
HOOD
Page 238 of 676
5-97
05
WARNING
Automotive fuel is highly flammable
D Q G H [ S O R V L Y H ) D L O X U H W R I R O O R Z W K H V H
guidelines may result in SERIOUS
INJURY or DEATH:
[ Read and follow all warnings posted
at the gas station.
[ Before refueling, note the location
R I W K H ( P H U J H Q F \ ) X H O 6 K X W 2 I I L I
available, at the gas station.
[ Before touching the fuel nozzle, you
should eliminate the potential build-
up of static electricity by touching
a metal part of the vehicle, a safe
distance away from the fuel filler
neck, nozzle, or other gas source,
with your bare hand.
[ Do not use mobile phones while
refueling. Electric current and/or
electronic interference from cellular
phones can potentially ignite fuel
vapors and cause a fire.
[ Do not get back into a vehicle
once you have begun refueling.
You can generate a buildup of
static electricity by touching,
rubbing or sliding against any item
or fabric capable of producing
static electricity. Static electricity
discharge can ignite fuel vapors
causing a fire. If you must re-enter
the vehicle, you should once again
eliminate potentially dangerous
static electricity discharge by
touching a metal part of the vehicle,
away from the fuel filler neck, nozzle
or other fuel source, with your bare
hand.[ When using an approved portable
fuel container, be sure to place the
container on the ground prior to
refueling. Static electricity discharge
from the container can ignite fuel
vapors causing a fire.
Once refueling has begun, contact
between your bare hand and the
vehicle should be maintained until
the filling is complete.
[ Use only approved portable plastic
fuel containers designed to carry and
store fuel.
[ When refueling, always shift the
gear to the P (Park) position, set
the parking brake, and press the
Engine Start/Stop button to the
2 ) ) S R V L W L R Q 6 S D U N V S U R G X F H G E \
electrical components related to the
engine can ignite fuel vapors causing
a fire.
[ Do not use matches or a lighter and
do not smoke or leave a lit cigarette
in your vehicle while at a gas station,
especially during refueling.
[ Do not over-fill or top-off your
vehicle tank, which can cause fuel
spillage.
[ If a fire breaks out during refueling,
leave the vicinity of the vehicle, and
immediately contact the manager
of the gas station and then contact
W K H O R F D O I L U H G H S D U W P H Q W ) R O O R Z D Q \
safety instructions they provide.
[ If pressurized fuel sprays out, it can
cover your clothes or skin and thus
subject you to the risk of fire and
burns. Always remove the fuel cap
carefully and slowly. If the cap is
venting fuel or if you hear a hissing
sound, wait until the condition stops
before completely removing the cap.
[ Always check that the fuel cap is
installed securely to prevent fuel
spillage in the event of an accident.
Page 243 of 676
5-102
Convenience Features
Updating Software
ORS052314N
You can see the progress of the update
on the screen.
After the update is complete, you will
receive a notification on your phone
or the vehicle screen that the software
update is complete.
Information
The screen turns off automatically after 3
minutes to save the battery. If the screen
turns off automatically, you can check the
update progress by pressing the Engine
Start/Stop button.
Information
[ After the update starts, you can exit the
vehicle.
[ 7 K H 2 Y H U 7 K H $ L U V R I W Z D U H X S G D W H
feature is only available for Active and
( Q U R O O H G * H Q H V L V & R Q Q H F W H G 6 H U Y L F H V
users.
[ The update details may vary, for details
you can visit the What’s New link.
[ & K H F N W K H Q R W L F H I R U W K H 2 Y H U 7 K H $ L U
software update on mygenesis.com
[ , I W K H X S G D W H I D L O V W K H ( & 8 Z L O O
attempt to recovery itself automatically
(rollback). If you want to retry the
software update, even after a successful
U H F R Y H U \ F R Q W D F W * H Q H V L V & X V W R P H U
& D U H
[ If the update or recovery fails, contact
* H Q H V L V & X V W R P H U & D U H
[ After the update is complete, it
may provide new functions or
improvements. For more information,
V H H W K H