Steering wheel buttons GENESIS G90 2023 Owners Manual

5-51
05
Storing Memory Positions
1. Shift to P (Park) while the Engine
Start/Stop button is in the ON
position.
2. Adjust the seat position, side view
mirror position, steering wheel
position and head-up display height/
brightness to the desired position.
3. Press and hold one of the memory
buttons (1, 2 or 3). The system will
beep twice when the memory has
been successfully stored.
‘Settings 1 (2 or 3) saved’ will appear
on the cluster LCD display.
Recalling Memory Positions
1. Shift to P (Park) while the Engine
Start/Stop button is in the ON
position.
2. Press the desired memory button (1,
2 or 3). The system will beep once,
and then the seat position, side
view mirror position, steering wheel
position and head-up display height/
brightness will automatically adjust to
the stored positions.
‘Settings 1 (2 or 3) applied’ will appear
on the cluster LCD display.
If you press the corresponding button
which the setting is being recalled, the
setting will temporarily deactivate. If you
press the other buttons, the setting of
the pressed button will activate.
For example, if you press number 1
button with the number 1 setting in
operation, the setting will temporarily
deactivate. If you press the number
2 button, the number 2 setting will
activate.
If you adjust the seat, side view mirror,
steering wheel or head-up display while
recalling the stored positions, the pre-set
settings will become ineffective.
Information

[Up to 3 memories for front seats and
up to 2 memories for rear seats can be
saved.

[2QO\WKHGULYHU

5-167
05
Antenna
ORS051212
The shark fin antenna will receive AM,
FM broadcast signals and transmit data.
Steering Wheel Remote Controls
ORS051213
NOTICE
Do not operate multiple audio remote
control buttons simultaneously.
(1) Volume (+/-)

[Push the Volume scroll up to increase
volume.

[Push the Volume scroll down to
decrease volume.
Mute ()

[Press the Mute button to mute the
sound.

[Press the Mute button again to
activate the sound.

7-157
07
7KHIXQFWLRQZLOOSDXVHLQWKHIROORZLQJ
conditions when:

[There is a pedestrian, animal or object
in the direction the vehicle is moving

[The door or trunk is open

[The Forward (
) or Backward ()
button is not continuously pressed

[Simultaneously pressing multiple
buttons on a smart key

[The smart key is not operated within
13 ft. (4 m) from the vehicle

[Button of another smart key is pressed
in addition to the operating smart key

[Blind-Spot Collision-Avoidance
Assist or Rear Cross-Traffic Collision-
Avoidance Assist operates while the
vehicle is being controlled in the
reverse direction.

[The vehicle moves 22 ft. (7 m) while
the smart key is pressed with Remote
Operation function (maximum travel
distance per button press)
When Remote operation function is
paused, the vehicle will stop. If the
condition that made the function to
pause disappears, the function may
operate again.
The function will cancel in the following
conditions when:

[The steering wheel is steered

[The gear is shifted while the vehicle is
moving

[Operating EPB while the vehicle is
moving

[The hood is open

[The brake pedal or accelerator pedal
is depressed when all the doors are
closed

[The smart key is outside the vehicle
when the brake pedal is depressed
while the driver's door is open

[Rapid acceleration occurs

[Vehicle skid occurs

[The wheel is stuck by an obstacle and
cannot move

[Approximately 3 minutes and 50
seconds have past after Remote
Operation function has started to
operate

[The slope of the road exceeds the
operational range

[The function is paused for more than
1 minute

[The total travel distance of the vehicle
has exceeded 45 ft. (14 m) after
Remote Operation function operation

[The steering wheel, gearshift, braking,
and drive controls are not working
properly

[There is a problem with the smart key
or the smart key battery is low

[ABS, TCS or ESC system operates due
to slippery road conditions

[The alarm of the Theft Alarm System
sounds
When Remote Operation function is
canceled, the vehicle will automatically
stop, shift the gear to P (Park) and
engage EPB (Electronic Parking Brake).
The engine will turn off.