Vin GENESIS GV60 2023 Owners Manual
[x] Cancel search | Manufacturer: GENESIS, Model Year: 2023, Model line: GV60, Model: GENESIS GV60 2023Pages: 690, PDF Size: 14.07 MB
Page 581 of 690
7-167
07
Remote Operation
Operating order
Remote Operation function operates in
the following order:
1. Getting ready to remotely move
forward and backward
2. Remotely moving forward and
backward
* H W W L Q J U H D G \ W R U H P R W H O \ P R Y H I R U Z D U G
D Q G E D F N Z D U G
There are two ways to operate Remote
Operation function.
OJWEV071155
Method (1) Using the function with
vehicle off
(1) Within a certain range from the
vehicle press the door lock (
)
button on the smart key and lock
all doors.
(2) Press and hold the Remote Start
button (
) within 4 seconds until
the vehicle starts.
[ For more details on remotely
starting the vehicle, refer to
“Remote Start” section in chapter 6.
OJWEV071156N
OJWEV071277L
Method (2) Using the function with
vehicle on
(1) Park the vehicle in front of the
space where you want to use
Remote Operation function, and
shift the gear to P (Park).
(2) Press and hold the Parking/View
(
) button to turn on Smart
Parking Assist. A message ‘Remote
Parking Instructions’ will appear
on the infotainment system
screen.
(3) Get out of the vehicle with the
smart key and close all doors.
Page 583 of 690
7-169
07
Information
[ Check that all smart keys are outside
the vehicle when using Remote
Operation function.
[ Remote Operation function will operate
only when the smart key is within
13 ft. (4 m) from the vehicle. If there
is no vehicle movement even when
the Forward or Backward button is
pressed on the smart key, check the
distance to the vehicle and press the
button again.
[ The detecting range of the smart
key may vary depending on the
surroundings that are affected by radio
waves such as transmission tower,
broadcast station, etc.
[ When remotely moving forward using
method (1), it is recognized as an exit
situation, and the vehicle moves 13
ft. (4 m) to check for parking lines,
pedestrians, animals or objects around
the vehicle. After confirmation, the
steering wheel is controlled according
to the condition ahead.
[ When remotely moving forward
using method (2), it is recognized as a
parking situation, and will immediately
control the steering wheel according
to the condition ahead to assist with
entering the parking space and aligning
the vehicle. However, performance may
reduce depending on the parking lines
pedestrians, animals, shape of objects,
location, etc., around the vehicle.
[ For moving remotely backward, both
method (1) and (2) aligns the steering
wheel first, and then will only move the
vehicle straight.
[ When remotely moving forward or
backward is completed, the vehicle
will automatically shift to P (Park)
and engage EPB (Electronic Parking
Brake).
CAUTION
[ When using Remote Operation
I X Q F W L R Q P D N H V X U H W K D W D O O
S D V V H Q J H U V K D Y H J R W W H Q R X W R I W K H
Y H K L F O H
[ , I W K H Y H K L F O HT V E D W W H U \ L V G L V F K D U J H G
or Remote Smart Parking Assist
malfunctions when parked in a
Q D U U R Z S D U N L Q J V S D F H 5 H P R W H
2 S H U D W L R Q I X Q F W L R Q Z L O O Q R W R S H U D W H
$ O Z D \ V S D U N \ R X U Y H K L F O H L Q D V S D F H
Z L G H H Q R X J K I R U \ R X W R J H W L Q R U R X W
R I \ R X U Y H K L F O H
[ Please note that depending on the
S D U N L Q J V S D F H \ R X P D \ Q R W E H D E O H
W R H [ L W I U R P W K H V S D F H \ R X K D Y H
H Q W H U H G E \ X V L Q J 5 H P R W H 2 S H U D W L R Q
I X Q F W L R Q
[ $ I W H U S D U N L Q J W K H V X U U R X Q G L Q J P D \
F K D Q J H G X H W R W K H P R Y H P H Q W R I
V X U U R X Q G L Q J Y H K L F O H V , I W K L V R F F X U V
5 H P R W H 2 S H U D W L R Q I X Q F W L R Q P D \ Q R W
R S H U D W H
[ % H I R U H O H D Y L Q J W K H Y H K L F O H F O R V H
Z L Q G R Z V D Q G V X Q U R R I V D Q G P D N H
V X U H W K H Y H K L F O H L V R I I E H I R U H O R F N L Q J
W K H G R R U V
Page 584 of 690
![GENESIS GV60 2023 Owners Manual 7-170
Driver Assistance System
Remote Operation function operation
status
Operation
status 6 P D U W N H \ / ( + D ] D U G
warning
light
Under
controlGreen LED
continuously
blinks-
Pause](/img/46/58826/w960_58826-583.png "GENESIS GV60 2023 Owners Manual 7-170
Driver Assistance System
Remote Operation function operation
status
Operation
status 6 P D U W N H \ / ( + D ] D U G
warning
light
Under
controlGreen LED
continuously
blinks-
Pause")
7-170
Driver Assistance System
Remote Operation function operation
status
Operation
status 6 P D U W N H \ / ( ' + D ] D U G
warning
light
Under
controlGreen LED
continuously
blinks-
PauseRed LED
continuously
blinksBlinks
OffRed LED
illuminates for
4 seconds and
then turns offBlinks 3
times and
turns off
CompleteGreen LED
illuminates for
4 seconds and
then turns offBlinks 1
time and
turns off
ÃOperation status by the hazard
warning light may not be applicable
based on the regulation of your
country.
ÃIf the smart key is not within the
operating range from the vehicle
(approximately 13 ft. (4 m)), the
smart key LED will not illuminate or
blink. Use the smart key within the
operating range.
How to turn off Remote Operation
function while operating
[ Press the Parking/View () button
while the infotainment system screen
guides the driver using method 2.
[ Shift the gear except to P (Park)
while the infotainment system screen
guides the driver using method 2.
[ Press the Parking Safety (
) button
or select ‘Cancel’ on the infotainment
system screen.
[ Press the Remote Start (
) button
on the smart key while the vehicle is
being controlled by Remote Operation
function. Remote Operation function
will turn off. At this time, the vehicle
will turn off.
[ Get on the vehicle with the smart
key. Remote Operation function will
turn off. At this time, the vehicle will
remain on.
The function will pause in the following
conditions when:
[ There is a detected pedestrian, animal
or object in the direction the vehicle
is moving
[ The door or liftgate is open
[ The Forward (
) or Backward ()
button is not continuously pressed
[ Simultaneously pressing multiple
buttons on a smart key
[ The smart key is not operated within
13 ft. (4 m) from the vehicle
[ Button of another smart key is pressed
in addition to the operating smart key
[ Blind-Spot Collision-Avoidance
Assist or Rear Cross-Traffic Collision-
Avoidance Assist operates while the
vehicle is being controlled in the
reverse direction.
Page 585 of 690
7-171
07
[ The vehicle moves 22 ft. (7 m) while
the smart key is pressed with Remote
Operation function (maximum travel
distance per button press)
When Remote Operation function is
paused, the vehicle will stop. If the
condition that made the function to
pause disappears, the function may
operate again.
The function will cancel in the following
conditions when:
[ The steering wheel is steered
[ The gear is shifted while the vehicle is
moving
[ Operating EPB while the vehicle is
moving
[ The hood is open
[ The brake pedal or accelerator pedal
is depressed when all the doors are
closed
[ The smart key is outside the vehicle
when the brake pedal is depressed
while the driver's door is open
[ Rapid acceleration occurs
[ Vehicle skid occurs
[ The wheel is stuck by an obstacle and
cannot move[ Approximately 3 minutes and 50
seconds have past after Remote
Operation function has started to
operate
[ The slope of the road exceeds the
operational range
[ The function is paused for more than
1 minute
[ The total travel distance of the vehicle
has exceeded 45 ft. (14 m) after
Remote Operation function operation
[ The steering wheel, gearshift, braking,
and drive controls are not working
properly
[ There is a problem with the smart key
or the smart key battery is low
[ ABS, TCS or ESC system operates due
to slippery road conditions
[ The alarm of the Theft Alarm System
sounds
[ The charging door is open
When Remote Operation function is
cancelled, the vehicle will automatically
stop, shift the gear to P (Park) and
engage EPB (Electronic Parking Brake).
Page 593 of 690
7-179
07
The function will pause in the
following conditions when:
[ Smart Parking
- There is a pedestrian, animal or
object in the direction the vehicle is
moving
- The door or liftgate is open
- The driver’s seat belt is not fastened
- Blind-Spot Collision-Avoidance
Assist or Rear-Cross Traffic Collision
Assist operates while the vehicle
is being controlled in the reverse
direction
- The Parking/View (
) button is
not continuously pressed
- The vehicle is stopped by
depressing the brake pedal
[ Remote Smart Parking
- There is a pedestrian, animal or
object in the direction the vehicle is
moving
- The door or liftgate is open
- The Forward (
) or Backward ()
button is not continuously pressed
- Simultaneously pressing multiple
buttons on a smart key
- The smart key is not operated within
13 ft. (4 m) from the vehicle
- Button of another smart key is
pressed in addition to the operating
smart key
- Blind-Spot Collision-Avoidance
Assist or Rear-Cross Traffic Collision
Assist operates while the vehicle
is being controlled in the reverse
direction
When Parking function is paused, the
vehicle will automatically stop. If the
condition that made the function to
pause disappears, the function may
operate again.
The function will cancel in the
following conditions when:
[ Smart Parking
- The steering wheel is steered
- The gear is shifted while the vehicle
is moving
- Operating EPB while the vehicle is
moving
- The hood is open
- The driver opens the door with the
seatbelt unfastened
- Rapid acceleration occurs
- Vehicle skid occurs
- The wheel is stuck by an obstacle
and cannot move
- There are pedestrians, animals or
objects at the front and rear of the
vehicle at the same time
- Approximately 3 minutes and 50
seconds have past after Smart
Parking function has started to
operate
- The slope of the road exceeds the
operational range
- The function is paused for more
than 1 minute
- The steering wheel, gearshift,
braking, and drive controls are not
working properly
- ABS, TCS or ESC system operates
due to slippery road conditions
- The charging door is open
When Smart Parking function is
cancelled, the vehicle will automatically
stop, shift the gear to P (Park) and
engage EPB (Electronic Parking Brake).
Page 594 of 690
7-180
Driver Assistance System
[ Remote Smart Parking
- The steering wheel is steered
- The gear is shifted
- Operating EPB while the vehicle is
moving
- The hood is open
- The brake pedal or accelerator
pedal is depressed when all the
doors are closed
- The smart key is outside the vehicle
when the brake pedal is depressed
while the driver's door is open.
- Rapid acceleration occurs
- Vehicle skid occurs
- The wheel is stuck by an obstacle
and cannot move
- There are detected pedestrians,
animals or objects at the front and
rear of the vehicle at the same time
- Approximately 3 minutes and 50
seconds have past after Remote
Smart Parking function has started
to operate
- The slope of the road exceeds the
operational range
- The function is paused for more
than 1 minute
- The steering wheel, gearshift,
braking, and drive controls are not
working properly
- There is a problem with the smart
key or the smart key battery is low
- ABS, TCS or ESC system operates
due to slippery road conditions
- The alarm of the Theft Alarm System
sounds
- The charging door is open
When Remote Smart Parking function is
cancelled, the vehicle will automatically
stop, shift the gear to P (Park) and
engage EPB (Electronic Parking Brake). Smart Exit
Operating order
Smart Exit function operates in the
following order:
1. Getting ready for exit
2. Checking space
3. Select exit direction
4. Smart Exit
* H W W L Q J U H D G \ I R U H [ L W
OJWEV071102
(1) With the vehicle turned on,
depress the brake pedal and shift
the gear to P (Park) or N (Neutral).
(2) Press and hold the Parking/View
(
) button to turn on Remote
Smart Parking Assist.
[ 'Agree' must be selected on the
infotainment system screen and the
infotainment system has to operate
properly to use Smart Smart Exit
function.
[ Drive below 3 mph (5 km/h) with
the vehicle on and shift the gear to
N (Neutral), Smart Exit function can
be used.
[ If the function is turned on again
after parallel parking is completed
by Remote Smart Parking Assist,
Smart Exit function can be used.
Page 596 of 690
7-182
Driver Assistance System
6 P D U W ( [ L W
OJWEV071285L
(1) Press the Parking/View
() button when the vehicle is
stopped by depressing the brake
pedal. When the brake pedal is
released, Remote Smart Parking
Assist will automatically control
the steering wheel, vehicle speed
and gearshift.
(2) While Smart Exit function is
operating, if you do not hold
down the Parking/View button,
the vehicle will stop and function
control will pause. The function
will start operating again when the
Parking/View button is pressed
and held again.
(3) When the vehicle reaches the
target exit location, a message will
appear on the infotainment system
screen to inform you that exit is
complete.[ Smart Exit function will not operate
if the door is open or the seat belt is
not fastened.
[ Vehicle speed can be adjusted
by depressing the brake pedal
while Smart Exit function is
operating. However, the vehicle
does not accelerate even when the
accelerator pedal is depressed.
[ If exit is completed while
depressing the brake pedal, Smart
Exit function will complete with the
gear in D (Drive).
[ If exit is completed while depressing
the accelerator pedal, you must
take your foot off the accelerator
pedal once for the accelerator pedal
to operate.
[ If there is no vehicle operation such
as depressing the brake pedal or
accelerator pedal within 4 seconds
after exit is complete, the vehicle
will automatically shift to P (Park)
and engage EPB (Electronic Parking
Brake).
[ After Exit function is complete,
always check the surroundings
before driving.
Smart Exit operation status
Operation
statusTurn signal
Under
controlThe turn signal of the exit
direction blinks until the exit
is complete or Smart Exit is
cancelled.
ÃOperation status by the turn signal
may not be applicable based on the
regulation of your country.
Page 597 of 690
7-183
07
How to turn off Smart function while
operating
[ Press the Parking/View () button
in the following stage:
- Checking space
- Select exit direction
[ Shift the gear to R (Reverse) in the
following stage:
- Checking space
- Select exit direction
[ Press the Parking Safety (
) button
or select ‘Cancel’ on the infotainment
system screen to turn off Exit
function.
[ While Smart Exit function is operating,
if the vehicle is stopped by depressing
the brake pedal, and the gear is
shifted, Exiting function will turn off.
At this time, EPB (Electronic Parking
Brake) will not be engaged.
The function will pause in the following
conditions when:
[ There is a detected pedestrian, animal
or object in the direction the vehicle
is moving
[ The door or liftgate is open
[ The driver’s seat belt is not fastened
[ Blind-Spot Collision-Avoidance Assist
or Rear-Cross Traffic Collision Assist
operates while the vehicle is being
controlled in the reverse direction
[ The Parking/View (
) button is not
continuously pressed
[ The vehicle is stopped by depressing
the brake pedal
When Exit function is paused, the vehicle
will stop. If the condition that made
the function to pause disappears, the
function may operate again.
The function will cancel in the following
conditions when:
[ Smart Exit
- The steering wheel is steered
- The gear is shifted while the vehicle
is moving
- Operating EPB while the vehicle is
moving
- The hood is open
- The driver opens the door with the
seatbelt unfastened
- Rapid acceleration occurs
- Vehicle skid occurs
- The wheel is stuck by an obstacle
and cannot move
- There are detected pedestrians,
animals or objects at the front and
rear of the vehicle at the same time
- Approximately 3 minutes and 50
seconds have past after Smart Exit
function has started to operate
- The slope of the road exceeds the
operational range
- The function was paused for more
than 1 minute
- The steering wheel, gearshift,
braking, and drive controls are not
working properly
- ABS, TCS or ESC system operates
due to slippery road conditions
- The charging door is open
- The vehicle is utility mode
When Smart Exit function is cancelled,
the vehicle will automatically stop, shift
the gear to P (Park) and engage EPB
(Electronic Parking Brake).
Page 602 of 690
7-188
Driver Assistance System
[ Parking near a pillar
OJWEV071130N
Remote Smart Parking Assist
performance may reduce or collision
with an obstacle may occur when
there is a narrow object, circular pillar,
square pillar, or a pillar surrounded
by objects such as a fire extinguisher,
etc., near the parking space. The
driver should park the vehicle
properly.
[ Parking in a parking space with a
vehicle on one side only
OJWEV071126
If Remote Smart Parking Assist is
used, when parking in a parking space
with a vehicle only on one side, your
vehicle may cross the parking line to
avoid the parked vehicle.[ Leaving a parking space near a wall or
parking in a narrow space
OJWEV071131
- Remote Smart Parking Assist may
not operate properly when leaving
a parking space that is narrow
and near a wall. Always check for
pedestrians, animals, objects while
leaving.
- For your safety, Remote Smart
Parking Assist does not search for
parking spaces at areas with narrow
parking spaces that are narrower
than the minimum space required
for parking.
Page 607 of 690
8
Hazard Warning Flasher ................................................................................... 8-2
In Case of an Emergency While Driving .......................................................... 8-2
If the Vehicle Stalls while Driving ................................................................................ 8-2
If the Vehicle Stalls at a Crossroad or Crossing .......................................................... 8-2
If you have a Flat Tire while Driving ............................................................................8-3
If the Vehicle Will Not Start .............................................................................. 8-3
Jump Starting (12V Battery) ............................................................................. 8-4
Tire Pressure Monitoring System (TPMS) ........................................................ 8-8
Check Tire Pressure ..................................................................................................... 8-8
Tire Pressure Monitoring System ............................................................................... 8-9
Low Tire Pressure Warning Light ............................................................................... 8-10
Low Tire Pressure Position and Tire Pressure Telltale .............................................. 8-10
TPMS (Tire Pressure Monitoring System) malfunction indicator ............................. 8-11
Changing a Tire with TPMS ........................................................................................ 8-11
If you have a Flat Tire (with Tire Mobility Kit) ................................................. 8-13Introduction ................................................................................................................ 8-13
Notes on the Safe Use of the Tire Mobility Kit ......................................................... 8-14
Components of the Tire Mobility Kit ......................................................................... 8-15
Using the Tire Mobility Kit When a Tire is Flat .......................................................... 8-16
How to Adjust Tire Pressure ...................................................................................... 8-19
Towing ............................................................................................................. 8-20Towing Service .......................................................................................................... 8-20
Precautions when moving a Short Distance before Towing a Vehicle .................. 8-20
Removable Towing Hook ........................................................................................... 8-21
8. Emergency Situations