brake GENESIS GV60 2023 Service Manual

6-7
06
NOTICE
To prevent damage to the vehicle:
Do not press the Start/Stop button for
more than 10 seconds except when the
stop lamp fuse is blown.
When the stop lamp fuse is blown,
you cannot normally start the vehicle.
Replace the fuse with a new one. If you
are not able to replace the fuse, you
can start the vehicle by pressing and
holding the Start/Stop button for 10
seconds with the Start/Stop button in
the ACC position.
Pressing the brake pedal many times
while (
) indicator light is off will
increase the possibility of discharging
the 12V battery.
For your safety always depress the
brake pedal before starting the vehicle.
CAUTION

[Because the vehicle doesn't make
the vehicle sound, pay attention to
the surrounding environment and
drive carefully.

[After parking or waiting for a traffic
light, please check around(children,
obstacle, etc.) before departure.

[When reversing, check directly
behind you before driving.
Pedestrians may not be able to
recognize vehicle sounds.
OJWEV061009L
Information
If the smart key battery is weak or the
smart key does not work correctly, you
can start the vehicle by pressing the Start/
Stop button with the smart key in the
direction of the picture above.
Turning Off the Vehicle
1. Stop the vehicle and depress the
brake pedal fully.
2. Shift to P (Park).
3. Press the Start/Stop button to the OFF
position and apply the parking brake.
4. Make sure the (
) indicator light
is off in the instrument cluster.
CAUTION
If the () indicator light on the
instrument cluster is still on, the vehicle
is not turned off and can move when
the gear is in any position except P
(Park).

6-9
06
REDUCTION GEAR
„Crystal sphere mode
OJWEV061011
„Shift dial mode
OJWEV061012
[A]: Rotary shifter(Rotary gear shift dial),
[B] : P button,
[C] : P release cap
Reduction Gear Operation
Crystal sphere is a shift lever that can
be shifted to shift dial mode only while
the (
) indicator light is on in the
instrument cluster. If the vehicle is
not in a drivable state, maintain the
crystal sphere. Depress the brake pedal
whenever rotating the shift dial to
change gear or selecting P.
WARNING
To reduce the risk of serious injury or
death:

[ALWAYS check the surrounding
areas near your vehicle for people,
especially children, before shifting a
vehicle into D (Drive) or R (Reverse).

[Before leaving the driver's seat,
always make sure the vehicle is
shifted to the P (Park) position, then
apply the parking brake, then press
the Start/Stop button to the OFF
Position (confirm the crystal sphere
turns over). Unexpected and sudden
vehicle movement can occur if these
precautions are not followed.

6-11
06
Rotary shifter/ Rotary gear shift dial
P (Park)
Always come to a complete stop before
shifting into P (Park).
OJWEV061013
To shift the gear to P (Park), press the P
button while depressing the brake pedal.
If you turn the vehicle off in R (Reverse),
N (Neutral) or D (Drive), the gear will
automatically shift to P (Park).
WARNING

[Shifting into P (Park) while the
vehicle is in motion may cause you to
lose control of the vehicle.

[After the vehicle has stopped, always
make sure the vehicle is in P (Park),
apply the parking brake, and turn the
vehicle off.

[When parking on an incline, shift
the gear to P (Park) and apply the
parking brake to prevent the vehicle
from rolling downhill.Automatic gear shift to P (Park)
The gear is shifted to P (Park)
automatically for safety reasons under
the following conditions:

[When the vehicle is turned off with
the gear in R (Reverse), D (Drive) or N
(Neutral).

[When the driver’s door is open with
the vehicle running, the gear in R
(Reverse), D (Drive) or N (Neutral), and
the vehicle at a standstill.

[When the driver’s door is open with
the gear in N (Neutral) and the vehicle
is off.
In situations the gear must be in P (Park),
always check if the gear is shifted to P
(Park) by checking the cluster.

6-12
Driving Your Vehicle
R (Reverse)
Use this position to drive the vehicle
rearward.
OJWEV061016
To shift the gear to R (Rear), rotate the
rotary gear shift dial to R (Reverse) while
depressing the brake pedal.
When the vehicle is stopped in the
R (Reverse) position, if you open the
driver’s door, the gear will automatically
shift to P (Park).
However, if the vehicle is in motion, the
gear may not automatically shift to P
(Park) to prevent reduction gear damage.
The direction of the rotary gear shift dial
is the same as that of the wheel.
NOTICE
Always come to a complete stop before
shifting into or out of R (Reverse); you
may damage the reduction gear if you
shift into R (Reverse) while the vehicle is
in motion.
N (Neutral)
OJWEV061018
To shift the gear to N (Neutral), rotate the
shift dial clockwise from R (Reverse) or
counterclockwise from D (Drive) while
depressing the brake pedal.
Always depress the brake pedal when
you are shifting from N (Neutral) to
another gear.
If you turn the vehicle off in N (Neutral),
the gear will automatically shift to P
(Park).
However, if you need to stay in N
(Neutral) with the vehicle off, refer to “To
stay in N (Neutral) when vehicle is OFF”
in the following page.
CAUTION
The vehicle can be started with the gear
in N (Neutral), but for you safety, be
sure to start the vehicle with the gear in
P (Park).

6-13
06
To stay in N (Neutral) when vehicle is
OFF
ORG3EV061048L
OJWEV061068N
If you want to stay in N (Neutral) after the
vehicle is OFF (in the ACC state), do the
following.
1. Turn off Auto Hold and release
Electronic Parking Brake when the
vehicle is running.
2. Rotate the shift dial to N (neutral)
while depressing the brake pedal.
3. When you take your foot off the brake
pedal, the message ‘Press and hold
the OK Button on the steering Wheel
to stay in Neutral’ will appear on the
cluster LCD display.
4. Press and hold the OK button on
the steering wheel for more than 1
second.
5. When the message ‘Vehicle will stay in
(N). Change gear to cancel’ (or ‘N will
stay engaged when the vehicle is Off’)
will appear on the cluster LCD display,
press the Start/Stop button while
depressing the brake pedal.
However, if you open the driver's door,
the gear will automatically shift to P
(Park) and the Start/Stop button will
change to the OFF position.
NOTICE
With the gear in N (Neutral) the Start/
Stop button will be in the ACC position.
Note that the doors cannot be locked in
the ACC position or high voltage battery
may discharge if left in the ACC position
for a long period.

6-14
Driving Your Vehicle
D (Drive)
This is the normal driving position.
It automatically activates the
regenerative braking system according
to the road conditions.
OJWEV061017
To shift the gear to D (Drive), rotate the
rotary gear shift dial to D (Drive) while
depressing the brake pedal.
When the vehicle is stopped in the D
(Drive) position, if you open the driver's
door, the gear will automatically shift to
P (Park).
However, if the vehicle is in motion, the
gear may not automatically shift to P
(Park) to prevent reduction gear damage.
NOTICE
Always come to a complete stop before
shifting into D (Drive).
CAUTION
When you start after stopping on a steep
incline, even if the gear is in D (Drive),
if you do not depress the accelerator
or brake pedal, the vehicle may roll
backwards, which can cause an accident.
When the battery is discharged
You cannot shift gears, when the battery
is discharged.
In emergencies, do the following to shift
the gear to N (Neutral) on a level ground.
1. Connect the battery cables from
another vehicle or from a another
battery to the jump-starting terminals
inside the vehicle compartment.
For more details, refer to "Jump
Starting" section in chapter 8.
2. Release the Electronic Parking Brake
with the Start/Stop button in the ON
position.
OJWEV061054L
3. Remove the cap-cover (1) and press
the button (2) while depressing the
brake pedal.

6-15
06
Shift-lock system
For your safety, your vehicle has a
shiftlock system which prevents shifting
the gear from P (Park) or N (Neutral) into
R (Reverse) or D (Drive) unless the brake
pedal is depressed.
To shift from P (Park) or N (Neutral) into
R (Reverse) or D (Drive), from R (Reverse)
into D (Drive) or from D (Drive) into R
(Reverse) :
1. Depress and hold the brake pedal.
2. Start the vehicle.
3. Rotary the dial to the R (Reverse) or D
(Drive).
Information
For your safety, you cannot shift the gear
while the charging cable is connected.
Parking
Always come to a complete stop and
continue to depress the brake pedal.
Shift the gear to P (Park), apply the
parking brake, and press the Start/Stop
button to the OFF position. Take the Key
with you when leaving the vehicle.
LCD Display Messages (cluster)
Press brake pedal to change gear
OJWEV061001L
This message is displayed when the
brake pedal is not depressed while
shifting the gear.
Depress the brake pedal and then shift
the gear.
Shift to P after stopping
OJWEV061041L
This message is displayed when the gear
is shifted to P (Park) while the vehicle is
moving.
Stop the vehicle before shifting to P
(Park).

6-17
06
Shifter dial blocked. Please clear
obstructions
OJWEV061005L
This message is displayed when motion
is not possible due to obstacles around
the shift dial. Have to clean obstruction
around the shift dial.
Rotate the shift dial manually
OJWEV061004L
This message is displayed when the
driver tries to manually rotate the shift
dial in case of a malfunction of the shift
dial. Have the vehicle inspected by an
authorized retailer of Genesis Branded
products.
Good Driving Practices

[Never shift the gear from P (Park) or
N (Neutral) to any other position with
the accelerator pedal depressed.

[Never shift the gear into P (Park) when
the vehicle is in motion.
Be sure the vehicle is completely
stopped before you attempt to shift
into R (Reverse) or D (Drive).

[Do not shift the gear to N (Neutral)
when driving. If the gear is shifted to
N (Neutral) while driving. Doing so
may increase the risk of an accident.
Also, shift the gear back to D (Drive)
while the vehicle is moving may
severely damage the reduction gear.

[When driving uphill or downhill,
always shift to D (Drive) for driving
forward or shift to R (Reverse) for
driving backwards, and check the
gear position indicated on the cluster
or the rotary gear shift dial before
driving. Driving in the opposite
direction of the selected gear, can
lead to a dangerous situation by
shutting off the vehicle and affecting
the braking performance.

[Do not drive with your foot resting
on the brake pedal. Even light, but
consistent pedal pressure can result
in the brakes overheating, brake wear
and possibly even brake failure.

[Always apply the parking brake when
leaving the vehicle. Do not depend
on placing the shift gear in P (Park) to
keep the vehicle from moving.

6-19
06
Regenerative braking (Paddle
shifter)
OJWEV061020
The paddle shifter is used to adjust the
regenerative braking level from 0 to 3
during decelerating or braking.

[Left side (
): Increases regenerative
braking and deceleration.

[Right side (
): Decreases
regenerative braking and deceleration.

[Pull and hold the left side paddle
shifter for more than 0.5 seconds
and One pedal driving function is
operated, increasing the regenerative
braking. In this case, stopping the
vehicle is possible by keep on pulling
the paddle shifter.
Refer to the following pages on "One
pedal driving".

[Pull and hold the right side paddle
shifter for over 1 second to turn on
and off the automatic change of the
regenerative braking.
Refer to the following pages on
"Smart Recuperation System".
Information
The paddle shifter does not operate when:

[The [
] and [] paddle shifters are
pulled at the same time.

[The vehicle is decelerating by
depressing the brake pedal.

[Smart Cruise Control is activated.

[If level 0 is selected for the regenerative
braking system, the brake disc cleaning
function is operated. While operating
to clean the brake disc, the driving
distance and the regenerative braking
performance can be reduced. After
finishing, the regenerative braking
performance will be restored. The
brake disc cleaning function operates
when level 0 is re-selected after
adjusting the regenerative braking
level.
REGENERATIVE BRAKING SYSTEM

6-21
06
Limitations of One Pedal Driving
The vehicle may move even if one pedal
driving is normally operated. Therefore,
the driver should be careful to stop
the vehicle by this function under
circumstances as follows:
- Driving on Icy, snowy, wet, sandy,
muddy roads, manhole/pithole
surfaces
- Wheels not aligned
- Conditions in which wheel slip or spin
occurs
- On heavy loading
- By leaning left of right
- Under bad tire wear
- Driving uphill or downhill
- Driving where the slope starts or ends
- By repeating stop and go on ramp
Automatic engagement of EPB
After the vehicle is stopped by the
One Pedal Driving function, EPB is
automatically engaged when any of
these conditions occur:

[The driver’s seatbelt is unfastened and
the driver’s door is open.

[The gear shifts to N (Neutral)

[The hood is open.

[The liftgate is open.

[5 minutes have passed after the
vehicle has stopped.

[The system operation is limited due to
other reasons.
WARNING

[Stopping the vehicle may not be
possible according to the vehicle and
road conditions. Pay attention to the
road condition ahead and apply the
brake if necessary.

[Please refrain to use the one pedal
driving function with the road
conditions are bad such as being
wet, iced or covered with snow.
CAUTION
When the vehicle is stopped or parked by
One Pedal Driving on the steep hills, be
sure to depress the brake pedal.