GMC C-SERIES 1999 Owners Manual

yellowblue
6-43
Windshield Wiper Blade
Insert Replacement
Windshield wiper blades should be inspected at least
twice a year for wear or cracking. See ªWiper Blade
Checkº in Section 7 of this manual under Part B ªOwner
Checks and Servicesº for more information.
Replacement blades come in different types and are
removed in different ways.
Here's how to remove the Sheppard's Hook type:
1. Pull the windshield wiper arm away from
the windshield.
2. Push the release lever and slide the wiper assembly
toward the driver's side of the vehicle.
3. Install a new blade by reversing Steps 1 and 2.
ProCarManuals.com

yellowblue
6-44
Other Service Items
Component Box
Your vehicle has a component box along the left frame rail.
What is in the box depends on what options are on your
vehicle. Normally, the fuel filter, air dryer, Luberfiner oil
filter, emission canister or other components are in there.
To get into the box, you first have to remove the top
cover. To do that, remove the two 8 mm bolts on top and
the single 8 mm bolt at the top front. Then, pull the
cover toward you and lift it off.You can then remove the front cover if you need to, by
removing the two 8 mm bolts and pulling it off.
When you're through, be sure to put the front cover on,
before you put on the top cover.
Fuel Filter (Gasoline Engines)
The steel fuel filter is located inside the component box
at the rear. See your Maintenance Schedule for
recommended service intervals.
If your vehicle is equipped with the optional Davco
spin
-on type filter, it is also located in the component box.
ProCarManuals.com

yellowblue
6-45 Fuel Filter (Diesel Engines)
The ACDelco
fuel filter is located in the component
box. See your Maintenance Schedule for recommended
service intervals.
Primary Fuel Filter and Water Separator
(Option)
If you have a Caterpillar

diesel engine, you may
have this spin
-on filter.
It is in the component box
on the driver's side behind
the fender.
It has a clear plastic drain bowl at the bottom. Check the
drain bowl occasionally for any water or particles. To
drain the bowl, shut off the engine. Then partially open
the drain valve at the bottom of the filter. See ªEngine
Oilº in the Index for proper disposal procedures.
Secondary Fuel Filter and Water
Separator/Heater (Option)
If you have a Caterpillar

diesel engine, you may have
this spin
-on filter and fuel
separator/heater. It is
mounted on the passenger's
side of the engine.
It has a metal drain bowl at the bottom. Occasionally, check
the bowl for any water or particles. To check or drain the
bowl, shut off the engine. Then push up on the spring loaded
drain valve until clear fuel is flowing from the valve. The
particles or water will drain out first. See ªEngine Oilº in the
Index for proper disposal procedures.
ProCarManuals.com

yellowblue
6-46 Automatic Ether Injection System (Option)
If your diesel engine vehicle
has this feature, the ether
cylinder is on the upper
right rear side of the engine
compartment.
To change an empty ether cylinder, follow these steps.
1. Loosen the 5/16 inch screw head on the
cylinder
-to-bracket clamp.
2. Spread the clamp apart.3. Clean any dirt from the neck of the cylinder and the
top of the valve before you take out the cylinder.
4. Check the inside of the valve for any foreign matter.
Clean the valve as necessary.
5. Cover the valve to protect it from dirt and take out
the cylinder.
6. Install a new gasket whenever you take out the
cylinder. Use only one gasket and spread a light film
of clean oil on it before installation.
7. Put in the new cylinder. Turn it clockwise until it just
starts to contact the gasket.
8. Tighten the cylinder another half turn (180 degrees).
Don't over
-tighten.
9. Retighten the cylinder clamp.
ProCarManuals.com

yellowblue
6-47 Front Wheel Bearings with Oil-Filled Hubs
If your vehicle has oil-filled
hubs, occasionally check to
see if they have enough oil.
You can tell by looking into
the sight glass to see if there
is oil there.
If there isn't, clean the rubber fill plug in the center of
the glass, and then remove it. Be careful not to allow
any dirt or water to get into the oil. Add enough of the
recommended oil to bring it up to the level mark that
you'll see on the glass.
Refer to your Maintenance Schedule for the proper oil
to use.
When you fill the hub, check the glass again after
driving a short distance. It takes a while for the oil to
flow through the system, and you may find that you
have to add a little more to fill it to the proper level.
Air Conditioning System
Every now and then, have your dealership check your
air conditioning system to be sure it has not lost any
cooling ability. If you think the system is not working
properly, have your GM Truck dealer check it out as
soon as possible.
The air conditioning won't work when the temperature
outside is below 40
F (4
C).
NOTICE:
If your vehicle is equipped with factory air
conditioning, the system is charged with the
R
-134a refrigerant. Servicing of the air
conditioning system should be performed by a
trained service technician.
ProCarManuals.com

yellowblue
6-48 Muffler/Catalytic Converter Assemblies
(Diesel Engines)
Some vehicles equipped with a Caterpillar
diesel engine
utilize a catalytic converter
-muffler assembly. If your
vehicle is equipped with a catalytic converter
-muffler,
some special procedures may need to be followed when
servicing your vehicle. Consult your GM Truck dealer
who is an authorized Caterpillar

engine dealer
for service.
To determine your vehicle's muffler type, examine the
muffler outer housing. If your system is a catalytic
converter
-muffler type, the housing will be stamped
with the CAT logo.
Tires
Your new vehicle comes with high-quality tires made by
a leading tire manufacturer. If you ever have questions
about your tire warranty and where to obtain service, see
your GM Warranty booklet for details.
CAUTION:
Poorly maintained and improperly used tires
are dangerous.

Overloading your tires can cause
overheating as a result of too much friction.
You could have an air
-out and a serious
accident. See ªLoading Your Vehicleº in
the Index.

Underinflated tires pose the same danger as
overloaded tires. The resulting accident
could cause serious injury. Check all tires
frequently to maintain the recommended
pressure. Tire pressure should be checked
when your tires are cold.

Overinflated tires are more likely to be cut,
punctured or broken by a sudden
impact
-- such as when you hit a pothole.
Keep tires at the recommended pressure.

Worn, old tires can cause accidents. If your
tread is badly worn, or if your tires have
been damaged, replace them.
ProCarManuals.com

yellowblue
6-49 Inflation -- Tire Pressure
The Certification/Tire label, which is on the driver's
door, shows the correct inflation pressures for your tires
when they're cold. ªColdº means your vehicle has been
sitting for at least three hours or driven no more than
1 mile (1.6 km).
NOTICE:
Don't let anyone tell you that underinflation or
overinflation is all right. It's not. If your tires
don't have enough air (underinflation), you can
get the following:

Too much flexing

Too much heat

Tire overloading

Bad wear

Bad handling

Bad fuel economy.
NOTICE: (Continued)
NOTICE: (Continued)
If your tires have too much air (overinflation),
you can get the following:

Unusual wear

Bad handling

Rough ride

Needless damage from road hazards.
When to Check
Check your tires once a month or more. Also, check the
tire pressure of the spare tire.
How to Check
Use a good quality pocket
-type gage to check tire
pressure. You can't tell if your tires are properly inflated
simply by looking at them. Radial tires may look
properly inflated even when they're underinflated.
Be sure to put the valve caps back on the valve stems.
They help prevent leaks by keeping out dirt
and moisture.
ProCarManuals.com

yellowblue
6-50 Rims and Wheels
Rims and wheels are stamped with a maximum load and
cold inflation rating. Be sure you don't exceed these limits.
Dual Tire Operation
When the vehicle is new, or whenever a wheel, wheel
bolt or wheel nut is replaced, check the wheel nut torque
as indicated:
If your vehicle has stud piloted or hub piloted wheels,
tighten the wheel stud nuts to the specified torque values
at 100 miles (160 km), 500 miles (800 km) and
1,000 miles (1 600 km) and then every 1,000 miles
(1 600 km) thereafter.
For proper torque, see ªWheel Nut Torqueº in the Index.
The outer tire on a dual wheel setup generally wears
faster than the inner tire. Your tires will wear more
evenly and last longer if you rotate the tires periodically.
If you're going to be doing a lot of driving on
high
-crown roads, you can reduce tire wear by adding
5 psi (35 kPa) to the tire pressure in the outer tires. Be
sure to return to the recommended pressures when no
longer driving under those conditions. See ªChanging a
Flat Tireº in the Index for more information.
CAUTION:
If you operate your vehicle with a tire that is
badly underinflated, the tire can overheat. An
overheated tire can lose air suddenly or catch
fire. You or others could be injured. Be sure
all tires (including the spare, if any) are
properly inflated.
ProCarManuals.com

yellowblue
6-51 When It's Time for New Tires
Replace your tires when the tread depth is down to
1/8 of an inch (3.2 mm) for the front tires, or 1/16 of
an inch (1.6 mm) for a rear tire. Also, you need a new
tire if:

You can see cord or fabric showing through the
tire's rubber.

The tread or sidewall is cracked, cut or snagged deep
enough to show cord or fabric.

The tire has a bump, bulge or split.

The tire has a puncture, cut or other damage that
can't be repaired well because of the size or location
of the damage.
CAUTION:
Mixing tires could cause you to lose control while
driving. If you mix tires of different types
-- like
radial and bias
-belted tires -- the vehicle may not
handle properly, and you could have a crash.
Be sure to use the same type of tires all around.
When you replace tires, make sure they are the same
size, load range, speed rating and construction type
(bias, bias
-belted or radial) as your original tires.
Wheel Alignment and Tire Balance
The wheels on your vehicle were aligned at the
factory to give you the longest tire life and best
overall performance.
Proper front wheel alignment must be maintained in
order to ensure efficient steering, good directional
stability, and prevent abnormal tire wear. If you notice
unusual tire wear or your vehicle is pulling one way or
the other, the alignment may need to be reset. If you
notice your vehicle vibrating when driving on a smooth
road, your wheels may need to be balanced.
ProCarManuals.com

yellowblue
6-52 Tightening the Wheel Nuts
CAUTION:
Wheel nuts that are not tight can work loose. If
all the nuts on a wheel come off, the wheel can
come off the vehicle, causing a serious crash. All
wheel nuts must be properly tightened. Follow
the rules in this section to be sure they are.
This section lets you know how often to check the
tightness of the wheel nuts on your vehicle and how
tight they must be.
First, use these pictures to decide what kind of wheels
you have.
Hub-Piloted Type,
8
-HoleHub
-Piloted Type,
10
-Hole
Stud-Piloted Type, 10-Hole
ProCarManuals.com