oil GMC C-SERIES 1999 Owner's Guide

yellowblue
6-41
Tandem Axle ModelsITEM
NO.ITEM REMARKS
1 Brake Camshafts One fitting each.
2 Propshaft U
-Joint One fitting each joint
(1480 and 1550 Series).
Lubricate with GM Part
No. 1051344, Wheel
Bearing Lubricant.
4 Brake Shoe
Roller PinsApply engine oil at pin
to shoe joint only.
5 Rear Spring Pin One fitting each side.
6 Wheel Bearings Hand
-pack or lubricate.
7 Rear Axles Fill to level of filler plug.
8 Propshaft Slip
JointTwo fittings each side.
Lubricate with GM Part
No. 1051344 Wheel
Bearing Lubricant.
ProCarManuals.com

yellowblue
6-44
Other Service Items
Component Box
Your vehicle has a component box along the left frame rail.
What is in the box depends on what options are on your
vehicle. Normally, the fuel filter, air dryer, Luberfiner oil
filter, emission canister or other components are in there.
To get into the box, you first have to remove the top
cover. To do that, remove the two 8 mm bolts on top and
the single 8 mm bolt at the top front. Then, pull the
cover toward you and lift it off.You can then remove the front cover if you need to, by
removing the two 8 mm bolts and pulling it off.
When you're through, be sure to put the front cover on,
before you put on the top cover.
Fuel Filter (Gasoline Engines)
The steel fuel filter is located inside the component box
at the rear. See your Maintenance Schedule for
recommended service intervals.
If your vehicle is equipped with the optional Davco
spin
-on type filter, it is also located in the component box.
ProCarManuals.com

yellowblue
6-45 Fuel Filter (Diesel Engines)
The ACDelco
fuel filter is located in the component
box. See your Maintenance Schedule for recommended
service intervals.
Primary Fuel Filter and Water Separator
(Option)
If you have a Caterpillar

diesel engine, you may
have this spin
-on filter.
It is in the component box
on the driver's side behind
the fender.
It has a clear plastic drain bowl at the bottom. Check the
drain bowl occasionally for any water or particles. To
drain the bowl, shut off the engine. Then partially open
the drain valve at the bottom of the filter. See ªEngine
Oilº in the Index for proper disposal procedures.
Secondary Fuel Filter and Water
Separator/Heater (Option)
If you have a Caterpillar

diesel engine, you may have
this spin
-on filter and fuel
separator/heater. It is
mounted on the passenger's
side of the engine.
It has a metal drain bowl at the bottom. Occasionally, check
the bowl for any water or particles. To check or drain the
bowl, shut off the engine. Then push up on the spring loaded
drain valve until clear fuel is flowing from the valve. The
particles or water will drain out first. See ªEngine Oilº in the
Index for proper disposal procedures.
ProCarManuals.com

yellowblue
6-46 Automatic Ether Injection System (Option)
If your diesel engine vehicle
has this feature, the ether
cylinder is on the upper
right rear side of the engine
compartment.
To change an empty ether cylinder, follow these steps.
1. Loosen the 5/16 inch screw head on the
cylinder
-to-bracket clamp.
2. Spread the clamp apart.3. Clean any dirt from the neck of the cylinder and the
top of the valve before you take out the cylinder.
4. Check the inside of the valve for any foreign matter.
Clean the valve as necessary.
5. Cover the valve to protect it from dirt and take out
the cylinder.
6. Install a new gasket whenever you take out the
cylinder. Use only one gasket and spread a light film
of clean oil on it before installation.
7. Put in the new cylinder. Turn it clockwise until it just
starts to contact the gasket.
8. Tighten the cylinder another half turn (180 degrees).
Don't over
-tighten.
9. Retighten the cylinder clamp.
ProCarManuals.com

yellowblue
6-47 Front Wheel Bearings with Oil-Filled Hubs
If your vehicle has oil-filled
hubs, occasionally check to
see if they have enough oil.
You can tell by looking into
the sight glass to see if there
is oil there.
If there isn't, clean the rubber fill plug in the center of
the glass, and then remove it. Be careful not to allow
any dirt or water to get into the oil. Add enough of the
recommended oil to bring it up to the level mark that
you'll see on the glass.
Refer to your Maintenance Schedule for the proper oil
to use.
When you fill the hub, check the glass again after
driving a short distance. It takes a while for the oil to
flow through the system, and you may find that you
have to add a little more to fill it to the proper level.
Air Conditioning System
Every now and then, have your dealership check your
air conditioning system to be sure it has not lost any
cooling ability. If you think the system is not working
properly, have your GM Truck dealer check it out as
soon as possible.
The air conditioning won't work when the temperature
outside is below 40
F (4
C).
NOTICE:
If your vehicle is equipped with factory air
conditioning, the system is charged with the
R
-134a refrigerant. Servicing of the air
conditioning system should be performed by a
trained service technician.
ProCarManuals.com

yellowblue
6-54
Stud-Piloted 10-Stud Wheel
The studs and nuts used on the right side of the vehicle
have right
-hand threads. Those used on the left side
have left
-hand threads. It is easy to tell by looking at the
nuts, because they are stamped R or L.
1. Put the tire and rim assembly on the axle hub.
2. Put on the wheel nuts. If you use oil or grease on the
wheel studs or nuts, the wheel nuts can't tighten
properly. This could let the wheel come off as you
are driving.
3. Finger
-tighten the nuts on the rear inner wheels and
the front wheels.
4. Tighten these nuts to 575 lb
-ft (780 N´m), unless
you have aluminum wheels and/or aluminum hubs.
If you have aluminum wheels and/or aluminum
hubs, tighten the nuts only to 475 lb
-ft (644 N´m).
Use the following diagram to do this.
Front or Inner Dual
WheelOuter Dual Wheel
5. Install the outer rear tire and rim assembly so that its
valve stem is exactly opposite the valve stem on the
inner tire and rim assembly.
6. Put on the wheel nuts.
7. Finger
-tighten the wheel nuts.
8. Tighten the nuts to the same torque numbers shown
in Step 4.
Whenever tightening both the inner and outer rear wheel
nuts, first loosen the outer wheel nuts. Then tighten the
inner nuts. Finally, tighten the outer nuts.
ProCarManuals.com

yellowblue
6-55
CAUTION:
Never use oil or grease on studs or nuts. If you
do, the nuts might come loose. Your wheel could
fall off, causing a serious accident.
Hub-Piloted Wheels, 8-Hole or 10-Hole
The studs and nuts used with these wheels have
right
-hand threads.
1. With intermittent pilot pads, position a pad at
12 o'clock to center the wheel and reduce run
-out.
2. Put the tire and rim assembly on the axle hub. Install
the outer rear tire and rim assembly so that its valve
stem is exactly opposite the valve stem on the inner
tire and rim assembly.
3. Put on the wheel nuts.
4. Finger
-tighten the nuts.
5. Oil the surfaces between
the nuts and washers as
shown. Do not oil the
studs or the threads of
the nut.
ProCarManuals.com

yellowblue
6-59
Appearance Care
Remember, cleaning products can be hazardous. Some
are toxic. Others can burst into flame if you strike a
match or get them on a hot part of the vehicle. Some are
dangerous if you breathe their fumes in a closed space.
When you use anything from a container to clean your
vehicle, be sure to follow the manufacturer's warnings
and instructions. And always open your doors or
windows when you're cleaning the inside.
Never use these to clean your vehicle:

Gasoline

Benzene

Naphtha

Carbon Tetrachloride

Acetone

Paint Thinner

Turpentine

Lacquer Thinner

Nail Polish Remover
They can all be hazardous
-- some more than others --
and they can all damage your vehicle, too.Don't use any of these unless this manual says you can.
In many uses, these will damage your vehicle:

Alcohol

Laundry Soap

Bleach

Reducing Agents
Cleaning the Inside of Your Vehicle
Use a vacuum cleaner often to get rid of dust and loose
dirt. Wipe vinyl, leather, plastic and painted surfaces
with a clean, damp cloth.
Cleaning of Fabric/Carpet
Your dealer has two cleaners, Multi-Purpose Interior
Cleaner and Capture Non
-Solvent Dry Spot and Soil
Remover for cleaning fabric and carpet. They will clean
normal spots and stains very well. You can get
GM
-approved cleaning products from your dealer.
(See ªAppearance Care and Materialsº in the Index.)
Here are some cleaning tips:

Always read the instructions on the cleaner label.

Clean up stains as soon as you can
-- before they set.

Carefully scrape off any excess stain.
ProCarManuals.com

yellowblue
6-60

Use a clean cloth or sponge, and change to a
clean area often. A soft brush may be used if stains
are stubborn.

If a ring forms on fabric after spot cleaning, clean the
entire area immediately or it will set.
Using Multi-Purpose Interior Cleaner
on Fabric
1. Vacuum and brush the area to remove any loose dirt.
2. Always clean a whole trim panel or section. Mask
surrounding trim along stitch or welt lines.
3. Mix powdered cleaner following the directions on
the container label to form thick suds.
4. Use suds only and apply with a clean sponge. Don't
saturate the material and don't rub it roughly.
5. As soon as you've cleaned the section, use a sponge
to remove the suds.
6. Wipe cleaned area with a clean, damp towel or cloth.
7. Wipe with a clean cloth and let dry.
Special Fabric Cleaning Problems
Stains caused by such things as catsup, coffee (black),
egg, fruit, fruit juice, milk, soft drinks, vomit, urine and
blood can be removed as follows:
1. Carefully scrape off excess stain, then sponge the
soiled area with cool water.
2. If a stain remains, follow the multi
-purpose interior
cleaner instructions described earlier.
3. If an odor lingers after cleaning vomit or urine,
treat the area with a water/baking soda solution:
1 teaspoon (5 ml) of baking soda to 1 cup (250 ml)
of lukewarm water.
4. Let dry.
Stains caused by candy, ice cream, mayonnaise, chili
sauce and unknown stains can be removed as follows:
1. Carefully scrape off excess stain.
2. First, clean with cool water and allow to
dry completely.
3. If a stain remains, follow instructions for
Multi
-Purpose Interior Cleaner.
ProCarManuals.com

yellowblue
6-61 Fabric Protection
Your vehicle has upholstery that has been treated with
Scotchgard Fabric Protector, a 3M product. It protects
fabrics by repelling oil and water, which are the carriers
of most stains. Even with this protection, you still need
to clean your upholstery often to keep it looking new.
Further information on cleaning is available by calling
1
-800-433-3296 (in Minnesota, 1-800-642-6167).
Cleaning Vinyl
Use warm water and a clean cloth.

Rub with a clean, damp cloth to remove dirt. You
may have to do it more than once.

Things like tar, asphalt and shoe polish will stain
if you don't get them off quickly. Use a clean cloth
and a vinyl/leather cleaner. See your dealer for
this product.
Cleaning the Top of the Instrument Panel
Use only mild soap and water to clean the top surfaces
of the instrument panel. Sprays containing silicones or
waxes may cause annoying reflections in the windshield
and even make it difficult to see through the windshield
under certain conditions.
Cleaning Interior Plastic Components
Use only a mild soap and water solution on a soft
cloth or sponge. Commercial cleaners may affect the
surface finish.
Care of Safety Belts
Keep belts clean and dry.
CAUTION:
Do not bleach or dye safety belts. If you do, it
may severely weaken them. In a crash, they
might not be able to provide adequate protection.
Clean safety belts only with mild soap and
lukewarm water.
ProCarManuals.com