wheel GMC C-SERIES 1999 Repair Manual

yellowblue
7-13 72,000 Miles (120 000 km)

Engine oil and filter service. (3)(9)

Check fluid levels (or every 3 months, whichever
occurs first). (1)(2)(6)

Chassis lubrication service (or every 6 months,
whichever occurs first). (12)

Inspect door hinge pins and bushings and replace as
necessary. Lubricate door hinge pins and rollers with
engine oil.

Replace air conditioning filter dryer (or every
18 months, whichever occurs first, and whenever
refrigerant charge is lost for any reason).

Wheel bearing (grease type) service (or every
24 months, whichever occurs first, and whenever
hubs are removed). (23)

Wheels and tires service. (15)

Hydraulic brake service (or every 6 months,
whichever occurs first). (7)

Hydraulic brake caliper service (or every 6 months,
whichever occurs first). (22)

Hydraulic parking brake service (or every 6 months,
whichever occurs first). (8)

Engine drive belts service (or every 12 months,
whichever occurs first). (18)

Clutch pedal free travel service. (10)
Throttle linkage service. (19)

Thermostatically controlled engine cooling
fan service. (4)(20)

Shields and underhood insulation service. (4)(5)(21)

Air intake system service (or every 24 months,
whichever occurs first). (4)(5)(24)

Thermostatically controlled air cleaner service (or
every 24 months, whichever occurs first). (3)(4)(25)

Fuel tank, fuel cap and fuel lines service (or every
72 months, whichever occurs first). (3)(30)

EGR system inspection (or every 72 months,
whichever occurs first). (3)(31)
Electronic Vacuum Regulator Valve (EVRV)
inspection (or every 72 months, whichever occurs
first). (3)(32)
Evaporative Control System Service (if equipped)
(or every 24 months, whichever occurs first).
(3)(26)

Rear axle air shift motor service. (11)
Check air brake relay valve operation and check for
leaks (or every month, or every 300 hours,
whichever occurs first).
(Continued)
ProCarManuals.com

yellowblue
7-14 72,000 Miles (120 000 km) (Continued)

Clean air brake application valve (or every 3 months,
or every 300 hours, whichever occurs first);
lubricate linkage.

Air brake chamber service (or every 2 months,
whichever occurs first). (41)

Trailer brake hand control valve service (or every
3 months, or 900 hours, whichever occurs first). (42)
75,000 Miles (125 000 km)

Engine oil and filter service. (3)(9)

Check fluid levels (or every 3 months, whichever
occurs first). (1)(2)(6)

Steering system service. (13)

Front and rear suspension service. (14)

Spring
-to-axle U-bolts and shackle bolts service. (16)

Exhaust system service (or every 6 months,
whichever occurs first). (3)(4)(17)

Air brake service (or every 6 months, whichever
occurs first). (39)
78,000 Miles (130 000 km)

Engine oil and filter service. (3)(9)

Check fluid levels (or every 3 months, whichever
occurs first). (1)(2)(6)
Chassis lubrication service (or every 6 months,
whichever occurs first). (12)

Lubricate door hinge pins and rollers with engine oil.

Wheels and tires service. (15)

Hydraulic brake service (or every 6 months,
whichever occurs first). (7)

Hydraulic parking brake service (or every 6 months,
whichever occurs first). (8)

Clutch pedal free travel service. (10)
81,000 Miles (135 000 km)

Engine oil and filter service. (3)(9)

Check fluid levels (or every 3 months, whichever
occurs first). (1)(2)(6)

Wheel bearings service
-- Eaton Axle (oil-filled) (or
every 24 months, whichever occurs first). (1)(23)
84,000 Miles (140 000 km)

Engine oil and filter service. (3)(9)

Check fluid levels (or every 3 months, whichever
occurs first). (1)(2)(6)

Chassis lubrication service (or every 6 months,
whichever occurs first). (12)

Lubricate door hinge pins and rollers with engine oil.

Wheels and tires service. (15)
ProCarManuals.com

yellowblue
7-15

Hydraulic brake service (or every 6 months,
whichever occurs first). (7)

Hydraulic parking brake service (or every 6 months,
whichever occurs first). (8)

Engine drive belts service (or every 12 months,
whichever occurs first). (18)

Clutch pedal free travel service. (10)

Throttle linkage service. (19)

Thermostatically controlled engine cooling
fan service. (4)(20)

Shields and underhood insulation service. (4)(5)(21)

Check air brake relay valve operation and check for
leaks (or every month, or every 300 hours,
whichever occurs first).
87,000 Miles (145 000 km)

Engine oil and filter service. (3)(9)

Check fluid levels (or every 3 months, whichever
occurs first). (1)(2)(6)
90,000 Miles (150 000 km)

Engine oil and filter service. (3)(9)

Check fluid levels (or every 3 months, whichever
occurs first). (1)(2)(6)

Chassis lubrication service (or every 6 months,
whichever occurs first). (12)
Replace fuel filter(s) (or every 12 months, whichever
occurs first). (3)

Air cleaner filter replacement service (or every
24 months, whichever occurs first). (3)(4)(27)

Steering system service. (13)

Front and rear suspension service. (14)

Spring
-to-axle U-bolts and shackle bolts service. (16)

Exhaust system service (or every 6 months,
whichever occurs first). (3)(4)(17)

Air brake service (or every 6 months, whichever
occurs first). (39)

Inspect door hinge pins and bushings and replace as
necessary. Lubricate door hinge pins and rollers with
engine oil.

Replace air conditioning filter dryer (or every
18 months, whichever occurs first, and whenever
refrigerant charge is lost for any reason).

Wheels and tires service. (15)

Hydraulic brake service (or every 6 months,
whichever occurs first). (7)

Hydraulic brake caliper service (or every 6 months,
whichever occurs first). (22)

Hydraulic parking brake service (or every 6 months,
whichever occurs first). (8)
(Continued)
ProCarManuals.com

yellowblue
7-16 90,000 Miles (150 000 km) (Continued)

Clutch pedal free travel service. (10)

Air brake automatic slack adjuster service (or every
500 hours, whichever occurs first). (40)

Clean air brake application valve (or every 3 months,
or every 300 hours, whichever occurs first);
lubricate linkage.
93,000 Miles (155 000 km)

Engine oil and filter service. (3)(9)

Check fluid levels (or every 3 months, whichever
occurs first). (1)(2)(6)
96,000 Miles (160 000 km)

Engine oil and filter service. (3)(9)

Check fluid levels (or every 3 months, whichever
occurs first). (1)(2)(6)

Chassis lubrication service (or every 6 months,
whichever occurs first). (12)

Lubricate door hinge pins and rollers with engine oil.

Wheel bearing (grease type) service (or every
24 months, whichever occurs first, and whenever
hubs are removed). (23)

Wheels and tires service. (15)

Hydraulic brake service (or every 6 months,
whichever occurs first). (7)
Hydraulic parking brake service (or every 6 months,
whichever occurs first). (8)

Engine drive belts service (or every 12 months,
whichever occurs first). (18)

Clutch pedal free travel service. (10)

Throttle linkage service. (19)

Thermostatically controlled engine cooling
fan service. (4)(20)

Shields and underhood insulation service. (4)(5)(21)

Air intake system service (or every 24 months,
whichever occurs first). (4)(5)(24)

Thermostatically controlled air cleaner service (or
every 24 months, whichever occurs first).
(3)(4)(25)

Evaporative Control System Service (if equipped)
(or every 24 months, whichever occurs first).
(3)(26)

Rear axle air shift motor service. (11)
Check air brake relay valve operation and check for
leaks (or every month, or every 300 hours,
whichever occurs first).
Air brake chamber service (or every 2 months,
whichever occurs first). (41)
Trailer brake hand control valve service (or every
3 months, or 900 hours, whichever occurs first). (42)
ProCarManuals.com

yellowblue
7-17 99,000 Miles (165 000 km)

Engine oil and filter service. (3)(9)

Check fluid levels (or every 3 months, whichever
occurs first). (1)(2)(6)
100,000 Miles (166 000 km)

Change power steering fluid (or every 36 months,
whichever occurs first). (13)

Front axle service (or every 36 months, whichever
occurs first). (38)

Rear axle service
-- Eaton, Rockwell, Spicer Axles
(or every 12 months, whichever occurs first). (1)(37)

Exhaust brake service (if equipped). Check for
excessive spindle free play and smooth operation.
Lubricate ball joint cap.

Accelerator control cable replacement (diesel) (or
every 36 months, whichever occurs first). (19)

Air brake service (or every 12 months, or
3,600 hours, whichever occurs first). (44)
150,000 Miles (240 000 km)

Cooling system service (or every 60 months since
last service, whichever occurs first). (3)(35)
200,000 Miles (320 000 km)

Remove, disassemble, clean and inspect the air brake
trailer supply valve (or every 2 years, or 7,200 hours,
whichever occurs first).
250,000 Miles (400 000 km)

Wheel bearings service -- Eaton Axle (oil-filled) (or
every 36 months, whichever occurs first). (2)(23)

Rear axle service
-- Eaton, Rockwell, Spicer Axles
(or every 36 months, whichever occurs first). (2)(37)

Manual transmission fluid replacement (or every
60 months, whichever occurs first).
300,000 Miles (480 000 km)

Remove, disassemble, clean and inspect the air brake
air dryer (or every 3 years, or 10,800 hours,
whichever occurs first). Replace dessicant on
Bendix
-Westinghouse units.
ProCarManuals.com

yellowblue
7-19
(10) = Check clutch pedal for free travel. Press pedal
by hand until resistance is felt. Free travel should be
maintained at 1.5 to 2 inches (38 to 51 mm) measured
at the clutch pedal pad. Make checks at 3,000 miles
(5 000 km) and 6,000 miles (10 000 km) and then every
6,000 miles (10 000 km) thereafter.
(11) = Inspect rear axle air shift motor for fluid leaks.
Remove plug to check fluid level. Inspect air lines and
hoses for proper hook
-up, binding, leaks, etc. Inspect at
3,000 miles (5 000 km) and 24,000 miles (40 000 km)
and then every 24,000 miles (40 000 km) thereafter.
(12) = Chassis Lubrication Service: Lubricate all grease
fittings in front suspension, front axle and steering
linkage. DO NOT lubricate kingpin bushings with air
pressure equipment; instead, use a hand grease gun to
ensure complete purge and eliminate sealer cap
distortion. Lubricate transmission and shift linkage,
hood latches and hood hinges, parking brake lever pivot,
clevis pins and linkage, disc brake caliper rails, clutch
linkage and release bearing (if equipped), propeller shaft
slip joint, universal joint, brake camshaft bracket, slack
adjusters, pedal shaft, clutch cross shaft and clutch pedal
springs. Lubricate suspension, axle and steering linkage
more often when operating under dusty or muddy
conditions and in excessive off
-road use.(13) = Check steering system:

Look for damaged, loose or missing parts. Also
look for parts showing signs of wear or lack of
lubrication. Replace parts as needed. Also check
steering gear mounting bolts, pitman arm nut, gear
housing upper cover and side cover attaching bolts,
steering column mounting bolts and cardan
joint clamp bolts; tighten if necessary.
(See service manual.)

Inspect power steering hoses, tubes and fittings for
leaks. Hoses and lines must not be twisted, kinked or
tightly bent. Make sure clips, clamps, supporting
tubes and hoses are in place and properly secured.

Check steering gear for leakage around pitman shaft
and housing. If leakage is evident (lubricant
oozing out, not just oily film), leak should be
corrected immediately.
(14) = Check front and rear suspension. Look for
damaged, loose or missing parts or parts showing signs
of wear or lack of lubrication. Replace parts as needed.
(15) = Adjust tire pressures as indicated on the
Certification/Tire label for optimum tire life. See ªTiresº
in the Index for further details. Check tires for excessive
or abnormal wear or damage. Also check for damaged
wheels. Replace wheels and/or tires as needed.
ProCarManuals.com

yellowblue
7-20
(16) = Check spring-to-axle U-bolts and shackle bolts
for proper torque. See the service manual for torque
sequence and specifications. When parts are replaced,
the torque must be checked and adjusted more often
during the first 6,000 miles (10 000 km). Check torque
at 500 miles (800 km) and 2,000 miles (3 000 km) after
first use of parts.
(17) = Check complete exhaust system and cab areas
near the exhaust system for broken, damaged, missing or
out
-of-position parts. Also inspect for open seams,
holes, loose connections or other conditions which could
let exhaust fumes seep into the driver compartment.
Needed repairs should be made at once. To help
maintain system integrity, replace exhaust pipes
whenever a new muffler is put on.
(18) = Check all engine drive belts for cracks, fraying,
wear and proper tension. Adjust or replace as needed.
(19) = Check throttle linkage for damaged or missing
parts (including throttle return springs), interference or
binding. Fix any problems at once. Do not lubricate
accelerator and cruise control cables.
(20) = With the engine off and below normal operating
temperature, check to see that the thermostatically
controlled engine cooling fan can be rotated by hand on
viscous
-operated drives. Replace as needed.(21) = Check shields and underhood insulation for
damage or looseness. Adjust or replace as needed.
(22) = Lubricate caliper housing, caliper support spring
and caliper support key.
(23) = Wheel bearing service:

Grease type
-- Clean, inspect and lubricate with the
proper wheel bearing grease at designated intervals
or when hubs are removed. See ªRecommended
Fluids and Lubricantsº in the Index.

Oil
-filled type -- Some wheel bearings are lubricated
by rear axle lubricant. When you have oil
-filled
hubs, use lubricant identical to that used in your rear
axle. Lubricant change intervals are the same for
front and rear axles. However, you must maintain oil
level at the OIL LEVEL mark between change
intervals. See ªRecommended Fluids and
Lubricantsº in the Index.
(24) = Check the air intake system installation to see
that gaskets are seated properly and all hose
connections, fasteners and other components are tight.
For gasoline engines, also check to be sure the air
cleaner housing is properly seated, that the cover fits
tightly and that the wing nut is tight. Tighten
connections and fasteners or replace parts as required.
ProCarManuals.com

yellowblue
7-21
(25) = Check thermostatically controlled air cleaner
installation to make certain that all ducts are connected and
correctly installed. Also, check valve for proper operation.
(26) = Evaporative Control System Service (if equipped):
Check all fuel and vapor lines and hoses for proper
connections and correct routing (or every 24 months,
whichever occurs first). Replace parts as needed.
(27) = Replace air cleaner filter (or every 24 months,
whichever occurs first). Replace filter more often if
driving in dusty conditions. Ask your dealer for the
proper replacement intervals for your driving conditions.
(28) = Replace spark plugs. Inspect wires for damage.
Check the wire boot and boot heat shield fit at spark
plugs and coil. Replace parts as needed.
(30) = Check the fuel tank, fuel cap and fuel lines for
damage which could cause leakage. Inspect fuel cap for
correct sealing ability and any indications of damage.
Check fuel cap gasket for even filler neck imprint.
Replace parts as needed.
(31) = Check EGR system as described in the service
manual. See ªService and Owner Publicationsº in the Index.
(32) = Inspect Electronic Vacuum Regulator Valve
(EVRV) filter for excessive contamination or plugging.
If needed, clean filter with solution of soap and water,
let dry and install.(33) = Check the PCV system for proper operation and
clean PCV valve. Replace hoses as needed.
(34) = Replace PCV valve and blow out the PCV valve
hose with compressed air. Replace hoses as needed.
(35) = Drain, flush and refill cooling system. See
ªRecommended Fluids and Lubricantsº in the Index for
what to use. Inspect hoses. Clean radiator, condenser,
pressure cap and neck. Pressure test cooling system and
pressure cap. For Caterpillar
 diesel engines, always refer
to the Caterpillar Diesel Engine Operation & Maintenance
Manual for coolant recommendations and change intervals.
(37) = Rear axle service: Change the lubricant. See
ªRecommended Fluids and Lubricantsº in the Index.
(38) = Front axle service: Re
-pack upper kingpin
roller bearing.
(39) = Air brake service:

Inspect brake lines and hoses for proper hook
-up,
binding, leaks, cracks, chafing, etc. Inspect drum
brake linings for wear or cracks. Inspect other brake
parts at each wheel, including drums, wheel cylinders
and piston heat shields and boots. Check brake pedal
for excessive free play or travel (or every 6 months,
whichever occurs first) and have serviced if needed.
Check brakes more often if driving habits and
conditions result in frequent braking.
ProCarManuals.com

yellowblue
7-22

Test air lines for leaks; tighten as needed. Replace
compressor filter.

Inspect air parking brake chamber for leaks and
damage. Inspect lines and hoses for leaks, cracks,
chafing, etc. Also check all attachments for
tightness, wear or damage. Note: The spring brake
section of the rear brake diaphragms are
non
-serviceable.

Replace the air compressor filter element, mounted
on the air compressor. For remote air compressor
intake service, refer to air cleaner filter replacement.
(40) = Clean and lubricate air brake automatic slack
adjuster. Check pushrod travel and auto adjustment
operation. Have serviced if needed.
(41) = Air brake chamber service: Check operation,
mounting, clamps and air lines and check for leaks.
(42) = Trailer brake hand control valve service: Check
operation; lubricate cam and follower.
(44) = Air brake service: Remove, disassemble, clean
and inspect the safety valve, standard brake chamber,
quick release valve, quick release/double check valve
combination, parking brake control valve, double check
valve, pressure protection valve and alcohol injector. Remove, disassemble and clean the application valve;
replace parts showing wear. Remove, disassemble, clean
and inspect the spring brake control valve; replace
rubber parts.
(45) = For Stud Piloted Wheels Only: Tighten the wheel
stud nuts to the specified torque values at 100 miles
(160 km), 500 miles (800 km) and 1,000 miles
(1 600 km) and then every 1,000 miles (1 600 km)
thereafter. See ªTightening the Wheel Nutsº in
the Index.
(46) = For Hub Piloted Wheels Only: Tighten the wheel
stud nuts to the specified torque values at 1,000 miles
(1 600 km). Thereafter, tighten them 1,000 miles
(1 600 km) after each time the wheel is removed. See
ªTightening the Wheel Nutsº in the Index.
(47) = Short Trip/City Maintenance Schedule. See
ªMaintenance Schedule Definitionº in the introduction
pages at the beginning of this section.
(48) = Long Trip/Highway Maintenance Schedule. See
ªMaintenance Schedule Definitionº in the introduction
pages at the beginning of this section.
ProCarManuals.com

yellowblue
7-25
Starter Switch Check
CAUTION:
When you are doing this check, the vehicle could
move suddenly. If it does, you or others could be
injured. Follow the steps below.
1. Before you start, be sure you have enough room
around the vehicle.
2. Firmly apply both the parking brake (see ªParking
Brakeº in the Index if necessary) and the
regular brakes.
NOTE: Do not use the accelerator pedal, and be
ready to turn off the engine immediately if it starts.
3. On automatic transmission vehicles, try to start the
engine in each gear. The starter should work only in
PARK (P), if equipped, or NEUTRAL (N). If the
starter works in any other position, your vehicle
needs service.Automatic Transmission Shift Indicator Check
Check that the indicator points to the gear chosen.
Steering Check
Be alert for any changes in steering action, abnormal
front tire wear or steering wheel position. An inspection
or service is needed when the steering wheel is harder to
turn or has too much free play, or if there are strange
sounds when turning or parking.
Brake System Check
Be alert to illumination of the low air warning lamp or
for the tone alarm, or changes in braking action, such as
repeated pulling to one side, unusual sounds when
braking or increased brake pedal travel. Make sure air
brake system reservoirs are drained daily with full
system air pressure, and check system for leaks. Any of
these conditions could indicate the need for brake
system inspection and/or service.
ProCarManuals.com