stop start GMC C-SERIES 1999 Owners Manual

yellowblue
1-15

You can add a small amount of slack. The system
works like a window shade. To add a little slack, pull
down on the shoulder belt just a little
-- no more
than 1 inch (25 mm).

If it's now too loose, pull it out like you did before
and start again.

If you move around in the vehicle and your shoulder
belt becomes loose, be sure to make it tight again.
The lap part of the belt should be worn low and snug on
the hips, just touching the thighs. In a crash, this applies
force to the strong pelvic bones. And you'd be less likely
to slide under the lap belt. If you slid under it, the belt
would apply force at your abdomen. This could cause
serious or even fatal injuries. The shoulder belt should go
over the shoulder and across the chest. These parts of the
body are best able to take belt restraining forces.
The safety belt locks if there's a sudden stop or a crash.
ProCarManuals.com

yellowblue
2-5 Leaving Your Vehicle
If you are leaving the vehicle, take your keys, open your
door and set the locks from inside. Then get out and
close the door.
Theft
Vehicle theft is big business, especially in some cities,
and even commercial vehicles are no exception. Although
your vehicle has a number of theft
-deterrent features, we
know that nothing we put on it can make it impossible to
steal. However, there are ways you can help.
Key in the Ignition
If you leave your vehicle with the keys inside, it's an
easy target for joy riders or professional thieves
-- so
don't do it.
Remember to remove your key and take it with you.
Always do this. When you take your key with you, your
ignition will be locked. Also remember to lock the doors.
New Vehicle ªBreak-Inº
NOTICE:
Your vehicle doesn't need an elaborate
ªbreak
-in.º But it will perform better in the long
run if you follow these guidelines:

Let your engine warm up before you
operate your vehicle under load.

Keep your speed at 55 mph (88 km/h) or
less for the first 500 miles (805 km).

Don't drive at any one speed
-- fast or
slow
-- for the first 500 miles (805 km).
Don't make full
-throttle starts.

Avoid making hard stops for the first
200 miles (322 km) or so. During this time
your new brake linings aren't yet broken
in. Hard stops with new linings can mean
premature wear and earlier replacement.
Follow this breaking
-in guideline every
time you get new brake linings.
NOTICE: (Continued)
ProCarManuals.com

yellowblue
2-8 Manual Transmission
Set the parking brake, shift your gear selector to
NEUTRAL and hold the clutch pedal to the floor while
starting the engine.
Starter Motor Operation
1. The starter motor will disengage if you release
the key or the engine reaches a predetermined
engine speed.
2. To prevent overheating, the starter motor will
disengage after continuously operating for 15 seconds.
You must release the key from the start position to
re
-engage the starter.
3. The starter motor will not engage if the engine is
already running.
4. The starter motor will disengage if, after two
seconds, the starter pinion gear does not engage the
flywheel or there is no engine rpm signal from the
engine speed sensor.
Starting Your Engine
1. Without pushing the accelerator pedal, turn your
ignition key to START. When the engine starts, let
go of the key. The idle speed will go down as your
engine gets warm.
2. If the engine doesn't start in 10 seconds, push the
accelerator pedal all the way down and crank the
engine for five more seconds, unless it starts sooner.
3. If your engine still won't start (or starts but then
stops), it could be flooded with too much gasoline.
Wait 15 seconds to let the starter motor cool down.
Do Steps 1 through 3 again.
When the engine starts, let go of the key and the
accelerator pedal.
ProCarManuals.com

yellowblue
2-9
NOTICE:
Your engine is designed to work with the
electronics in your vehicle. If you add electrical
parts or accessories, you could change the way
the engine operates. Before adding electrical
equipment, check with your dealer. If you don't,
your engine might not perform properly.
If you ever have to have your vehicle towed, see
the part of this manual that tells how to do it
without damaging your vehicle. See ªTowing
Your Vehicleº in the Index.
Gasoline Engine Warm-Up
When you've started your engine, let it run for 20 or
30 seconds to warm up before you put a load on
the engine.
Drive at moderate speeds for the first few miles,
especially in cold weather. Running a cold engine at
high speed can damage it.
Restarting the Gasoline Engine While
Moving (Automatic Transmission)
If you have to restart the engine while the vehicle is
moving, you'll first have to shift the automatic
transmission to NEUTRAL (N). This safety feature
prevents starting the engine when the transmission is in
a drive gear.
Stopping the Gasoline Engine
Let your engine idle for a few seconds before turning it
off after you have finished driving your vehicle.
If you shift to NEUTRAL (N), set the parking brake.
If you shift to PARK (P), the auto
-apply feature will set
the parking brake.
If your vehicle has a two
-speed axle, put the range
selector in LOW. To be sure the axle has shifted into
LOW, engage the clutch and transmission the vehicle
may move slightly when you do this.
While your engine is idling before you turn it off, you
can make a list of any operational or handling concerns
to give to responsible maintenance personnel so they can
handle them right away.
Moisture will condense in a fuel tank that is almost
empty if the vehicle is not run for a while, even just
overnight under some conditions. So, it's always best to
refuel your vehicle at the end of each run.
ProCarManuals.com

yellowblue
2-10
Starting Your Diesel Engine
If you have a Caterpillar diesel engine, also refer to
your Caterpillar
Operation & Maintenance Manual for
starting procedure.
To make starting easier in cold weather (below 32F or
0C), the proper viscosity engine oil should be used. It's
also best to heat the engine oil first. You can do this by
using an engine coolant heater. A GM Automatic Ether
Injection System aids cold weather starting.
NOTICE:
Your diesel engine has an electric air intake
heater system which reduces white smoke and
helps start the engine in cold weather. Do not
spray starting fluid into the air intake where it
can contact the heater elements.
If you don't have the GM Automatic Ether
Injection System, don't use starting fluid or
you could damage your engine. If you have the
GM system, use only GM approved starting fluid
that has been tested to establish compatibility
with the air inlet heater system.
NOTICE:
If you ever have to have your vehicle towed, see
the part of this manual that tells how to do it
without damaging your vehicle. See ªTowing
Your Vehicleº in the Index.
Restarting the Diesel Engine While Moving
(Automatic Transmission)
If you have to restart the engine while the vehicle is
moving, you'll first have to shift the automatic transmission
to NEUTRAL (N). This safety feature prevents starting
the engine when the transmission is in a drive gear.
Stopping the Diesel Engine
If you have a Caterpillar diesel engine, see your
Caterpillar
Operation & Maintenance Manual.
1. Set the parking brake and shift to NEUTRAL (N) or
PARK (P).
2. Turn the ignition switch key to OFF.
If your vehicle has a two
-speed axle, see ªRear Axle,
Tw o
-Speed Electric Shift Controlº or ªRear Axle,
Tw o
-Speed Airshift Controlº in the Index.
ProCarManuals.com

yellowblue
2-13
The manual fast idle feature is activated by pressing the
switch on the instrument panel. When the switch is
pressed again, or any of the previous conditions are not
met, manual fast idle will be deactivated.
Manual fast idle can be used to set any desired idle
speed. To set a new temporary engine idle speed:
1. Make sure all of the previously described conditions
are met.
2. Press the accelerator pedal to the desired engine speed.
3. Momentarily press the manual FAST IDLE switch.
The temporary idle speed will be set. This new rpm
level will be remembered by the system until either the
ignition is turned to OFF or a new idle speed is set.
Radiator Shutters -- Caterpillar

(If Equipped)
Radiator shutters aid engine warm-up by blocking the
airflow through the radiator and charge the air cooler to
conserve heat in cold conditions.
The radiator shutters on your vehicle (if equipped)
operate automatically. When the ignition switch is in
RUN or START and the engine temperature is below
195F (90C), the shutters will close, blocking the flow
of air through the radiator and charge the air cooler.When the engine temperature reaches 195F (90C), the
shutters will open to the normal operating position.
Engine Checks Before Operating
When you've started your engine, let it run for 20 to
30 seconds before you put a load on the engine.
But don't leave the vehicle while the engine is running.
During this warm
-up period, check your warning lights
and gages:

If oil pressure doesn't begin to rise within 15 seconds
of starting, stop the engine and find the cause.

If the engine coolant temperature gage needle goes
into the hot area on the gage, stop the engine and
find the cause of the overheating.

If you have air brakes, the dual
-needle air pressure
gage should read at least 105 psi (720 kPa) for both
service systems before you try to move the vehicle.
When air pressure is below 60 psi (420 kPa), the
LOW AIR light will come on and you will hear a
tone alarm. If the pressure doesn't build up or drops
during warm
-up, stop the engine and find the cause
before you try to move the vehicle. Recommended
air pressure before actually driving away is
120 psi (830 kPa).
ProCarManuals.com

yellowblue
2-28
CAUTION:
If you apply any one of the air brake parking
controls while the vehicle is moving, your rig will
stop suddenly. If you are not ready for this, you
or others could be injured. Don't apply any one
of these controls while you're driving, unless you
have to make an emergency stop.
If the air pressure drops below 60 to 70 psi (413 to
482 kPa), the PRIMARY BRAKE light will come on. If
the air pressure drops to 40 to 45 psi (275 to 309 kPa), the
yellow knob will automatically pop out and apply the
spring brakes. If you ever have a complete loss of air so
that your air brakes automatically apply, there is a way that
the tow operator can release the parking brakes to tow the
vehicle. See ªTowing Your Vehicleº in the Index.
CAUTION:
If your vehicle is left in gear, the engine can
start if the vehicle starts to roll. This can easily
happen if you have the diesel engine. Shift the
transmission into NEUTRAL (N) before you
leave the vehicle.
ProCarManuals.com

yellowblue
2-34
An arrow on the instrument panel will flash in the
direction of the turn when the lever is in the up or
down position.
This system replaces the turn signal feature of the
multifunction lever only. All other features such as
headlamp high/low beam, windshield wipers and
washer, etc. remain part of the multifunction system.
If you have this system, see ªSignal
-Stat Turn Signal
and Hazard Warning Flasherº in the Index to find out
how the hazard warning flasher portion works.
Headlamp High/Low Beam Changer
To change the headlamps from low beam to high, push
the multifunction lever away from you. To switch back
to low beam, pull the lever toward you.
When the high beams are
on, a light on the instrument
cluster will also be on.
Windshield Wipers
The windshield wipers are controlled by turning the
band with the wiper symbol on it.
For a single wiping cycle, turn the band to MIST. Hold
it there until the wipers start, then let go. The wipers will
stop after one cycle. If you want more cycles, hold the
band on MIST longer.
For steady wiping at low speed, turn the band away
from you to the LO position. For fast wiping, turn the
band to HI. To stop the wipers, turn the band to the
off symbol.
ProCarManuals.com

yellowblue
2-58
Hydraulic Brake System Warning Lights
Vehicles with hydraulic systems have two brake system
warning lights on the instrument panel.
If the PRIMARY BRAKE
warning light comes on, it
means that the fluid level in
the master cylinder
reservoir is low or there is
another problem with your
primary hydraulic brakes.
When it comes on, you will also hear a warning tone.
The PRIMARY BRAKE warning light may come on,
and the warning tone may sound, when you're turning
and braking at the same time. This is normal. See
ªHydraulic Brake Systemsº in the Index.
If the AUX BRAKE
warning light comes on, it
means that there is
something wrong in the
auxiliary brake system.
When this light comes on, you will also hear a warning tone.Both of these lights should come on briefly every time
you start the engine. If they don't come on then, have
them fixed so they will be ready to warn you if there's a
problem. If one or both of these warning lights stay on
after you start the engine, there could be a brake
problem. Have your brake system inspected right away.
If one or both of these lights come on and stay on while
you are driving, pull off the road and stop carefully. You
may notice that the pedal is harder to push. Or, the pedal
may go closer to the floor. It may take longer to stop.
If either light is still on, have the vehicle towed for
service. (See ªTowing Your Vehicleº in the Index.)
See ªHydraulic Brake Systemsº in the Index for
more information.
CAUTION:
Your brake system may not be working properly
if a brake system warning light is on. Driving
with either of the brake system warning lights on
can lead to an accident. If either light is still on
after you've pulled off the road and stopped
carefully, have the vehicle towed for service.
ProCarManuals.com

yellowblue
2-59
Air Brake System Warning Light
Vehicles with air brake systems have one brake system
warning light on the instrument panel.
The LOW AIR warning
light should come on, as a
check, whenever you start
the engine.
However, it is designed to come on, and stay on, when
brake reservoir pressure has dropped below 60 to 70 psi
(410 to 480 kPa).When this warning light comes on, you will also hear a
warning tone. If the warning light and tone come on
while you are driving, you should drive only as far as
the nearest point of safety and then stop the vehicle.
Here's a very important thing for you to know:
CAUTION:
If the LOW AIR warning light comes on and the
warning tone sounds, the vehicle can stop
suddenly and without further warning. This is
because the parking brake will come on if the
pressure falls below 40 to 45 psi (275 to 310 kPa).
You or others could be injured. If the LOW AIR
warning light comes on and the warning tone
sounds, stop as soon as you can. You won't
know how quickly the system is losing pressure,
so be aware that the parking brake may come
on suddenly.
ProCarManuals.com