recommended oil GMC C-SERIES 1999 Owners Manual

yellowblue
2-13
The manual fast idle feature is activated by pressing the
switch on the instrument panel. When the switch is
pressed again, or any of the previous conditions are not
met, manual fast idle will be deactivated.
Manual fast idle can be used to set any desired idle
speed. To set a new temporary engine idle speed:
1. Make sure all of the previously described conditions
are met.
2. Press the accelerator pedal to the desired engine speed.
3. Momentarily press the manual FAST IDLE switch.
The temporary idle speed will be set. This new rpm
level will be remembered by the system until either the
ignition is turned to OFF or a new idle speed is set.
Radiator Shutters -- Caterpillar

(If Equipped)
Radiator shutters aid engine warm-up by blocking the
airflow through the radiator and charge the air cooler to
conserve heat in cold conditions.
The radiator shutters on your vehicle (if equipped)
operate automatically. When the ignition switch is in
RUN or START and the engine temperature is below
195F (90C), the shutters will close, blocking the flow
of air through the radiator and charge the air cooler.When the engine temperature reaches 195F (90C), the
shutters will open to the normal operating position.
Engine Checks Before Operating
When you've started your engine, let it run for 20 to
30 seconds before you put a load on the engine.
But don't leave the vehicle while the engine is running.
During this warm
-up period, check your warning lights
and gages:

If oil pressure doesn't begin to rise within 15 seconds
of starting, stop the engine and find the cause.

If the engine coolant temperature gage needle goes
into the hot area on the gage, stop the engine and
find the cause of the overheating.

If you have air brakes, the dual
-needle air pressure
gage should read at least 105 psi (720 kPa) for both
service systems before you try to move the vehicle.
When air pressure is below 60 psi (420 kPa), the
LOW AIR light will come on and you will hear a
tone alarm. If the pressure doesn't build up or drops
during warm
-up, stop the engine and find the cause
before you try to move the vehicle. Recommended
air pressure before actually driving away is
120 psi (830 kPa).
ProCarManuals.com

yellowblue
5-23
CAUTION:
Adding only plain water to your cooling system
can be dangerous. Plain water, or some other
liquid like alcohol, can boil before the proper
coolant mixture will. Your vehicle's coolant
warning system is set for the proper coolant
mixture. With plain water or the wrong mixture,
your engine could get too hot but you wouldn't
get the overheat warning. Your engine could
catch fire and you or others could be burned.
Use a 50/50 mixture of clean, drinkable water
and DEX
-COOL
coolant.
NOTICE:
In cold weather, water can freeze and crack the
engine, radiator, heater core and other parts.
Use the recommended coolant and the proper
coolant mixture.
Specialty Hood Sloped Hood
CAUTION:
You can be burned if you spill coolant on hot
engine parts. Coolant contains ethylene glycol
and it will burn if the engine parts are hot
enough. Don't spill coolant on a hot engine.
ProCarManuals.com

yellowblue
5-30
CAUTION:
Adding only plain water to your cooling system
can be dangerous. Plain water, or some other
liquid like alcohol, can boil before the proper
coolant mixture will. Your vehicle's coolant
warning system is set for the proper coolant
mixture. With plain water or the wrong mixture,
your engine could get too hot but you wouldn't
get the overheat warning. Your engine could
catch fire and you or others could be burned.
Use a 50/50 mixture of clean, drinkable water
and coolant.
NOTICE:
In cold weather, water can freeze and crack the
engine, radiator, heater core and other parts. So
use the recommended coolant.
CAUTION:
You can be burned if you spill coolant on hot
engine parts. Coolant contains ethylene glycol
and it will burn if the engine parts are hot
enough. Don't spill coolant on a hot engine.
ProCarManuals.com

yellowblue
6-6
NOTICE:
If there is water in your diesel fuel and the
weather is warm or humid, fungus and bacteria
can grow in the fuel. They can damage your fuel
system. You'll need a diesel fuel biocide to
sterilize your fuel system. Your dealer can advise
you if you ever need this.
If your fuel tank needs to be purged to remove
water, see your dealer or a qualified technician.
Improper purging can damage your fuel system.
Diesel engine vehicles that stand unused for several
days or weeks can develop water in the fuel from
condensation. It helps to fill the fuel tank if the
diesel engine vehicle will not be used for a time.
Fuels in Foreign Countries
(Gasoline Engines)
If you plan on driving in another country outside the
United States or Canada, the proper fuel may be hard to
find. Never use leaded gasoline or any other fuel not
recommended in the previous text on fuel. Costly repairs
caused by use of improper fuel wouldn't be covered by
your warranty.
To check on fuel availability, ask an auto club, or
contact a major oil company that does business in the
country where you'll be driving.
You can also write us at the following address for
advice. Just tell us where you're going and give your
Vehicle Identification Number (VIN).
General Motors Overseas Distribution Corporation
1908 Colonel Sam Drive
Oshawa, Ontario L1H 8P7
ProCarManuals.com

yellowblue
6-14 When to Add Engine Oil
If the oil is at or below the cross-hatched area, then
you'll need to add at least one quart of oil. But you must
use the right kind. This part explains what kind of oil to
use. For crankcase capacity, see ªCapacities and
Specificationsº in the Index.
NOTICE:
Don't add too much oil. If your engine has so
much oil that the oil level gets above the
cross
-hatched area that shows the proper
operating range, your engine could be damaged.
Be sure to fill it enough to put the level somewhere in
the proper operating range. Push the dipstick all the way
back in when you're through.
What Kind of Engine Oil to Use
Oils recommended for your vehicle can be identified by
looking for the ªStarburstº symbol. This symbol
indicates that the oil has been certified by the American
Petroleum Institute (API). Do not use any oil which
does not carry this Starburst symbol.
If you change your own oil,
be sure you use oil that has
the Starburst symbol on the
front of the oil container. If
you have your oil changed
for you, be sure the oil put
into your engine is
American Petroleum
Institute certified for
gasoline engines.
You should also use the proper viscosity oil for your
vehicle, as shown in the following chart:
ProCarManuals.com

yellowblue
6-15
As shown in the chart, SAE 5W-30 is best for your
vehicle. However, you can use SAE 10W
-30 if it's going
to be 0F (
-18C) or above. These numbers on an oil
container show its viscosity, or thickness. Do not use
other viscosity oils, such as SAE 20W
-50.
NOTICE:
Use only engine oil with the American Petroleum
Institute Certified For Gasoline Engines
ªStarburstº symbol. Failure to use the
recommended oil can result in engine damage
not covered by your warranty.
GM Goodwrench
oil meets all the requirements for
your vehicle.
If you are in an area where the temperature falls below
-20F (-29C), consider using either an SAE 5W-30
synthetic oil or an SAE 0W
-30 oil. Both will provide
easier cold starting and better protection for your engine
at extremely low temperatures.
ProCarManuals.com

yellowblue
6-20
Rear Axle
When to Check and Change Lubricant
Refer to the Maintenance Schedule to determine how
often to check the lubricant and when to change it.
See ªScheduled Maintenance Servicesº in the
Maintenance Schedule.
How to Check Lubricant
If the level is below the bottom of the filler plug hole,
you'll need to add some lubricant. Add enough lubricant
to raise the level to the bottom of the filler plug hole.
What to Use
Refer to the Maintenance Schedule to determine what
kind of lubricant to use. See ªRecommended Fluids and
Lubricantsº in the Maintenance Schedule.
Rear Axle Shift Motor (Option)
When to Check and Change Fluid
If you have an optional air-shift two-speed, controlled
traction, or locking differential type rear axle, a good
time to check the fluid level in the axle shift motor is
when the rear axle lubricant is checked. Use refrigerant
oil (shift motor only).
How to Check Fluid
Remove the plug on the front plate of the axle shift
motor, add enough fluid to raise the level to the bottom
of the filler plug hole, then replace the plug.
What to Use
Refer to your Maintenance Schedule to determine what
kind of lubricant to use.
ProCarManuals.com

yellowblue
6-44
Other Service Items
Component Box
Your vehicle has a component box along the left frame rail.
What is in the box depends on what options are on your
vehicle. Normally, the fuel filter, air dryer, Luberfiner oil
filter, emission canister or other components are in there.
To get into the box, you first have to remove the top
cover. To do that, remove the two 8 mm bolts on top and
the single 8 mm bolt at the top front. Then, pull the
cover toward you and lift it off.You can then remove the front cover if you need to, by
removing the two 8 mm bolts and pulling it off.
When you're through, be sure to put the front cover on,
before you put on the top cover.
Fuel Filter (Gasoline Engines)
The steel fuel filter is located inside the component box
at the rear. See your Maintenance Schedule for
recommended service intervals.
If your vehicle is equipped with the optional Davco
spin
-on type filter, it is also located in the component box.
ProCarManuals.com

yellowblue
6-45 Fuel Filter (Diesel Engines)
The ACDelco
fuel filter is located in the component
box. See your Maintenance Schedule for recommended
service intervals.
Primary Fuel Filter and Water Separator
(Option)
If you have a Caterpillar

diesel engine, you may
have this spin
-on filter.
It is in the component box
on the driver's side behind
the fender.
It has a clear plastic drain bowl at the bottom. Check the
drain bowl occasionally for any water or particles. To
drain the bowl, shut off the engine. Then partially open
the drain valve at the bottom of the filter. See ªEngine
Oilº in the Index for proper disposal procedures.
Secondary Fuel Filter and Water
Separator/Heater (Option)
If you have a Caterpillar

diesel engine, you may have
this spin
-on filter and fuel
separator/heater. It is
mounted on the passenger's
side of the engine.
It has a metal drain bowl at the bottom. Occasionally, check
the bowl for any water or particles. To check or drain the
bowl, shut off the engine. Then push up on the spring loaded
drain valve until clear fuel is flowing from the valve. The
particles or water will drain out first. See ªEngine Oilº in the
Index for proper disposal procedures.
ProCarManuals.com

yellowblue
6-47 Front Wheel Bearings with Oil-Filled Hubs
If your vehicle has oil-filled
hubs, occasionally check to
see if they have enough oil.
You can tell by looking into
the sight glass to see if there
is oil there.
If there isn't, clean the rubber fill plug in the center of
the glass, and then remove it. Be careful not to allow
any dirt or water to get into the oil. Add enough of the
recommended oil to bring it up to the level mark that
you'll see on the glass.
Refer to your Maintenance Schedule for the proper oil
to use.
When you fill the hub, check the glass again after
driving a short distance. It takes a while for the oil to
flow through the system, and you may find that you
have to add a little more to fill it to the proper level.
Air Conditioning System
Every now and then, have your dealership check your
air conditioning system to be sure it has not lost any
cooling ability. If you think the system is not working
properly, have your GM Truck dealer check it out as
soon as possible.
The air conditioning won't work when the temperature
outside is below 40
F (4
C).
NOTICE:
If your vehicle is equipped with factory air
conditioning, the system is charged with the
R
-134a refrigerant. Servicing of the air
conditioning system should be performed by a
trained service technician.
ProCarManuals.com