lock GMC JIMMY 1997 Owner's Guide

4LO: This setting also engages your front axle to give
you extra traction. You may never need 4LO. It sends
the maximum power to all
four wheels. You might
choose 4LO
if you were driving off-road in sand, mud
or deep snow and climbing or descending steep hills.
Indicator lights
in the switches show you which setting
you are
in. The indicator lights will come on briefly when
you turn on
the ignition and one will stay on. If the lights
do not come
on, you should take your vehicle in for
service.
An indicator light will flash while shifting. It will
remain illuminated when the shift is completed.
Shifting from 2HI to 4HI
Press and release the 4HI switch. This can be done at
any speed. and the front axle will lock automatically.
Shifting from 4HI to 2HI
Press and release the 2HI switch. This can be done at
any speed. and the. front axle will unlock automatically.
Shifting from 2HI or 4HI to 4LO
To
shift from 2HI or .CHI to 4LO. the vehicle must be
stopped or moving less than
3 rnph (4.8 k~nh) with the
transmission
in NEUTRAL (N) in vehicles equipped with an
automatic transmission or the clutch pedal engaged
in
vehicles equipped with a manual transmission. The
preferred method for shifting into 4LO is to have your
vehicle moving
1 to 2 mph (I .6 to 3.2 kmh). Press
and release
the 4LO switch. You must wait for the
4LO indicator light to stop flashing and remain
illuminated before shifting your transmission into
gear or releasing
the clutch pedal.
If the 4L0 switch is pressed when your vehicle is
in
gear and/or moving, the 4LO indicator light will flash
for
30 seconds and not complete the shift unless your
vehicle is moving slower than
3 tnph (4.8 km/h) and
the transmission
is in NEUTRAL (N) or the clutch
pedal engaged.
On automatic transmission equipped vehicles,
if your
transfer case does
not shift into 4LO. your transmission
indicator switch may reyuire adjustment. With
your
transmission in NEUTRAL (N)! press and release the
4L0 switch. While the 4LO indicator light is flashing.
shift yo~lr transmission into PARK (P). Wait unlil the
4L0 indicator light remains illuminated before shifting
your trrmstnission
into gear. This will get you into 4LO.
but you should take
your vehicle in for service to restore
normal operation.

0 Move the lever up as far as it will go.
3. If you have four-wheel drive with a manual transfer
case shift lever-. be sure the transfer case is in a drive
gear
-- not in NEUTRAL (N).
4. Turn the ignition key to LOCK.
5. Retnove the key and take it with you. If you can
leave your vehicle with the key, your vehicle is in
PARK (P).
Console Shift Lever
1. Hold the brake pedal down with your right foot and
set the parking brake.
2. Move the shift lever into PARK (P) position like this:
0 Hold in the button on the lever.
0 Push the lever all the way toward the front of
the vehicle.
3. Turn the ignition key to LOCK.
4. Remove the key and take it with you. If you can leave
your vehicle with the key. your vehicle
is in PARK (P).
2-31

Leaving Your Vehicle With the Engine
Running (Automatic Transmission
Models Only)
It can be dangerous to leave your vehicle with the
engine running. Your vehicle could move suddenlJ
if the shift lever
is not fully in PARK (P) with the
parking brake firmly set. If you have four-wheel
drive with
a manual transfer case shift lever and
your transfer case
is in NEUTRAL (N), your
vehicle will
be free to roll, even if your shift lever
is in
PARK (P). So be sure the transfer case is in a
drive gear
-- not in NEUTRAL (N). And, if you
leave the vehicle with the engine running, it could
overheat and even catch fire. You or others could
be injured. Don't leave
your vehicle with the
engine running unless you have to.
If you have to leave your vehicle with the engine
running, be sure your vehicle
is in PARK (P) and yo~~r parking brake
is firmly set before you leave
it. After
you've moved the shift lever into the PARK
(P)
position, hold the regular brake pedal down. Then, see
if you can move the shift lever away from PARK (P)
without first pulling it toward you (or pressing the
button on
a console shift lever). If YOLI can, it means that
the shift lever wasn't fully locked
into PARK (P).
Torque Lock (Automatic Transmission)
If you are parking on a hill and you don't shift your
transmission into PARK
(P) properly, the weight of the
vehicle may put too much force
on the parking pawl in the
transmission. You may find it difficult to pull the shift
lever out
of PARK (P). This is called "torque lock." To
prevent torque lock, set the parking br'ke and then shift
into PARK
(P) properly before you leave the driver's seat.
To find out how, see "Shifting Into PARK (P)" in
the Index.
When
you are ready to drive, move the shift lever out of
PARK (P) kc$~w you release the parking brake.
IF torque lock does occur. you may need to have another
vehicle push yours
a little uphill to take some of the
pressure from
the parking pawl in the transmission, so
~OLI can pull the shift lever out of PARK (P).
2-32

Shifting Out of PARK (P)
(Automatic Transmission)
Your vehicle has a brake-transmission shift interlock.
YOLI have to fully apply your regular brake before you
can shift
from PARK (PI when the ignition is in the
RUN position. See "Automatic Transmission Operation"
in the Index.
If you cannot shift out of PARK (P)? ease pressure on
the shift lever
-- push the shift lever all the way into
PARK (P) as you maintain brake application. Then
move the shift lever into the gear you want (you must
press the shift lever button
if you have the console
shift lever).
If you ever hold the brake pedal down but still can't
shift out
of PARK (P)? try this:
1. Turn the key to OFF.
2. Apply and hold the brake until the end of Step 3.
3. Shift to NEUTRAL (N).
4. Start the vehicle and then shift to the drive gear
you want.
5. Have the vehicle fixed as soon as you can.
Parking Your Vehicle (Manual
Transmission Models Only)
Before you get out of your vehicle, turn off your engine,
put your- manual transmission in REVERSE (R) and
firmly apply the parking brake.
If you have four-wheel drive with it manual transfer case
shift lever, be sure your transfer case is in a drive gear.
Your vehicle could roll
if it isn't.
If you are parking on a hill. or if your vehicle is pulling
a trailer, see "Towing a Trailer" in the Index.
2-33

Lockout Switch
Four-door vehicles have a lockout feature to prevent
passengers from operating power
windows. It is located
on the driver’s door. Press LOCK to activate this feature.
Press
NORM and the windows return to normal operation.
Swing-Out Windows (2-Door Only)
If your vehicle has rear
swing-out windows, unlatch
them
at their clasps and
push out
on the glass to
open them.
When you close the window, be sure the latch catches.
Horn
TO sound the horn, press the horn symbols on the
steering wheel pad.
2-37

Tilt Wheel (If Equipped)
If you have the tilt steering
wheel,
you should adjust
the steering wheel before
you drive.
You can raise it to the highest level to give your legs
more
room when you enter and exit the vehicle.
To tilt the wheel, hold the steerins wheel and pull the
lever toward you. Move the steering wheel
to a
comfortable level. then release the lever to lock the
wheel in place.
Do not ad-just the steering wheel while driving.
Turn Signal/Multifunction Lever
The lever on the left. side of the steering column
includes your:
Turn Signal and Lane Change Indicator
Headlamp HighLow Beam Changer
0 Windshield Wipers
0 Windshield Washer
2-38 -

Windshield Wipers
You control the windshield
wipers
by turning the band
with the wiper symbol
on it.
For a single wiping cycle. turn the band to MIST. Hold
it there until the wipers start. then let go. The wipers will
stop after one wipe. If you want Inore wipes, hold the
band on
MIST longer.
You can set the wiper speed I‘or a long or short delay
between wipes. This can be very
LIS~~LII in light rain or
snow. Turn the band to choose the delay time. The
closer to
LOW, the shorter the delay.
Be sure to ciear ice and snow from the wiper blades
before using them. If they’re frozen to the windshield,
carefully loosen or thaw them.
If your blades do become
worn or datnaged.
set new blades or blade inserts.
Windshield Washer
At the top of the multifunction lever there’s a paddle
marked with the windshield washer
symbol and PUSH.
To spray washer fluid on the windshield, press the
paddle. The wipers
will clear the window and then
either stop or return to your preset speed.
I
I
A C iTJTION:
In freezing weather, don’t use your washer until
the windshield is warmed. Otherwise the washer
fluid can
form ice an the windshield, blocking
your vision.
2-40

Lamps On Reminder
A reminder tone will sound when your headlamps or
parking lamps are turned
on and your ignition is in OFF,
LOCK or ACCESSORY. To turn the tone off, press the
OFF switch.
Daytime Running Lamps
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the day.
DRL can be helpful in many different driving
conditions, but
they can be especially helpful in the
short periods after dawn and before sunset.
The DRL system will make your headlamps come on at
reduced brightness when:
the ignition is on,
the headlamp switch is off and
the parking brake is released. When
the DRL are
on. only your headlamps will be on.
The taillamps, sidemarker and other lamps won't be on.
The instrument panel won't be
lit up either.
When
it begins to get dark, your DRL indicator light is a
reminder to turn your headlamp switch on. The other
lamps that come on
with your headlamps will also
come on.
When you
turn the headlamp switch off, the regular
lamps will
go off, and your headlamps will change to
the reduced brightness
of DRL.
To idle your vehicle with the DRL off, set the parking
brake. The DRL
will stay off until you release the
parking brake.
As with any vehicle, you should turn on the regular
headlamp system when you need it.
2-46

Front Map Lamps (If Equipped)
If your vehicle has optional front rmp lamps, they
are located on the inside rearview mirror. They
will
automatically come on for approximately 20 seconds
when either front door is opened or unlocked with
the
Keyless Entry System, if so equipped, or until the
ignition key is turned to RUN or ACCESSORY. The
lamps
will also stay on for approxinlately 15 seconds
after you exit the vehicle.
They
will also stay on for I5 seconds when the INT
LIGHTS switch on the instrument panel is turned on
then off, while the ignition is off.
You can also turn the lamps on and off by pressing the
switch near each lamp.
Dome Lamps
The rear dome lamp has a switch that lets you turn it on
from the rear of the vehicle.
Press the side
of the switch with the lamp symbol to turn
on the front and rear dome lamps. Pressing the other side
of the swirch
will turn the cargo area dome lamp off,
even when the endgate or liftgate and doors are open.
2-48

I NOTICE:
Don’t put papers and other things that burn into
your ashtray.
If you do, cigarettes or other
smoking materials could set them on
fire
causing damage.
To remove the front ashtray, lift the release tab as high
as possible, then remove the tray.
Four-door vehicles have smaller ashtrays inside the rear
doors. Press
PUSH to turn the ashtray around for use.
Sun Visors
To block out glare, you can swing down the top and
bottom visors.
You can also swing the bottom visor from
side to side. Your visors may have
an extension that can
be pulled out for additional glare protection
and a strap
for holding small items, such as
maps.
Visor Vanity Mirror
Pull the sun visor down and lift the cover to expose the
vanity mirror.
Illuminated Visor Vanity Mirror
(If Equipped)
Pull the sun visor down and lift the mirror cover to turn
on the lamps.
2-62