change time GMC SIERRA 1993 Owner's Manual

Service & Appearance Cam
Tire lnspecfion and Rotation
To make your tires last longer, have them inspected and rotated at the
mileages recommended in the Maintenance Schedule. See “Scheduled
Maintenance Services” in the Index.
Q
-
-
K2655
Use this rotation pattern.
If your vehicle has front tires with different load ratings or tread designs (such
as all season
vs. onloff road) than the rear tires, don’t rotate your tires \
front
to rear.
After the tires have been rotated, adjust the front and rear \
inflation pressure
as shown on the CertificationRire label. Make certain that all wheel nuts are
properly tightened. See “Wheel Nut Torque”
in the Index.
A Rust or dirt on a wheel, or on the parts to which -it is fastened, can
make the wheel nuts become loose after a time. The wh.eel could
come
off and cause an accident. When you change- a- :wheel, remove
’ any -rust or dirt from places where the wheel attaches to the vehicle:
,: In an emergency, you can use a cloth or paper towel to do this; but
3 be sure to use a scraper or wire brush later, if you need- to, to get
-T all the rust or dirf off. See “Changing a Flat Tire” in the Index.
6-78
ProCarManuals.com

Specification Charts
Replacement Parts
Replacement part numbers listed in this section are based on the latest
information available at the time of printing, and are subject \
to change. If a
part listed in this manual is not the same as the part used \
in your vehicle
when it was built, or
if you have any questions, please contact your GM truck
dealer.
Engine Identification
Liter Produced Fuel VIN
Displacement Type
U.S. TBI N
V8 7.4 H.D.
us. Diesel F V8 6.5
H.D. U.S. Diesel J V8 6.2
L. D. us. Diesel C V8 6.2
US., Can.
TBI K V8
5.7
L. D. US., Can.
TBI H
V8 5.0
U.S. TBI 2 V6
4.3
Emissions
BY
System
Engine Code
*
*
*
*Light Duty Emissions with 8500 GVWR and below or:
Heavy Duty Emissions with 8501 GVWR and above.
TO035
Wheel Nut Torque
MODEL I DESCRIPTION I TORQUE I
C 1500 5 bolts (14mm) 120 ft. Ibs. (160 Nmm)
K 1500 & C-K 2500 6 bolts f14mm) 120 ft. Ibs. (1 60 N.m)
C-K
2500 (w/C6P) 8 bolts (14mm) 120 ft. Ibs. (160 Nmm)
C-K 3500 Single Rear Wheels 8 bolts (14mm) 120
ft. Ibs.
(1 60 N-m)
C3500 Dual Rear Wheels
8 bolts (14mm) 140 ft. Ibs. (190
N-m)
C3500 HD -Front
5 bolts (5/8 in.) 175 ft. Ibs. (240 Nsm)
TO040
--Rear
10 bolts (5/8 in.)
6-95
ProCarManuals.com

Scheduled Maintenance Services
Explanation Of Scheduled Maintenance Services
Below are explanations of the services listed in the maintenance charts.
The proper fluids and lubricants to use are listed in this section. Make sure
whoever services your vehicle uses these. All parts should be \
replaced and
all necessary repairs done before you or anyone else drives the ve\
hicle.
1.
ENGINE OIL AND OIL FILTER CHANGE* -ALWAYS USE SG OR
SGKE QUALITY, ENERGY CONSERVING II OILS OF THE PROPER
VISCOSITY. To determine the preferred viscosity oil for your vehicle’s
engine (e.g. SAE 5W-30 or 10W-30), see “Engine Oil” in the Index.
2. CHASSIS LUBRICATION -Lubricate the front suspension, king pin
bushings, steering linkage, transmission, and transfer case shift\
linkage,
parking brake cable guides, propshaft splines (2 wheel drive), brake
pedal springs, and clutch pedal springs at the intervals specified.
If you have a 3500 HD, lubricate the king pins and king pin bushings
every 1,500 miles
(2500 km) for Maintenance Schedule 1, or every 3,000
(5000 km) for Maintenance Schedule 2.
Ball joints and king pin bushings should not be lubricated unless their
temperature is
10°F (-12”C), or higher. When the weather is cold, let
them warm up before lubrication or they could be damaged.
Also, be sure to check
all the vehicle fluid levels at this time.
3.
CLUTCH FORK BALL STUD LUBRICATION -Lubricate the clutch fork
ball stud through the fitting on the clutch housing. Lubricant must be
added “sparingly” to the fitting, as only.
0066 Ib. (.003 kg) is required to
lubricate the ball stud surface.
Do not add lubricant more often than the
intervals in the Maintenance Charts.
Too much lubricant will damage
the clutch assembly.
4. ENGINE IDLE SPEED ADJUSTMENT (DIESEL ENGINES)* -Adjust to
the specifications shown on the underhood label. You must use
calibrated test equipment.
5. COOLING SYSTEM SERVICE* -Drain, flush and refill system with new
coolant. See “Engine Coolant’’ in the Index for the proper coolant and
mixture to use in your vehicle.
Also inspect the hoses and replace them
if they are cracked, swollen, or
deteriorated. Tighten all hose clamps (except constant tension \
clamps).
Remove debris and clean the outside
of the radiator and air conditioning
condenser. Wash the radiator neck.
To ensure proper operation, pressure
test the radiator and cap.
* An Emission Control Service
7-1
8
ProCarManuals.com

When contacting GMC Truck, please remember that your concern wi\
ll likely be resolved in the dealership, using the dealership’s facilit\
ies, equipment and personnel. That is why we suggest you follow Step One first
if you have a
concern.
Customer Assistance for the Hearing or
Speech Impaired (TDD)
To assist owners who have hearing difficulties, GMC Truck has inst\
alled
special TDD (Telecommunications Devices for the Deaf) equipment\
at its
Customer Assistance Center. Any hearing or speech impaired custo\
mer who
has access to a TDD or conventional teletypewriter (TTY) can \
communicate
with GMC Truck by dialing:
In the United States
..................................................................... 1 -800-GMC-TKTD
In Canada
........................................................................\
................. 1-800-263-3830.
GM Participation in Better Business
Bureau Mediation/Arbitration Program*
*This program may not be available in all states, depending on\
state law.
Canadian owners refer to your Warranty and Owner Assistance Inf\
ormation
booklet.
General Motors reserves the right to change eligibility limitati\
ons and/or to
discontinue its participation in this program.
Our experience has shown that the Customer Satisfaction Procedur\
e
described earlier in this section has been very successful in \
achieving
customer satisfaction. However,
if you have not been substantially satisfied,
GMC Truck wants you to be aware of GM’s voluntary participa\
tion in a
no-charge mediationlarbitration program called BBB AUTO LINE. This program
is administered by the Council of Better Business Bureaus through local
Better Business Bureaus. The program can resolve individual disp\
utes
involving vehicle repairs and the interpretation of your New Vehicle Limited
Warranty.
We prefer that you not resort to BBB AUTO LINE until after a fi\
nal .decision
is made under the Customer Satisfaction Procedure. However, you \
may file a
claim at any time by contacting your local Better Business Bur\
eau (BBB) at
the following toll-free number: 1-800-955-5100. For further infor\
mation about
filing a claim, you may also write to: BBB AUTO
LINE, Council of Better
Business Bureaus, 4200 Wilson Boulevard, Suite 800, Arlington, V\
irginia
22203.
8-3
ProCarManuals.com