service GMC SIERRA 1993 Manual PDF
[x] Cancel search | Manufacturer: GMC, Model Year: 1993, Model line: SIERRA, Model: GMC SIERRA 1993Pages: 436, PDF Size: 23.88 MB
Page 359 of 436
r CAUTION I
If you operate your vehicle with a tire that is badly underinflated, the
tire can overheat. An overheated tire can lose air suddenly or catcl.
fire. You or others could be injured. Be sure all tires (including the
spare,
if any) are properly inflated.
Buying New Tires
To find out what kind and size of tires you need, look at the Certificationflire
label. The tires installed on your vehicle when it was new had a Tire
Performance Criteria Specification (TPC Spec) number on each tire’s sidewall.
When you get new tires, get ones with that same TPC Spec num\
ber. That
way, your vehicle will continue to have tires that are designed to give proper
endurance, handling, speed rating, traction, ride and other thin\
gs during
normal service on your vehicle. If your tires have an all-season tread design,
the TPC number will be followed by a
“MS” (for mud and snow).
If you ever replace your tires with those not having a TPC Spec number,
make sure they are the same size, load range, speed rating and construction
type (bias, bias-belted
or radial) as your original tires.
1 CAUTION
* Mixing tires could cause you to lose control while driving. If you mix
vehicle may not handle properly, and you could have a crash. Be
- ) tires of different sizes or types (radial and bias-belted tires), the
I sure to use the same size and type tires on all wheels. I
Uniform Tire Qua/ity Grading
The following information relates to the system developed by the United
States National Highway Traffic Safety Administration which grade\
s tires by
treadwear, traction and temperature performance. (This applies o\
nly to
vehicles sold in the United States.)
Treadwear
The treadwear grade is a comparative rating based on the wear rate of the
tire when tested under controlled conditions on a specified governmen\
t test
course. For example, a tire graded
150 would wear one and a half (1 1/2)
times as well on the government course as a tire graded 100. The relative
performance
of tires depends upon the actual conditions of their use,
however, and may depart significantly from the norm due to var\
iations in
driving habits, service practices and differences in road characteristics and
climate.
6-8 1
ProCarManuals.com
Page 360 of 436
Service & Appearance Care
Traction-A, B, C
The traction grades, from highest to lowest are: A, B, and C. They represent
the tire’s ability to stop on wet pavement as measured under controlled
conditions on specified government test surfaces of asphalt and concrete.
A
tire marked C may have poor traction performance.
Warning: The traction grade assigned to this tire is based on braking
(straight-ahead) traction tests and does not include cornering \
(turning) traction.
Temperature-A, B, C
The temperature grades are A (the highest), B, and C, representing the tire’s
resistance
to the generation of heat and its ability to dissipate heat when
tested under controlled conditions on a specified indoor laborat\
ory test wheel.
Sustained high temperature can cause the material of the tire to degenerate
and reduce tire life, and excessive temperature can lead to sudden tire
failure. The grade
C corresponds to a level ‘of performance which all
passenger car tires must meet under the Federal Motor Vehicle \
Safety
Standard
No. 109. Grades B and A represent higher levels of performance on
the laboratory test wheel than the minimum required by law.
Warning: The temperature grade for this tire is established for a tire that is
properly inflated and not overloaded. Excessive speed, underinfla\
tion, or
excessive loading, either separately or in combination, can caus\
e heat buildup
and possible tire failure.
These grades are molded on the sidewalls of passenger car tire\
s. While the tires available as standard or optional equipment on \
General Motors
vehicles may vary with respect to these grades, all such tires meet General
Motors performance standards and have been approved for use on \
General
Motors vehicles.
All passenger type (P Metric) tires must conform to Federal
safety requirements in addition to these grades.
Wheel AIignment and Tire Balance
The wheels on your vehicle were aligned and balanced carefully \
at the
factory to give you the longest tire
life and best overall performance.
In
most cases, you will not need to have your wheels aligned again.
However,
if you notice unusual tire wear or your vehicle pulling one way \
or
the other, the alignment may need to be reset. If you notice your vehicle
vibrating when driving on a smooth road, your wheels may need to be
rebalanced.
6-82
ProCarManuals.com
Page 362 of 436
Service & Appearance Care
Tire Chains
If your vehicle has dual wheels or LT265175R16 size tires, don’t use tire
chains; they can damage your vehicle.
__ you don’t have dual wheels or if you have a tire size other than
LT265/75R16, use tire chains only when you must. Use only
SAE
“S” type chains that are the proper size for your tires. Install \
them on the
tires of the rear axle. 3
Tighten the as tightly as possible with the ends securely fastened. Drive I
slowly and TOIIOW the chain manufacturer’s instructions. If you can hear the
chains contacting your vehicle, stop and retighten them.
If the contact
continues, slow down until
it stops. Driving too fast with chains on will ’
nage your vehicle.
1 CAUTION
Appearance Cam
I
Cleaning products can be hazardous. Some are toxic. Others can \
L burst into flame if you strike a match or get them on a hot part of
the vehicle. Some are dangerous
if you breathe their fumes in a
zlosed space. When you use anything in a container to clean your
vehicle, be sure
to follow the instructions. And always open your
doors or windows when you’re cleaning the inside.
I ter use these to clean your vehicle:
Gasoline
Benzene
Naphtha
Carbon Tetrachloride
Acetone
Paint Thinner
Turpentine
Lacquer Thinner
Nail Polish Remover
They can all be hazardous-some more than others-and they can
all damage your vehicle, too.
6-84
ProCarManuals.com
Page 364 of 436
Service & Appearance Care
Rinse the section with a clean, wet sponge.
Wipe off what’s left with a slightly damp paper towel or cloth.
Then dry it immediately with an air hose, a hair dryer or a heat lamp.
I
~~~
careful with a hair dryer or heat lamp. You could scorch me lauric.
Wipe with a clean cloth.
Using Solvent-Type Cleaner on Fabric
First, see if you have to use solvent-type cleaner at all. Some spots and
stains will clean
off better with just water and mild soap.
If you need to use it, then:
Gently scrape excess soil from the trim material with a clean,\
dull knife
or scraper. Use very little cleaner, light pressure and clean cloths
(preferably cheesecloth). Cleaning should start at the outside \
of the stain,
“feathering” toward the center. Keep changing to a clean section of the
cloth.
When you clean a stain from fabric, immediately dry the area with an
air hose, hair dryer,
or heat lamp to help prevent a cleaning ring. (See
previous NOTICE.)
Fabric Protection
Your vehicle has upholstery that has been treated with ScotchgardTM \
Fabric
Protector, a
3M product. ScotchgardTM protects fabrics by repelling oil and
water, which are the carriers of most stains. Even with this protection, you
still need to clean your upholstery often
to keep it looking new.
Further information on cleaning is available by calling 1-800-433-3296
(in
Minnesota, 1-800-642-61 67).
Special Cleaning Problems
Greasy or Oily Stains: Like grease, oil, butter, margarine, shoe polish, coffee
with cream, chewing gum, cosmetic creams, vegetable oils, wax c\
rayon, tar
and asphalt.
Carefully scrape off excess stain.
Then follow the solvent-type instructions above.
Shoe polish, wax crayon, tar and asphalt will stain if left on a vehicle
seat fabric. They should be removed as soon as possible. Be c\
areful,
because the cleaner will dissolve them and may cause them to bleed.
6-86
ProCarManuals.com
Page 366 of 436
![GMC SIERRA 1993 Manual PDF Service & Appearance Care
Don’t use abrasive cleaners on glass, because they may cause\
scratches.
Avoid placing decals on the inside rear window, since they may\
have to b](/img/44/57859/w960_57859-365.png "GMC SIERRA 1993 Manual PDF Service & Appearance Care
Don’t use abrasive cleaners on glass, because they may cause\
scratches.
Avoid placing decals on the inside rear window, since they may\
have to b")
Service & Appearance Care
Don’t use abrasive cleaners on glass, because they may cause\
scratches.
Avoid placing decals on the inside rear window, since they may\
have to be
scraped
off later. If abrasive cleaners are used on the inside of the rear
window, an electric defogger element may be damaged. Any tempor\
ary
license should not be attached across the defogger grid.
Cleaning the Outside of the Windshield and Wiper Blades
If the windshield is not clear
blade chatters when running,
windshield.
Clean the outside windshield
(GM Part No. 1050011). The
you rinse it with water. after using the windshield washer, or
if the wiper
wax or other material may be on the blade or
with
GM Windshield Cleaner, Bon-Ami Powder@
windshield is clean
if beads do not form when
Clean the blade by wiping vigorously with a cloth soaked
in full strength
washer solvent. Then rinse the blade with water.
Wiper blades should be checked on a regular basis and replaced\
when worn.
Cleaning the Outside of Your Vehicle
The paint finish on your vehicle provides beauty, depth of color, gloss
retention and durability.
Washing Your Vehicle
The best way to preserve your vehicle’s finish is to keep it clean by washing
it often with lukewarm or cold water.
Don’t wash your vehicle in the direct rays of the sun. Don’t use strong soaps
or chemical detergents. Use liquid hand, dish or car washing (\
non-detergent)
soaps. Don’t use cleaning agents that contain acid or abrasi\
ves.
All cleaning
agents should be flushed promptly and not allowed to dry on the surface, or
they could stain.
Dry the finish with a soft, clean chamois or a 100% cotton
towel to avoid surface scratches and water spotting.
High pressure vehicle washes may cause water to enter your veh\
icle.
Finish Care
Occasional waxing or mild polishing of your vehicle may be necessary to
remove residue from the paint finish. You can get
GM approved cleaning
products from your dealer. (See “Appearance Care and Materia\
ls’’ in the Index,)
Your vehicle (except
C 3500 HD) has a “basecoat/clearcoat” paint finish The
clearcoat gives more depth and gloss to the colored basecoat.
ProCarManuals.com
Page 368 of 436
Service & Appearance Care
Finish Damage
Any stone chips, fractures or deep scratches in the finish should be repaired
right away. Bare metal will corrode quickly and may develop into a major
repair expense.
Minor chips and scratches can be repaired with touch-up materia\
ls available
from your dealer or other service outlets. Larger areas of finish damage can
be corrected
in your dealer’s body and paint shop.
Underbody Maintenance
Chemicals used for ice and snow removal and dust control can \
collect on the
underbody.
If these are not removed, accelerated corrosion (rust) can occur \
on the underbody parts such as fuel lines, frame, floor pan, \
and exhaust
system even though they have corrosion protection.
At least every spring, flush these materials from the underbody wi\
th plain
water. Clean any areas where mud and other debris can collect.\
Dirt packed
in closed areas of the frame should be loosened before being flushed. Your
dealer or an underbody washing system can do this for you.
Chemical Paint Spotting
Some weather and atmospheric conditions can create a chemical fallout.
Airborne pollutants fall upon and attack painted surfaces on yo\
ur vehicle. This
damage
can take two forms: blotchy, ringiet-shaped discolorations, and small\
irregular dark spots etched into the paint surface.
Although no defect in the paint job causes this, General Motors will repair, at
no charge to the owner, the surfaces of new vehicles damaged by this fallout
condition within
12 months or 12,000 miles (20 000 km) of purchase,
whichever comes first. This applies only to materials manufactured and
sold
by General Motors. Bodies, body conversions or equipment not made or sold
by General Motors are not covered.
6-90
ProCarManuals.com
Page 370 of 436
Service & Appearance Care
Vehicle identification Number (VIN)
KO641
This is the legal identifier for your vehicle. It appears on a plate in the front
corner of the instrument panel, on the driver’s side. You c\
an see it if you
look through the windshield from outside your vehicle. The VIN also \
appears
on the Vehicle Certification and Service Parts labels and the \
certificates of
title and registration.
Engine Identification
The eighth character in your VIN is the engine code for your \
GM engine.
This code will help you identify your engine, specifications, a\
nd replacement parts in this section.
6-92
ProCarManuals.com
Page 372 of 436
Service & Appearance Care
Service Parts Identification Label
VEHICLE <
NUMBER IOENTlFlCATlOP
WMEELBASE
I
Service Par+s Identification 00 NOT REMOVE
PRlhlfD IN 0 5 A
I PAINT TECHNOLOGY
EXTERIORCOLORS ORDER
NUMBER
)- MODEL DESIGNATION
OPTION CONTENT
t
K2680
You’ll find this label on the inside of the glove box. It’s very helpful if you
ever need
to order parts. On this label is:
Your VIN.
Its model designation.
Paint information.
A list of all production options and special equipment.
Be sure that this label is not removed from the vehicle.
Add-on Electrical Equipment
I NOTICE
I lon’t add anything electrical to your vehicle unless you check with your
iealer first. Some electrical equipment can damage your vehicle and th\
e
iamage wouldn’t be covered by your warranty.
So just keep
3tther things from working as they should.
6-94
ProCarManuals.com
Page 374 of 436
Service & Appearance Care
Cooling Systen
VIN
ENGINE
K 5.7L
H 5.0L
Z 4.3L
CODE
~13500
H.D.
6.2L C
6.2L
J
6.5L F
7.4L
N
w/3500
H.D.
Capacity
QUA
Without NC
10.9 Quarts (10.3 Liters)
17.5 Quarts (16.5 Liters)
17.5 Quarts (1 6.5 Liters)
26.5 Quarts (25 Liters)
25 Quarts (23.5 Liters)
25 Quarts (23.5 Liters)
26.5 Quarts (25 Liters) 23 Quarts (22 Liters)
26.5 Quarts (25 Liters)
ITITY*
With NC
10.9 Quarts (10.3 Liters)
18 Quarts (17 Liters)
18 Quarts (17 Liters)
27 Quarts (25.5 Liters)
25 Quarts (23.5 Liters)
25 Quarts 123.5 Liters)
26.5 Quarts (25 Liters)
25 Quarts (23.5 Liters)
28.5 Quarts (27 Liters)
*All quantities are approximate.
*After refill, the level
MUST be checked as outlined under “Engine Cooling
System” in Section
5.
TO036
Crankcase Capacity
ENGINE
5.0L
With Filter
Without Filter VIN CODE
7 Quarts (6.5 Liters) - ct 6.2L
5 Quarts (4.8 Liters) 4 Quarts (3.8 Liters) H
6.2L Jt - 7 Quarts (6.5 Liters)
6.5L
*All quantities are approximate. 7
Quarts (6.5 Liters)
- Ft
*After refill, the level MUST be checked as outlined under “Engine Oil
4.3L
5 Quarts (4.8 Liters)
4 Quarts (3.8 Liters) K 5.7L**
4.5 Quarts (4.3 Liters)
4 Quarts (3.8 Liters) Z
7.4L** 7
Quarts (6.6 Liters)
6 Quarts (5.7 Liters) N
And Filter Recommendations” in Section 5.
**Add one additional quart for C3500 HD Models.
toil filter should be changed at
EVERY oil change.
TO1 79
6-96
ProCarManuals.com
Page 376 of 436
Service & Appearance Care
Light Bulb Data
6-98
ProCarManuals.com