lock GMC SIERRA CLASSIC 2007 Owners Manual

9. Position the center lift point of the jack under
the center of the spare tire.
10. Turn the wheel wrench clockwise to raise the
jack until it lifts the end tting.11. Continue raising the jack until the spare tire
stops moving upward and is held rmly in
place. The secondary latch has released and
the spare tire is balancing on the jack.
12. Lower the jack by turning the wheel wrench
counterclockwise. Keep lowering the jack
until the spare tire slides off the jack or
is hanging by the cable.
{CAUTION:
Someone standing too close during the
procedure could be injured by the jack. If
the spare tire does not slide off the jack
completely, make sure no one is behind
you or on either side of you as you pull
the jack out from under the spare.
13. Disconnect the jack handle from the jack.
Carefully remove the jack from underneath
the vehicle.
582

14. Use one hand to push against the spare while
rmly pulling the jack out from under the
spare tire with the other hand.
If the spare tire is hanging from the cable, insert
the hoist handle, extension, and wheel wrench
into the hoist shaft hole in the bumper and turn
the wheel wrench counterclockwise to lower the
spare the rest of the way.
15. Tilt the retainer at
the end of the cable
and pull it through
the wheel opening.
Pull the tire out
from under
the vehicle.16. Turn the wheel wrench clockwise to raise the
cable back up if the cable is hanging under
the vehicle.
Have the hoist assembly inspected as soon as
you can. You will not be able to store a spare or
at tire using the hoist assembly until it has
been replaced.
To continue changing the at tire, seeRemoving
the Flat Tire and Installing the Spare Tire on
page 571.
583

G. Hoist Shaft Access
Hole
H. Wheel WrenchI. Jack Handle
Extensions
J. Spare Tire Lock
(If Equipped)
1. Put the tire on the ground at the rear of the
vehicle with the valve stem pointed down,
and to the rear.
2. Tilt the retainer (D)
downward and
through the wheel
opening. Make
sure the retainer
is fully seated across
the underside of
the wheel.3. Attach the wheel wrench (H) and
extensions (I) as shown.
585

4. Insert the hoist
end (F) through the
hole (G) in the
rear bumper. Be
sure the hoist end of
the extension (F)
connects to the hoist
shaft (E). The
ribbed square end of
the extension is
used to lower
the spare tire.
5. Raise the tire part way upward. Make sure the
retainer (D) is seated in the wheel opening.
6. Raise the tire fully against the underside of
the vehicle by turning the wheel wrench
clockwise until you hear two clicks or feel it
skip twice. You cannot overtighten the cable.7. Make sure the tire is stored securely. Push,
pull (A), and then try to turn (B) the tire. If the
tire moves, use the wheel wrench to tighten
the cable.
8. Reinstall the spare tire lock (if equipped).
586

To store the jack and jack tools, do the following:
A. Wing Nut
B. Wheel Blocks
C. Retaining
Bracket and
Wing NutD. Wheel Wrench
and Extensions
E. Tool Bag
F. Mounting Bracket
G. Jack
H. Retaining Hook1. Put the tools (D) in the tool bag (E) and place
them in the retaining bracket (C).
2. Tighten down the wing nut (C).
3. Assemble the wheel blocks (B) and jack (G)
together with the wing nut (A) and
retaining hook (H).
4. Position the jack (G) in the mounting
bracket (F). Position the holes in the base of
the jack (G) onto the pin in the mounting
bracket (F).
5. Return them to their original location in the
vehicle. For more information, refer to
Removing the Spare Tire and Tools on
page 566for more information.
587

Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected
from short circuits by a combination of fuses, circuit
breakers and fusible thermal links. This greatly
reduces the chance of res caused by electrical
problems.
Look at the silver-colored band inside the fuse. If
the band is broken or melted, replace the fuse.
Be sure you replace a bad fuse with a new one of
the identical size and rating.
If you ever have a problem on the road and
don’t have a spare fuse, you can borrow one
that has the same amperage. Just pick some
feature of your vehicle that you can get along
without – like the radio or cigarette lighter – and
use its fuse, if it is the correct amperage. Replace
it as soon as you can.
Instrument Panel Fuse Block
The fuse block access
door is on the driver’s
side edge of the
instrument panel.
Pull off the cover to
access the fuse block.
To remove fuses, hold the end of the fuse
between your thumb and index nger and pull
straight out.
You may have spare fuses located behind the
fuse block access door. These can be used
to replace a bad fuse. However, make sure it
is of the correct amperage.
600

Fuses Usage
RR WPR Not Used
SEO ACCYSpecial Equipment Option
Accessory
WS WPR Windshield Wipers
TBC ACCYTruck Body Controller
Accessory
IGN 3 Ignition, Heated Seats
4WDFour-Wheel Drive System,
Auxiliary Battery
Fuses Usage
HTR A/C Climate Control System
LOCK (Relay)Power Door Lock Relay
(Lock Function)
HVAC 1 Climate Control System
LT DRDriver’s Door Harness
Connection
CRUISECruise Control, Power
Take Off (PTO)
UNLCK (Relay)Power Door Lock Relay
(Unlock Function)
RR FOG LP Not Used
BRAKE Anti-Lock Brake System
DRIVER UNLCKPower Door Lock Relay
(Driver’s Door Unlock
Function)
IGN 0 TCM
TBC IGN 0 Truck Body Controller
VEH CHMSLVehicle and Trailer High
Mounted Stoplamp
LT TRLR ST/TRN Left Turn Signal/Stop Trailer
601

Fuses Usage
LT TRNLeft Turn Signals and
Sidemarkers
VEH STOPVehicle Stoplamps, Brake
Module, Electronic Throttle
Control Module
RT TRLR ST/TRN Right Turn Signal/Stop Trailer
RT TRNRight Turn Signals and
Sidemarkers
BODY Harness Connector
DDM Driver Door Module
AUX PWR 2, M/GATE Not Used
LCKS Power Door Lock System
ECC, TPMTire Pressure Monitoring
System
TBC 2C Truck Body Controller
HAZRD Flasher Module
CB LT DRSLeft Power Windows
Circuit Breaker
TBC 2B Truck Body Controller
TBC 2A Truck Body ControllerCenter Instrument Panel Fuse Block
The center instrument panel utility block is
located underneath the instrument panel, to the
left of the steering column.
Device Usage
SEO Special Equipment Option
TRAILER Trailer Brake Wiring
UPFIT Uptter (Not Used)
SL RIDERide Control Harness
Connection
602

Device Usage
HDLR 2 Headliner Wiring Connector
BODY Body Wiring Connector
DEFOG Rear Defogger Relay
HDLNR 1 Headliner Wiring Connector 1
SPARE RELAY Not Used
CB SEATDriver and Passenger Seat
Module Circuit Breaker
CB RT DOORRight Power Windows Circuit
Breaker
SPARE Not Used
INFOInfotainment Harness
ConnectionUnderhood Fuse Block
The underhood fuse block in the engine
compartment on the driver’s side of the vehicle
near the battery. Lift the cover for access to
the fuse/relay block.
To remove fuses hold the end of the fuse between
your thumb and index nger and pull straight out.
SeeEngine Compartment Overview on page 480
for more information on its location.
603

1*Fuel Injection Rail #2-Gasoline Engine; Engine
Control Module-Diesel Engine.
2*Fuel Injection Rail #1-Gasoline Engine;
Actuator-Diesel Engine.
3*Oxygen Sensors-Gasoline Engine; Fuel
Heater-Diesel Engine.
4*Oxygen Sensors-Gasoline Engine; Engine
Control Module 1-Diesel Engine.
5*Ignition 1-Gasoline Engine; Engine Control
Module-Diesel Engine.
6*Powertrain Control Module B-Gasoline Engine;
Engine Control Module B-Diesel Engine.
7*Supplemental Brake Assist - Gasoline Engine;
Electronic Viscous Fan - Diesel Engine.
8*Rear Climate Control.
9*Sunroof.Fuses Usage
GLOW PLUGDiesel Glow Plugs and Intake
Air Heater
CUST FEED Gasoline Accessory Power
HYBRID Hybrid
STUD #1Auxiliary Power (Single
Battery and Diesels Only)/
Dual Battery (TP2) Do not
install fuse.
MBECMid Bussed Electrical Center
Power Feed, Front Seats,
Right Doors
BLWR Front Climate Control Fan
LBECLeft Bussed Electrical Center,
Door Modules, Door Locks,
Auxiliary Power Outlet—Rear
Cargo Area and Instrument
Panel
STUD #2*Accessory Power/Trailer
Wiring Brake Feed
ABS Anti-lock Brakes
VSES/ECAS Vehicle Stability
IGN A Ignition Power
IGN B Ignition Power
605