keyless entry GMC YUKON 2004 Get To Know Guide

Arm the system
•Lock the doors using
the power door lock
switch or the Keyless
Entry System trans-
mitter. The alarm is
activated when the symbol shown
above illuminates in the instrument
panel cluster (approximately 30
seconds).
If your vehicle is equipped with a Driver
Information Center, you can program the
alarm to the following:
Manually activate the headlamps, all
exterior tail/marker lamps and the
instrument panel/radio lights
•Turn the exterior lamps knob to this
position ( ).
Turn the fog lamps (if equipped) on
or off
•Press the fog lamp
button located on
the left side of the
instrument panel.
An indicator lamp
will illuminate when
the fog lamps are on.
See Section 3 of your Owner Manual.11
Daytime Running Lamps (DRL)
Disable the DRL when idling
•Shift the vehicle into PARK, or
•Set the parking brake.
See Section 3 of your Owner Manual.
Content Theft-Deterrent System
(if equipped)
•Both Horn/Headlamps
•Horn only
•Lamps only
•Off
See Section 2 of your Owner Manual.
Note:Your vehicle’s factory default
setting is Horn and Lamps. See the
Personalizing Your Vehicle section of
this booklet for more information.
Tire Pressure Monitor
(if equipped)
This feature alerts you when a
substantial reduction in pressure occurs
in one of your vehicle’s tires. If this
occurs, a CHECK TIRE PRESSURE
message will appear in the instrument
panel cluster. This message will remain
on until you reset the system.
Reset the tire pressure monitor
•To reset the tire pressure message,
you must fill the tires with the correct
amount of air. The best time to check
your tire pressure is when the tires
are cold.
•Pressing the cluster stem button on
your instrument panel cluster or the
Select/Reset button ( ) on your
steering wheel (if equipped) will
temporarily eliminate the message.
However, at the next vehicle start-up,
the message will reappear. The tire
pressure must be corrected to
permanently eliminate the message.
See Section 5 of your Owner Manual.
Note:The Tire Pressure Monitor
can alert you about low tire pressure,
but it doesn’t replace normal tire
maintenance.
Note:Your DRLs will re-engage at the
next key cycle.

Getting to Know YourYukon/Yukon Denali12
Memory Positions for Driver’s
Seat, Mirrors, Pedals, Radio and
Climate Controls (if equipped)
Use the driver’s
door mounted con-
trols to:
•Adjust driver
seat, including
lumbar
adjustment
•Adjust gas and
brake pedals
•Adjust the outside rearview mirrors
•Set the radio presets and climate
control temperature (the temperature
setting will revert to the last tempera-
ture setting used)
•Press and hold Memory 1 or 2 until
two chimes sound (about four
seconds)
•To set up for another driver, repeat
the process with the other memory
button
These settings will be remembered after
they are programmed by pressing the
Memory 1 or 2
button on the
driver’s door
(shown above).
If you unlock the
vehicle with the
Remote Keyless
Entry (RKE)
transmitter, the
vehicle memory
settings will correspond to the number
on the RKE transmitter: 1 or 2.
See Section 2 of your Owner Manual.
Memory Settings for Your
Vehicle (Driver Information
Center) (if equipped)
Your vehicle may be programmed with
the features shown below. To cycle
through them, use the
Personalization/Menu button ( )
located on your steering wheel.
•Alarm Warning Type
•Automatic Locking/Unlocking
•Perimeter Lighting
•Delayed Locking
•Remote Lock/Unlock Feedback
•Seat Position Recall
•Headlamps On at Exit
•Easy Exit Driver Seat
•Display Units
•Display Language
•Curb View Assist (if equipped)
Selection Options
Use the Select button ( ) to choose
your desired setting. The last setting
remaining on the display will be
the selection of choice. Continue
cycling through the menu with the
Personalization/Menu button ( )
to set other preferences.
Alarm W
arning Type
1. Alarm Warning: Both (default)
2. Alarm Warning: Off
3. Alarm Warning: Horn
4. Alarm Warning: Lamps