transmission GREAT WALL SAFE 2006 User Guide

TF-11
5. Tear down the Chain drive system
Take apart the following parts from the transfer box housing
assembly.
(a) Take apart the snapping ring and washer from the front
output shaft.
(b) Take apart the driving chain sprocket, driven chain
sprocket and drive chain together from the two output
shafts.
(c) Separate the chain sprocket from the chain.
12
345
6 7
1. output shaft
2. driving chain sprocket
3. driven chain sprocket
4. washer
12 34
5
6 7
6. Oil pump assembly
Take apart the shaft and pump assembly, pipe clip, oil pipe and
filter from the remaining transfer box housing assembly.
1
2
7
6 3
4
5
8 1. deceleration gear hub
2. inserted face of Shift
toggle fork
3. plastic sleeve
4. contact roller
5. pin
6. pin, contact roller and sleeve assembly
7. deceleration shift toggle fork
8. deceleration shift toggle fork assembly7. Deceleration shifting element disassembly
Tear down the following parts from the remaining transfer box
housing assembly.
(a) Take apart the deceleration hub, and deceleration shift
fork assembly from the housing.
(b) Take apart two plastic inserted faces from the decelera-
tion shift fork assembly
(c) Disassembly the deceleration shift fork assembly only if
it were broken.Cut the plastic cover,and take out the pin
and truckle. Transfer Box
Disassembly of Transfer Box
1. output shaft
2. driving chain sprocket
3. driven chain sprocket
4. washer
5. snapping ring
6. transmission chain
7. front output shaft5. snapping ring
6. transmission chain
7. front output shaft

TF-19
1
9
8
7
6
5
4
32
10
11
12
345
6 7
Transfer Box
Transfer Box Assembly
9. Assembly of driving chain
The parts assembly process is as follows:
(a) Put the driving chain sprocket at the rear end of the output
shaft, and the driven chain sprocket is put at the rear end
of the front output shaft on the worktable after the transfer
box housing assembly mount.
(b) Mount the chain on the sprocket.
(c) Holding the two chain sprockets parallel with the transfer
box in the space that the chain on the two sprockets are
straightened, and encase the chain and sprocket assembly
through the output shaft, it is required to run the chain
sprocket slowly to ensure that they engage with the front
output shaft and the spline.
(d) Mount the gasket and snapping ring on the front output
shaft.
10. Shift locking element assembly
The parts mounting process is as follows (for the electric shift
transfer box):
(a) Mount the return spring and locking hub on the locking
sleeve and fasten them with snapping ring to finish the
2W-4W locking sleeve assembly.
(b) Encase the shift guide shaft in the blind hole of the
housing through the deceleration toggle fork assembly
that is already assembled.
(c) Mount the shift toggle fork on the 2W-4W locking sleeve
assembly, which will slide through the shift guide shaft
and rear output shaft.
(d) Joint the combined external gear sleeve spline and the
rear output shaft spline as well as the 2W-4W locking
sleeve.
1. output shaft
2. driving chain sprocket
3. driven chain sprocket
4. washer
5. snapping ring
6. transmission chain
7. front output shaft
1. output shaft
2. shift engagement
sleeve assembly
3. locking sleeve
4. return spring
5. engagement sleeve6. snapping ring
7. shift lock hub
8. clutch assembly
9. fastening snapping ring
10. shift guide shaft
11. toggle fork

PR-6Drive Shaft
Drive Shaft
3. Take apart the drive shaft from the gearbox.
(a) Pull out the universal joint yoke from the gearbox.
(b) Insert the SST in gearbox to prevent the oil leakage
Front axle drive shaft
4. Tear down the front universal joint flange fork of the front
drive shaft.
(a) Hang he front end of the front axle drive shaft.
(b) Label the assembly mark on the flange
(c) Take apart the four sets of bolt and nut.
5. Disconnect the rear universal joint flange fork from the
front axel drive shaft along the transmission path.
(a) Label the assembly marks on each flange.
(b) Take apart the four sets of bolt and nut.
Drive shaft disassembly
1. Separation of the rear joint of the rear axle drive shaft
from the front joint of rear axle drive shaft
(a) Label the assembly marks on each flange.
(b) Take apart the four sets of bolt and nut.
2. Take apart the center support bearing from the front joint
of the rear axle drive shaft.
(a) Loosen the riveted nut by chiseling with a chisel and
hammer.
SST
assembly mark
assembly mark

B0-29
SJSJ
SJVehicle Body
Wheel-Trims Wrapping Angle and Exterior Trim Panel
Change of trim panel at front door
1. Tear down the trim panel at front door;
Prize up the clip of trim panel at front door and take down the
trim panel at front door. (SJ)
Uncover the luminous strip to tear down the five screws, then
open the front door and take down the trim panel at front door
after tearing down the five screws. (top-grade SY)
Change of front wrapping angle
1. Tear down the front wrapping angle;
Tear down the three screws and take down the front wrapping
angle and adhesive strip of wrapping angle lightly (there is two
screws in top-grade SY vehicle)
2. Mount the front wrapping angle
(a) Mount on the three screws (mount two screws for top-
grade SY vehicle)
(b) Contact the front wrapping angle with the front bar
closely, and the seam between the front wrapping angle
and the front Wheel-trims should be even with a smooth
transmission (by the way, the adhesive strip of wrapping
angle should be pressed tightly and evenly)
Change of front Wheel-trims
1. Tear down the front Wheel-trims
Tear down the four screws and the pressing plate of mudguard,
and take down the front Wheel-trims and adhesive strip of
Wheel-trims tightly (SY)
Tear down the five screws and the pressing plate of mudguard,
and take down the front Wheel-trims and adhesive strip of
Wheel-trims tightly (SJ)
Tear down the four screws and uncover the lighting channel of
the front Wheel-trims, take down the front Wheel-trims after
tearing down one screw (top-grade SY).
2. Mount the front Wheel-trims
(a) Flush the front end of front Wheel-trims with the lower
edge of wing panel; the adhesive strip of wheel-trims
should be pressed tightly and evenly. (SY)
Flush the front end of front Wheel-trims with the lower
edge of wing panel, the rear end of front Wheel-trims
with rear edge of wing panel. (top-grade SY SJ)
(b) Mount the four screws (five screws for SJ model) and the
pressing plate of mud guard and stick the lighting strip.
(top-grade SY)

B0-30
Top-grade SY
SJ
SJ Top-grade SYVehicle Body
Wheel-Trims Wrapping Angle and Exterior Trim Panel
2. Mount the trim panel at front door;
(a) Flush the arc lines of the front and rear ends of trim panel
at front door in consistent with the door waist line, and the
rear end should flush with the rear end of front door, but
the front end should not interfere with the wing panel.
(b) Tap the positions of six clipes of trim panel at front door
manually to mount it on.(SJ)
Mount the five screws at upper part after aligning the
holes, and mount the five screws at lower part from the
inside, then stick the luminous strip. (top-grade SY)
Change of rear Wheel-trims
1. Tear down the rear Wheel-trims;
Tear down the three screws and take down the rear Wheel-
trims and the adhesive strip of Wheel-trims. (SY)
Take down the rear Wheel-trims after tearing down the three
screws. (SJ)
Tear down the three screws and uncover the luminous strip on
rear Wheel-trims, take down the rear Wheel-trims after tearing
down the two screws. (top-grade SY)
Change of trim panel at rear door
1. Tear down the trim panel at rear door
Take down the trim panel at rear door after tearing down one
screw and four clipes. (SJ)
Uncover the luminous strip to tear down the four screws, and
then open the rear door to tear down the four screws inside so
as to take down the trim panel at rear door. (top-grade SY)
Top-grade SY
2. Mount the trim panel at rear door
Tap the positions of four clipes of trim panel at rear door
manually to mount it on, meanwhile mount the one screw at
upper part of rear edge. (SJ)
Mount the four screws at upper part after aligning the holes,
and mount the four screws at lower part from the inside, then
stick the luminous strip. (top-grade SY)
2. Mount the front Wheel-trims
(a) Flush the front end of rear Wheel-trims with the edge line
of rear door, the rear end of the Wheel-trims with the rear
wrapping angle, the seam should be smooth with even
transmission. (top-grade SY SJ)
(b) Mount the three screws (and mount two screws at the
position where the luminous strip is stickled).