ABS HONDA ACCORD 2001 CF / 6.G User Guide

Ø Ø ØØØ Ø ØØ ØØ ØØØØØØØØØ Ø ØØØØØØ
Î
ÌÌ
Ì Î
Maint enance225
A, B, C
Canadian owners:
AB C D
Service at the indicated distance or time, whichever comes first. Do the items in as required for each distance/time interval. Follow this
schedule if the severe driving conditions described in the Severe Conditions Schedule on the next page do not apply.
Follow the schedule for Severe Conditions.
7,500 mi/12,000 km
15,000 mi/24,000 km/1 yr
22,500 mi/36,000 km
30,000 mi/48,000 km/2 yrs
37,500 mi/60,000 km
45,000 mi/72,000 km/3 yrs
52,500 mi/84,000 km
60,000 mi/96,000 km/4 yrs
67,500 mi/108,000 km
75,000 mi/120,000 km/5 yrs
82,500 mi/132,000 km
90,000 mi/144,000 km/6 yrs
97,500 mi/156,000 km
105,000 mi/168,000 km/7 yrs
112,500 mi/180,000 km
120,000 mi/192,000 km/8 yrs
At 120,000 mi/200,000 km/10
years, thereafter every 60,000
mi/100,000 km) or 60 months
Every 120,000 mi/192,000 km/72months
At 120,000 mi/192,000 km or 72
months, thereafter every 90,000
mi/144,000 km/or 60 months Do items in A.
Do items in A, B.
Do items in A.
DoitemsinA,B,C.
Do items in A.
Replace brake fluid. Do items in A, B, D.
Do items in A.
DoitemsinA,B,C.
Do items in A.
Do items in A, B.
Do items in A. Replace brake fluid. Do items in A, B, C, D.
Do items in A.
Replace timing belt, balancer belt , inspect
water pump. Inspect valve clearance. Check idle speed.
Replace spark plugs. Do items in A, B.
Do items in A.
DoitemsinA,B,C. Replace engine coolant
Replace manual transmission fluid
Replace automatic transmission fluid Replace engine oil.
Rotate tires (follow pattern on page ).
Replace engine oil filter.
Inspect front and rear brakes.
Check parking brake adjustment.
Inspect tie rod ends, steering gear box and boots.
Inspect suspension components.
Inspect driveshaft boots.
Inspect brake hoses and lines (including ABS).
Check all fluid levels, condition of fluids, and check
for leaks.
Inspect cooling system hoses and connections.
Inspect exhaust system.
Inspect fuel lines and connections.
Replace air cleaner element.
Inspect and adjust drive belts.
Replace air conditioning filter.
Replace brake fluid every 3 years.
(independent of mileage) 271
1 Balancer belt applies to 4-cylinder models only.
See information on maintenance and emissions warranty, last
column, page .
:
1: 223
Maintenance Schedule for Normal Conditions (listed by distance/time)

µ
Ì
Î ÎÎ ÌÌ
ÌÎÎ
Î
Î Follow the Maintenance
Schedule f or Severe Conditions.
Follow the Severe Conditions
Maintenance Schedule if you
drive your vehicle
under one or more of the
f ollowing conditions:
Driving less than 5 miles (8
km) per trip or, in f reezing
temperatures, driving less
than 10 miles (16 km) per trip.
Driving in extremely hot
[over 90°F (32°C)] conditions.
Extensive idling or long
periods of stop-and-go driving.
Trailer towing, driving with a
car top carrier, or driving in
mountainous conditions.
Driving on muddy, dusty, or
de-iced roads.
MAINLY
Maint enance U.S. Owners
Canadian Owners
226 Visually inspect the following items:Replace every 3,750 miles (6,000 km) or 6 months
Check oil and coolant at each fuel stop
Service at the indicated
distance or time whichever
comes first.
miles x 1,000
km x 1,000
months
See air conditioning filter on page for replacement information under special driving conditions.
Balancer belt applies to 4-cylinder models only.
See timing belt on page to determine need for replacement.
See information on maintenance and emissions warranty, last column, page .
Tie rod ends, steering gear box, and boots
Suspension components, driveshaft boots
Brake hoses and lines (including ABS)
All fluid levels and conditions of fluids
Cooling system hoses and connections
Exhaust system, fuel lines and connections
Lights and controls, vehicle underbody Every 7,500 miles (12,000 km) or 6 months
Replace engine oil and oil filter
Check engine oil and coolant
Clean ( ) or replace ( ) air cleaner element
Use normal schedule except in dusty conditons
Inspect valve clearance
Replace spark plugs
Replace timing belt , balancer belt , and
inspect water pump
Inspect and adjust drive belts
Inspect idle speed
Replace engine coolant
Replace transmission fluid
Inspect front and rear brakes
Replace brake fluid
Check parking brake adjustment
Replace air conditioning filter
Lubricate all hinges, locks and latches
Rotate tires (Check tire inflation and condition
at least once per month) Rotate tires every 7,500 miles (12,000 km)
152412
304824 457236609648 75
120 60 105168
84 120192
96
90
144
72
At 60,000 miles (96,000 km) or 36 months, thereafter every 30,000 mi, (48,000 km) or 24 months
At 60,000 miles (96,000 km) or 36 months
Every 36 months
Adjust only if noisy
:
1:2:3: 223
267
266 Every 7,500 miles (12,000 km) or 6 months
MTAT
11
,2
3
120,000 miles (200,000 km) or 10 years, thereafter every 60,000 miles (100,000 km) or 60 months
Maintenance Schedule for Severe Conditions

Ø Ø Ø ØØØØØØØØ
Ø Ø
Ø
ØØ Ø Ø Ø Ø Ø Ì Ì
Î
ÎÎ
Î
ÎÎ Î
Ì Î ÎÎ
Maint enance
228 D E
82,500 mi/132,000 km
86,250 mi/138,000 km
90,000 mi/144,000 km/6 yrs
93,750 mi/150,000 km
97,500 mi/156,000 km
101,250 mi/162,000 km
105,000 mi/168,000 km/7 yrs
108,750 mi/174,000 km
112,500 mi/180,000 km
116,250 mi/186,000 km
120,000 mi/192,000 km/8 yrs
At 120,000 mi/200,000 km/72
months, thereafter every
60,000 mi/100,000 km/60 mos
Every 60,000 mi/96,000 km/36mos
At 60,000 miles/96,000 km or
36 months, thereafter every
30,000 mi/48,000 km/24 mos Inspect brake hoses and lines (including ABS).
Check all fluid levels, condition of fluids, and check
for leaks.
Inspect cooling system hoses and connections.
Inspect exhaust system.
Inspect fuel lines and connections.
Check all lights.
Inspect the underbody.
Replace air cleaner element.
Inspect and adjust drive belts.
Replace air conditioning filter .
Replace brake fluid every 3 years.
(independent of mileage)
Do items in A, B.
Do items in A.
Replacebrakefluid.DoitemsinA,B,C,D,E.
Do items in A.
Do items in A, B.
Do items in A. Replace timing belt , balancer belt , and
inspect water pump. Inspect valve clearance. Check idle speed. Clean air cleaner element.
Replace spark plugs. Do items in A, B, C.
Do items in A.
Do items in A, B.
Do items in A.
Replace timing belt , balancer belt , and
inspect water pump. Do items in A, B, C, D.
Replace engine coolant
Replace manual transmission fluid
Replace automatic transmission fluid See air conditioning filter on page for replacement information
under special driving conditions.
Balancer belt applies to 4-cylinder models only.
See timing belt on page to determine need for replacement.
See information on maintenance and emissions warranty, last
column, page .
:
1:2:3: 223
267
2663
11
,2
11 ,2
Maintenance Schedule for Severe Conditions (listed by distance/time)

Remove the blade f rom its holder
by grasping the tabbed end of the
blade. Pull f irmly until the tabs
come out of the holder.Examine the new wiper blades. If
they have no plastic or metal rein-
f orcement along the back edge,
remove the metal reinf orcement
strips f rom the old wiper blade and
install them in the slots along the
edge of the new blade.Slide the new wiper blade into the
holder until the tabs lock.
Lower the wiper arm down against
the windshield.
Slide the wiper blade assembly
onto the wiper arm. Make sure it
locks in place.
Lower the passenger’s side f irst,
then the driver’s side.
3. 4. 5. 6.
7.
Wiper Blades
Maint enance
264
RREEIINNFFOORRCCEEMMEENNTT
BBLLAADDEEBBLLAADDEE

When shopping f or replacement
tires, you may find that some tires
are ‘‘directional.’’ This means they
are designed to rotate only in one
direction. If you use directional tires,they should be rotated only front-to-
back.
To help increase tire lif e and
distribute wear more evenly, you
should have the tires rotated every
7,500 miles (12,000 km). Move the
tires to the positions shown in the
chart each time they are rotated.
Make sure the installer balances the
wheels when you have new tires
installed. This increases riding
comf ort and tire lif e. Your car’s
original tires were dynamic or ‘‘spin’’
balanced at the f actory. For best
results, have the installer perf orm a
dynamic balance.
The tires that came with your car
were selected to match the perform-
ance capabilities of the car while
providing the best combination of
handling, ride comf ort, and long lif e.
Youshouldreplacethemwithradial
tires of the same size, load range,
speed rating, and maximum cold tire
pressure rating (as shown on the
tire’s sidewall). Mixing radial and
bias-ply tires on your car can reduce
its braking ability, traction, and
steering accuracy.
(LX with ABS, EX, EX-V6)
CONT INUED
Tire Rotation
Replacing T ires and Wheels
Tires
Maint enance271
FFrroonnttFFrroonntt
((FFoorrNNoonn--ddiirreeccttiioonnaallTTiirreessaannddWWhheeeellss))((FFoorrDDiirreeccttiioonnaallTTiirreessaannddWWhheeeellss))
Improper wheel weights can damage
your car’s aluminum wheels. Use only
Genuine Honda wheel weights f or
balancing.

Tire:
Wheel:
If you ever need to replace a wheel,
make sure the wheel’s specif ications
match those of the original wheel
that came on your car. Replacement
wheels are available at your Honda
dealer.
It is best to replace all f our tires at
thesametime.If thatisnotpossible
or necessary, then replace the two
f ront tires or the two rear tires as a
pair. Replacing just one tire can
seriously af f ect your car’s handling. TheABSworksbycomparingthe
speed of the wheels. When replacing
tires, use the same size originally
supplied with the car. Tire size and
construction can af f ect wheel speed
and may cause the system to work
inconsistently.
See page f or inf ormation about
DOT Tire Quality Grading.
(DX)
(LX, EX)
(LX-V6, EX-V6)
(DX)
(LX, EX)
(LX-V6, EX-V6)
329
Wheels and T ires
Tires
Maint enance
272 P195/70R14 90S
14x51/2JJ
15x6JJ
15x61/2JJ
P195/65R15 89H
P205/65R15 92V
Installing improper tires on your
car can affect handling and
stability. This can cause a crash
in which you can be seriously
hurt or killed.
Always use the size and type of
tires recommended in this
owner’s manual.

Open the trunk and remove the
socket f rom the light assembly by
turning it one-quarter turn counter-
clockwise.
Remove the burned-out bulb by
pulling it straight out of the socket.
Install the new bulb and reinstall
the socket. Make sure the new
bulb is working.Remove the license light assembly
by caref ully prying on the lef t
edge of the lens with a f lat-tip
screwdriver and pulling the
assembly out.
Remove the lens f rom the bulb
holder by pulling the lens while
squeezing the tabs on both sides
of the holder.
1.
2. 3. 1.
2.
CONT INUED
Replacing a High-mount Brake
Light BulbReplacing a Rear License Bulb
Lights
Maint enance
281
BBUULLBB

Remove the bulb by pulling it
straight out of its metal tabs.
Push the new bulb into the metal
tabs. Snap the lens back in place.
The ceiling light, door light and
vanity mirror light come apart the
same way, but they do not use the
same type of bulb.
Removethelensbycarefully
prying on the edge of the lens with
a f ingernail f ile or a small f lat-tip
screwdriver. Do not pry on the
edge of the housing around the
lens.
Turn on the parking lights and
check that the new bulb is
working.
Pull the bulb straight out of its
socket. Push the new bulb in until
it bottoms in the socket.
Put the lens back on the bulb
holder and push it until it latches.
Slide the lef t side of the light
assembly into the hole. Push on
the right side to latch the
assembly into place. Door light:
Pry on the top middle of the lens.
Ceiling light: Pry on the f ront edge of the lens
near both sides.
Spotlight:
pry on the f ront edge in f ront of
both spotlights.
1.
4. 5.
2. 3.
3. 6.
Not available on DX model
Not available on DX model
Replacing Bulbs in the Interior
Lights
Lights
Maint enance
282
CCEEIILLIINNGGLLIIGGHHTT

Open the trunk. Pull down the
trunk light cover.
Remove the bulb by pulling it
straight out of its metal tabs.
Push the new bulb into the metal
tabs.
Push the cover back in place.
1. 2.3.4.
Replacing the T runk L ight Bulb
Lights
Maint enance
284
TTRRUUNNKKLLIIGGHHTT

µµ
Always wash and dry the whole car
bef ore waxing it. You should wax
your car, including the metal trim,
whenever water sits on the surf ace
in large patches. It should f orm into
beads or droplets af ter waxing.
You should use a quality liquid or
paste wax. Apply it according to the
instructions on the container. In
general, there are two types of
products:
Waxes A wax coats the finish and
protects it f rom damage by exposure
to sunlight, air pollution, etc. You
should use a wax on your Honda
when it is new.
Polishes Polishes and cleaner/
waxes can restore the shine to paint
that has oxidized and lost some of its
shine. They normally contain mild
abrasives and solvents that remove
the top layer of the f inish. You should use a polish on your Honda if
the f inish does not have its original
shine af ter using a wax.
Cleaning tar, insects, etc. with
removers also takes off the wax.
Remember to re-wax those areas,
even if the rest of the car does not
need waxing.
Clean your Honda’s aluminum alloy
wheels as you do the rest of the
exterior.Washthemwiththesame
solution, and rinse them thoroughly.
The wheels have a protective clear-
coat that keeps the aluminum from
corroding and tarnishing. Using
harsh chemicals, including some
commercial wheel cleaners, or stif f
brushes can damage this clear-coat.
Only use a mild detergent and sof t
brush or sponge to clean the wheels.
Your dealer has touch-up paint to
match your car’s color. The color
code is printed on a sticker on the
driver’s doorjamb. Take this code to
your dealer so you are sure to get
the correct color.
Inspect your car f requently f or chips
or scratches in the paint. Repair
them right away to prevent corrosion
of the metal underneath. Use the
touch-up paint only on small chips
and scratches. More extensive paint
damage should be repaired by a
prof essional.
On LX with ABS, EX and EX-V6 models
Exterior Care
Appearance Care
Waxing
Paint T ouch-up
A luminum Wheels
289