HONDA ACCORD 2004 CL7 / 7.G Manual PDF

Controls Near the Steering Wheel
Inst rument s and Cont rols72
WINDSHIELD
WIPERS/WASHERS
MOONROOF
SWITCH HEADLIGHTS/
TURN SIGNALS
TRACTION CONTROL SYSTEM HORN TILT/TELESCOPIC
ADJUSTMENT
INSTRUMENT PANEL BRIGHTNESS
(P.102) HAZARD
WARNING LIGHTS
CRUISE CONTROLS
REAR WINDOW
DEFOGGER
SEAT HEATERSPASSENGER AIRBAG
OFF INDICATOR
(P.31)
(P.76)
(P.74)
(P.191) (P.78)(P.73)
(P.76)
(P.155)
(P.77, 113, 116)
(P.91)
——y

y
(
yy

µ
µ
µ µ
µ µ
µ
µ µ
MIST
OFF
INT Intermittent
LO Low
HI High
Windshield Washers Push the right lever up or down to
select a position.
The wipers run at high
speed until you release the lever.
The wipers are not activated. The wipers run at low speed.
The wipers run at high speed.
The length of the wiper
interval is varied automatically
according to the vehicle’s speed.
Vary the delay by turning the INT
TIME ring. If you turn it to the
shortest delay, the wipers will
change to low speed operation when
the vehicle speed exceeds 12 mph
(20 km/h). Pull the
wiper control lever toward you and
hold it. The washers spray until you
release the lever. The wipers run at
low speed, then complete one more
sweep after you release the lever.
1.2.3.4.5.6.
Windshield Wiper
MIST
OFFLO HI
INT Windshield Washer
Wipers and Washers
Inst rument s and Cont rols73
——y


y
(
yy

µµ
Turn Signal
Of f
Parking and interior lights
Headlight on
High beams
FlashhighbeamsPush down on the
lef t lever to signal a lef t turn and up
to signal a right turn. To signal a lane
change, push lightly on the lever in
the proper direction and hold it. The
lever will return to center when you
release it or complete a turn. Rotating the
switch on the lef t lever to the
‘‘ ’’ position turns on the parking
lights, taillights, instrument panel
lights, side-marker lights, and rear
license plate lights. Turning the
switch to the ‘‘ ’’ position turns
on the headlights. If you leave the
lights on with the ignition switch in
ACCESSORY (I) or LOCK (0), you
will hear a reminder chime when you
open the driver’s door.
When the light switch is in either of
these positions, the Lights On
indicator comes on as a reminder.
1.2.3.4.5.6.
T urn Signal and Headlights T urn Signal Headlights ON
Turn Signal, Headlights
Inst rument s and Cont rols74
——y

y
(
yy

µThis f eature turns of f the headlights,
parking lights, taillights, and license
plate light within 15 seconds of
removing the key from the ignition
switch and closing the driver’s door.
This feature activates if you leave
the headlight switch in the ‘‘ ’’
or ‘‘ ’’ position, remove the key,
then open and close the driver’s door. If you remove the key f rom the
ignition switch with the headlight
switch on, but do not open the door
and get out, the lights will turn of f
af ter 10 minutes.
The lights will turn on again when
you unlock or open the driver’s door.
If you unlock the door, but do not
open it within 15 seconds, the lights
will go of f . With the driver’s door
open, you will hear a lights-on
reminder chime.
To turn on, push
the lever f orward until you hear a
click. The blue high beam indicator
will light (see page ). Pull it back
to return to low beams. To flash the
high beams, pull the lever back
lightly, then release it. The high
beams will stay on as long as you
hold the lever back. 66
On all U.S. and Canadian models except
DX
Automatic Lighting Of f Feature
High Beams
Headlights, Automatic Lighting Of f Feature
Inst rument s and Cont rols75
——y

y
(
yy

With the headlight switch off, the
high beam headlights and the high
beam indicator come on with
reduced brightness when you turn
the ignition switch to ON (II) and
release the parking brake. They
remain on until you turn the ignition
of f , even if you set the parking brake.
The headlights revert to normal
operation when you turn them on
with the switch.The knob on the instrument panel
controls the brightness of the instru-
ment panel lights. Turn the knob to
adjust the brightness.Push the button between the center
vents to turn on the hazard warning
lights (f our-way f lashers). This
causes all f our outside turn signals
and both turn indicators in the
instrument panel to f lash. Use the
hazard warning lights if you need to
park in a dangerous area near heavy
traf f ic, or if your vehicle is disabled.
Instrument Panel Brightness Hazard Warning
Daytime Running L ights
(Canadian Models)
Daytime Running L ights, Instrument Panel Brightness, Hazard Warning
Inst rument s and Cont rols76
INSTRUMENT PANEL BRIGHTNESS KNOB
——y

y
(
yy

Make sure the rear window is clear
and you have good visibility bef ore
starting to drive.
The def ogger and antenna wires on
the inside of the rear window can be
accidentally damaged. When
cleaning the glass, always wipe side
to side.
The rear window def ogger will clear
fog,frost,andthinicefromthe
window. Push the def ogger button to
turn it on and off. The indicator
above the button lights to show the
def ogger is on. It also shuts of f when
you turn off the ignition. You have to
turn it on again when you restart the
vehicle.
Rear Window Def ogger
Inst rument s and Cont rols77
Manual A/C type shown
——y

y
(
yy

Insert the key in the ignition
switch, and unlock the steering
column.
Push the lever under the steering
column all the way down.Move the steering wheel up or
down, and in or out to the desired
position, making sure the wheel
points toward your chest, not
towardyourface.Makesureyou
can see the instrument panel
gauges and the indicator lights.
Make any steering wheel adjustment
bef ore you start driving.
1. 2.
3.See page f or important saf etyinf ormation about how to properlyposition the steering wheel. 16
Steering Wheel A djustment
Inst rument s and Cont rols78
Adjusting the steering wheel
position while driving may
cause you to lose control of the
vehicle and be seriously injured
inacrash.
Adjust the steering wheel only
when the vehicle is stopped.
——y

y
(
y
y

Push the lever up to lock the
steering wheel in that position.
Make sure you have securely
locked the steering wheel in place
by trying to move it up, down, in,
and out.
4. 5.
Keys and Locks
Steering Wheel A djustment, K eys and L ocks
Inst rument s and Cont rols79
MASTER
KEY
(BLACK)
MASTER
KEY WITH
REMOTE
TRANSMITERVALET KEY
(LIGHT GREY)
Only on DX models On all models except DX
KEY
NUMBERTAG
KEY
NUMBERTAG
VALET KEY
(LIGHT GREY)
——y


y
(
yy

Youshouldhavereceivedakey
number tag with your keys. You will
need this key number if you ever
have to get a lost key replaced. Use
only Honda-approved key blanks.
These keys contain electronic
circuits that are activated by the
Immobilizer System. They will not
work to start the engine if the
circuits are damaged.Protect the keys f rom direct
sunlight, high temperature, and
high humidity. Donotdropthekeysorsetheavy
objects on them.
Keep the keys away f rom liquids.
If they get wet, dry them
immediately with a sof t cloth.
The DX model keys do not contain
batteries. Do not try to take them
apart.
The master key fits all the locks on
your vehicle. The valet key works
only in the ignition and the door lock.
You can keep the trunk release
handle, rear seat trunk access, and
glove box locked when you leave
your vehicle and the valet key at a
parking f acility.
Keys and Locks
Inst rument s and Cont rols80
——y

y
(
yy

If the system repeatedly does not
recognize the coding of your key,
contact your Honda dealer.
Do not attempt to alter this system
or add other devices to it. Electrical
problems could result that may make
your vehicle undriveable.
If you have lost your key and you
cannot start the engine, contact a
Honda dealer.
The Immobilizer System protects
your vehicle f rom thef t. If an
improperly-coded key (or other
device) is used, the engine’s f uel
system is disabled.
When you turn the ignition switch to
ON (II), the Immobilizer System
indicator should come on f or a f ew
seconds, then go out. If the indicator
starts to blink, it means the system
does not recognize the coding of the
key. Turn the ignition switch to
LOCK (0), remove the key, reinsert
it, and turn the switch to ON (II)
again.
The system may not recognize your
key’s coding if another immobilizer
key or other metal object (i.e. key
f ob) is near the ignition switch when
you insert the key.As required by the FCC:
This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, including
interf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f or
compliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not cause
interf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
Immobilizer Syst em
Inst rument s and Cont rols81
——y

y
(
yy