HONDA ACCORD COUPE 2002 CL7 / 7.G Repair Manual

The engine can be severely damaged
if this light f lashes or stays on when
the engine is running. For complete
inf ormation, see page .
If this light comes on when the
engine is running, the battery is not
being charged. For complete
inf ormation, see page .
This indicator lights when you turn
the ignition switch ON (II). It is a
reminder to you and your passengers
to protect yourselves by f astening
the seat belts. A beeper also sounds
if you have not fastened your seat
belt.
If you do not f asten your seat belt,
the beeper will stop af ter a f ew
seconds but the light stays on until
you do. Both the light and the beeper
stay of f if you f asten your seat belt
bef ore turning on the ignition.
The instrument panel has many
indicators to give you important
inf ormation about your car.
327
328
Indicator L ights
Inst rument s and Cont rols
L ow Oil Pressure
Indicator
Charging System
Indicator
Seat Belt Reminder L ight
58

This indicator comes on f or a f ew
seconds when you turn the ignition
switch ON (II). It will then go of f if
you have inserted a properly-coded
ignition key. If it is not a properly-
coded key, the indicator will blink
and the engine will not start (see
page ).
This indicator also blinks several
times when you turn the ignition
switch f rom ON (II) to ACCESSORY
(I) or LOCK (0).
This light normally comes on f or a
f ew seconds when you turn the
ignition switch ON (II), and when
the ignition switch is turned to
START (III). If this light comes on at
any other time, there is a problem in
theABS.If thishappens,takethe
cartoyourdealertohaveitchecked.
With the light on, your car still has
normal braking ability but no anti-
lock. For complete inf ormation, see
page .
This light has two f unctions:
This indicator comes on when you
turn the ignition switch ON (II). It
is a reminder to check the parking
brake. Driving with the parking
brake not f ully released can
damage the brakes and tires.
If the indicator remains lit after
you have f ully released the
parking brake while the engine is
running, or if it comes on while
driving, it can indicate a problem
in the brake system. For complete
inf ormation, see page . See page .
1.
2.
75
332 219
329
Only on models equipped with ABS (see
page ) 200
Indicator L ights
Inst rument s and Cont rols
Immobilizer System
Indicator
Malf unction Indicator
Lamp
Anti-lock Brake System
(A BS) Indicator
Parking Brake and
Brake System Indicator
59
U.S. Canada
U.S. Canada

This indicator has three f unctions:Itcomesonasareminderthatyou
have turned off the Traction
Control System.
It f lashes when the TCS is
regulating wheelspin.
If itcomesonandstaysonwhen
the Traction Control System is on,
it indicates that there is a problem
in the TCS.
This light also comes on when you
turn the ignition ON (II) and goes off
af ter the engine starts. See page f or more inf ormation on the
TCS. This indicator lights when you turn
the ignition switch ON (II). If it
comes on at any other time, it
indicates a potential problem with
your f ront airbags or automatic seat
belt tensioners. On models equipped
with side airbags, this light will also
alert you to a potential problem with
your side airbags or passenger’s side
airbag automatic cut-off system. For
complete inf ormation, see page .
This indicator lights when you turn
the ignition switch ON (II). If it
comes on at any other time, it
indicates that the passenger’s side
airbag has automatically shut off.
For complete inf ormation, see page
.
1.
2.
3.
49
48
220
Only on models equipped with side airbags
On all V6 models
Supplemental Restraint
System Indicator
Traction Control System
(T CS) Indicator Side A irbag Cut-of f
Indicator
Indicator L ights
Inst rument s and Cont rols60

Canadian models only
This indicator lights when you turn
the ignition switch to ON (II) with
the headlight switch of f and the
parking brake set. It should go of f if
youturnontheheadlightsorrelease
the parking brake. If it comes on at
any other time, it means there is a
problem with the DRL. There may
also be a problem with the high
beam headlights.
The lef t or right turn signal light
blinks when you signal a lane change
or turn. If the light does not blink or
blinks rapidly, it usually means one
of the turn signal bulbs is burned out
(see page ). Replace the bulb as
soon as possible, since other drivers
cannot see that you are signalling.
A burned out brake light is a hazard
when drivers behind you cannot tell
you are braking. Have your brake
lights repaired right away. The appropriate light comes on in
this display if the trunk or either
door is not closed tightly. If a brake
light does not work, the indicator comes on when you
push the brake pedal with the
ignition switch ON (II).
All the lights in the monitor display
come on when you turn the ignition
switch ON (II). The lights go of f
af ter the engine starts and the trunk
and both doors are closed tightly. WhenyouturnontheHazard
Warning switch, both turn signal
lights blink. All turn signals on the
outside of the car should f lash.
292 ‘‘Daytime Running
Lights’’ Indicator
Turn Signal and
Hazard Warning
Indicators
Door and Brake L amp Monitor
Indicator L ights
Inst rument s and Cont rols61
BRAKE
LAMP

This light comes on when the
washer f luid level is low. Add washer
f luid when you see this light come on
(see page ).
On Canadian models, this indicator
comes on with reduced brightness
when the Daytime Running Lights
(DRL) are on (see page ).
This lights when you set the cruise
control. See page f or inf ormation
on operating the cruise control.
This light comes on as a reminder
that you must ref uel soon. This light comes on with the high
beam headlights. See page for
inf ormation on the headlight
controls. 67
68
181 260
Canadian models only
Washer Level Indicator
High Beam Indicator
Cruise Control Indicator
Low Fuel Indicator
Indicator L ights
Inst rument s and Cont rols62

This shows your speed in miles per
hour (mph). The smaller inner
numbers are the speed in kilometers
per hour (km/h).The tachometer shows the engine
speed in revolutions per minute
(rpm). To protect the engine f rom
damage, never drive with the
tachometer needle in the red zone.
The odometer shows the total dis-
tance your car has been driven. It
measures miles in U.S. models and
kilometers in Canadian models.
The total number is displayed when
you turn the ignition switch ON (II).
It is illegal under U.S. f ederal law and
Canadian provincial regulations to
disconnect, reset, or alter the
odometer with the intent to change
the number of miles or kilometers
indicated.
This shows your speed in kilometers
per hour (km/h). The smaller inner
numbers are the speed in miles per
hour (mph).
U.S. Models
Canadian Models
Speedometer T achometer
Odometer
Gauges
Inst rument s and Cont rols
U.S. Model shown
63
S SP
PE
EE
ED
D O
OM M E
ET
TE
ER
R
M
M A
AI
INNT TE
EN
NA AN
NC CEE
R
RE EQ
QU UIIRRE ED
D I
INND DI
ICCA A T
TO
OR R T
T
E
EM
M P
PE
ER
RA A T
TU
UR REE
G
GA AU
UG GEE
T
T
A
A C
CHH O
OM M E
ET
TE
ER
R F
FUUE EL
L G
GAAU
UG GEE
T
T R
RI IPP M
M E
ET
TE
ER
R S
SEEL
LEE C
CT T/
/R
RE ES
SE ET
T B
BUUT TT
TO
ON N
T
T
R
RI IPP M
M E
ET
TE
ER
R O
ODDO
OM M E
ET
TE
ER
R

4-cylinder models6-cylinder models
6-cylinder models
The gauge stays at the same f uel
level reading af ter you turn of f the
ignition. When you add f uel, the
gauge slowly changes to the new
readingafteryouturntheignition
switch back ON (II).
The needle returns to the bottom
after you turn off the ignition. The
gauge shows the f uel level reading
immediately af ter you turn the
ignition switch back ON (II). This shows how much f uel you have.
It is most accurate when the car is on
level ground. It may show slightly
more or less than the actual amount
whenyouaredrivingoncurvyor
hilly roads.
This meter shows the number of
miles (U.S.) or kilometers (Canada)
driven since you last reset it.
There are two trip meters: Trip A
and Trip B. Switch between these
displays by pressing the Select/
Reset button repeatedly. Each trip
meter works independently, so you
can keep track of two dif f erent
distances.
To reset a trip meter, display it, and
then press and hold the Select/Reset
button until the number resets to
‘‘0.0’’.
Both trip meters will reset if the car’s
battery goes dead or is disconnected. This shows the temperature of the
engine’s coolant. During normal
operation, the pointer should rise
from the bottom white mark to about
the middle of the gauge. In severe
driving conditions, such as very hot
weather or a long period of uphill
driving, the pointer may rise to near
the upper red mark. If it reaches the
red (Hot) mark, pull saf ely to the
side of the road. Turn to page f or
instructions and precautions on
checking the engine’s cooling
system.
324
Trip Meter
Temperature GaugeFuel Gauge
Gauges
Inst rument s and Cont rols64

Ref er to the Maintenance Schedules
f or Normal and Severe Driving
Conditions on pages and .
For the f irst 6,000 miles (9,600 km)
af ter the Maintenance Required
Indicator is reset, it will come on f or
two seconds when you turn the
ignition switch ON (II). This indicator reminds you that it is
time to take your car in for
scheduled maintenance.Between 6,000 miles (9,600 km) and
7,500 miles (12,000 km) this
indicator will light f or two seconds
when you first turn the ignition
switch ON (II), and then f lash f or
ten seconds.
If you exceed 7,500 miles (12,000
km) without having the scheduled
maintenance perf ormed, this
indicator will remain on as a constant
reminder.
Your dealer will reset this indicator
af ter completing the scheduled
maintenance. If this maintenance is
done by someone other than your
Honda dealer, reset the indicator as
f ollows.
Turn of f the engine. Press and hold the select/reset
buttonintheinstrumentpanel,
then turn the ignition switch ON
(II).
Hold the button until the indicator
resets (approximately ten
seconds).
1. 2.
3.
238 242
Maintenance Required Indicator
Gauges
Inst rument s and Cont rols65
M M
A
AI
INNT TE
EN
NA AN
NC CEE R
REEQ
QU UIIRRE ED
D
I
IN ND DI
ICCA A T
TO
OR R S
SE
EL
LEE C
CT T/
/R
RE ES
SE ET
T B
BUUT TT
TO
ON N

Î
Î
Î
Thetwoleversonthesteering
column contain controls f or driving
f eatures you use most of ten. The lef t
lever controls the turn signals,
headlights, and high beams. The
right lever controls the windshield
washers and wipers.
The tilt adjustment lever on the
underside of the steering column
allows you to tilt the steering wheel. The switches for the hazard warning
lights and rear window def ogger are
located to the right of the steering
column.To use the horn, press the pad
around the ‘‘H’’ logo.
The controls under the lef t air vent
are f or the moonroof , cruise control,
and the TCS.
:
Controls Near the Steering Wheel
Inst rument s and Cont rols66
H H A
AZ
ZA
A R
RDD W
WA AR
RNNI INNG G L
LIIGGH HT
TS
S
H
H
E
EA
A D
DL
LIIGGH HT
TS
S/ /
T
T U
UR RNN S
SIIGGN NAAL
LSS
M
M O
OOONNRROOO OFF
S
SW WI ITT C
CH H W
WI
INND DS
SHH I
IEE L
LDD
W
WI IPP E
ER
RS S//W
WA AS
SHH E
ER
RS S
T
T I
ILLT T A
AD
DJ
JUUS STTM
ME N
NTT
E
E X
X -
-V
V 6
6 m
m o
od
de
elli
iss s
shh o
ow
wn n.
. (
(
P
P .
.7700 ,
,771 1))
(
(
P
P .
.6677,, 6699) )
(
(P
P .
.7722 )
)
R
RE
EA
A R
R W
WI INND DO
OW W
D
D E
EF
FOOG GGGEER
R
(
( P
P .
.7711 )
)
C
CR
RUUI ISSE E
C
CO ON NTTR
RO OL L
M
M A
AS
STTE
ER
R
S
SW WI ITT C
CH H
R
REEM
M O
OTTE
E A
AU
UD DI
IOO
C
CO ON NTTR
RO OL LSS
H
HO
OR RNN
(
(
P
P .
.9966))
(
( P
P .
.7733 )
)
(
(
P
P .
.118811))
T
T
R
RA A C
CTTI
IOON N
C
CO ON NTTR
RO OL L
S
SY YSSTTE
EM
M O
ONN//
O
OF FFF S
SWWI ITT C
CH H
(
( O
On n V
V6
6 m
m o
od
de
ellss) )
(
( P
P .
.222200) )
(
(P
P .
.6666))
(
( O
On n E
EX
X a
ann d
d
E
E X
X -
-V
V 6
6 m
m o
od
de
ellss) )
(
(
P
P .
.118888) )

If you leave the lights on with the
ignition switch in ACCESSORY (I)
or LOCK (0), you will hear a
reminder chime when you open the
driver’s door.
The rotating switch on the lef t lever
controls the lights. Turning this
switch to the ‘‘ ’’ position turns
on the parking lights, taillights,
instrument panel lights, side-marker
lights, and rear license plate lights.
Turning the switch to the ‘‘ ’’
position turns on the headlights. To change between low beams and
high beams, pull the turn signal lever
until you hear a click, then let go.
The blue high beam indicator will
light (see page ).To f lash the high beams, pull the
turn signal lever back lightly, then
release it. The high beams will come
on and go of f .
The high beams will stay on f or as
long as you hold the lever back, no
matter what position the headlight
switch is in.
62
Headlights
Controls Near the Steering Wheel
Inst rument s and Cont rols67