window HONDA ACCORD HYBRID 2019 User Guide

133uu Indicators u Driver Information Interface Wa rning and Information Messages
Continued
Instrument Panel
Message Condition Explanation●
Appears if anything covers the radar sensor cover
and prevents the sensor fro m detecting a vehicle in
front. ●
May appear when driving in bad weather (rain,
snow, fog, etc.). ●
When the radar sensor gets dirty, stop your vehicle in a
safe place, and wipe off dirt using a soft cloth. ●
Have your vehicle checked by a dealer if the message
does not disappear even after you clean the sensor
cover. 2 Radar Sensor P. 570●
Appears if the temperature inside the front sensor
camera is too high and some driver assist systems
and auto high-beam cannot be activated. ●
Use the climate control sy stem to cool down the
camera. ●
Disappears - The camera has been cooled down and
the systems are activated normally. 2 Front Sensor Camera P. 568
2 Auto High-Beam P. 197●
Appears if the area around the front sensor camera is
blocked by dirt, mud, etc. and be prevented from
detecting a vehicle in front. ●
May appear when driving in bad weather (rain,
snow, fog, etc.). ●
When the front window gets dirty, stop your vehicle in
a safe place, and wipe it off with a soft cloth. ●
Have your vehicle checked by a dealer if the message
does not disappear even a fter you cleaned the area
around the camera. 2 Front Sensor Camera P. 568
2 Auto High-Beam P. 197

163Controls This chapter explains how to operate th e various controls necessary for driving.
Clock .................................................. 164
Locking and Unlocking the Doors
Key Types and Functions .................. 166
Low Remote Signal Strength ............ 168
Locking/Unlocking the Doors from the
Outside .......................................... 169
Locking/Unlocking the Doors from the
Inside ............................................. 176
Childproof Door Locks ..................... 178
Auto Door Locking/Unlocking .......... 179
Opening and Closing the Trunk ....... 180
Security System
Immobilizer System .......................... 183
Security System Alarm ...................... 184
Opening and Closing the Windows ..... 186 Opening and Closing the Moonroof *
..... 189
Operating the Switches Around the
Steering Wheel
ENGINE START/STOP Button............. 190
Turn Signals ..................................... 193
Light Switches.................................. 193
Fog Lights *
...................................... 195
Daytime Running Lights ................... 196
Auto High-Beam .............................. 197
Wipers and Washers ........................ 200
Rear Defogger/Heat ed Door Mirror *

Button ........................................... 202 Heated Windshield Button ............... 202
Brightness Control ........................... 203
Driving Position Memory System *
.... 205
Adjusting the Steering Wheel .......... 207
Adjusting the Mirrors
Interior Rearview Mirror ................... 208
Power Door Mirrors ......................... 209
Adjusting the Seats .......................... 210
Interior Lights/Interior Convenience
Items ................................................ 221
Climate Control System
Using Automatic Climate Control .... 239
Automatic Climate Control Sensors ... 242 Canadian models
* Not available on all models

uu Locking and Unlocking the Doors u Locking/Unlocking the Doors from the Outside
172
Controls To temporarily deactivate the function:
1. Set the power mode to OFF.
2. Open the driver’s door.
3. Using the master door lock switch, operate
the lock as follows:
Lock Unlock Lock Unlock.
u The beeper sounds and the function is
deactivated.
To restore the function:
• Set the power mode to ON.
• Lock the vehicle without using the auto lock
function.
• Walk away at least more than about 5 feet
(1.5 m) away from the vehicle while
carrying the remote.
• Open any door. 1 Locking the vehicle (Walk away auto lock ® )
The auto lock function does not operate when any of
the following conditions are met.
• The remote is inside the vehicle.
• A door or the hood is not closed.
• The power mode is set to any mode other than
OFF.
• The remote is not located within a radius of about
5 feet (1.5 m) from the ve hicle when you get out of
the vehicle and close the doors.
Auto lock function operation stop beeper
After the auto lock function has been activated, the
auto lock operation stop beeper sounds for
approximately two seconds in the following cases.
• The remote is put inside the vehicle through a
window.
• You are located too close to the vehicle.
• The remote is put inside the trunk.
If the warning beeper sounds, check that you are
carrying the remote. Then, open/close a door and
confirm the auto lock ac tivation beeper sounds once.
In the case that the remote is out of operating range
when you close a door or the trunk, a beeper will
sound to indicate that the auto lock function has
been canceled.

uu Locking and Unlocking the Doors u Childproof Door Locks
178
Controls Press the master door lock switch in (as
shown) to lock or unlock all the doors, fuel fill
door.
Childproof Door Locks The childproof door locks prevent the rear doors from being opened from the inside
regardless of the position of the lock tab.
Slide the lever in the rear door to the lock
position, and close the door.
■ When opening the door
Open the door using the outside door handle.■ Using the Master Door Lock Switch
To Unlock Master Door
Lock Switch
To Lock
■ Setting the Childproof Door Locks 1 Childproof Door Locks
To open the door from the inside when the
childproof door lock is on, put the lock tab in the
unlock position, lower the rear window, put your
hand out of the window, and pull the outside door
handle.
Unlock
Lock

184 uu Security System u Security System Alarm
Controls Security System Alarm The security system alarm activates when the trunk, hood or doors are forcibly
opened. The alarm does not activate if the trunk or doors are op ened with the key,
remote transmitter, or smart entr y with push button start system *
.
However, the alarm activates if a door is opened with the key and then the
transmission is taken out of ( P
(continuously variable transmission models) or the
hood is opened before the power mode is in ON.
■ When the security sy stem alarm activates
The horn sounds intermittently, and some the exterior lights flash.
■ To deactivate the security system alarm
Unlock the vehicle using the key, remote transmitter or smart entry with push
button start system *
. The system, along with the ho rn and flashing lights, is
deactivated.
■ Setting the security system alarm
The security system alarm automatically sets when th e following conditions have
been met:
• The power mode is set to VEHICLE OFF.
• The hood and trunk are closed.
• All doors are locked from outside with the key, remote transmitter, or smart entry
with push button start system *
.
■ When the security system alarm sets
The security system alarm indicator in the instrument panel blinks and the blinking
interval changes after about 15 seconds.
■ To cancel the security system alarm
The security system alarm is canceled when the vehicle is unlocked using the key *
,
remote transmitter or smart entry with push button start system *
, or when the power
mode is set to ON. The security system alarm indicator goes off at the same time. 1 Security System Alarm
Do not alter the system or add other devices to it.
Doing so may damage the system and make your
vehicle inoperable.
The security alarm continues for a maximum of two
minutes until the security system alarm deactivates.
Do not set the security system alarm when someone
is in the vehicle or a window is open. The system can
accidentally activate when:
• Unlocking the door with the lock tab.
• Opening the trunk with the trunk opener or the
emergency trunk opener.
• Opening the hood with the hood release.
• Taking the transmission out of ( P
.
If the battery goes dead after you have set the
security system alarm, the security alarm may go off
once the battery is re charged or replaced.
If this occurs, deactivate the security system alarm by
unlocking a door using the ke y, remote transmitter,
or smart entry with push button start system *
.Continuously variable transmission models
* Not available on all models

186
Controls Opening and Closing the WindowsOpening/Closing the Power Windows The power windows can be opened and cl osed when the power mode is in ON,
using the switches on the doors. The driver’s side switches can be used to open and
close all the windows.
The power window lock button on the driver’s side must be switched off (indicator
off) to open and close th e windows from anywhere othe r than the driver’s seat.
When the power window lock button is pressed, the indicator comes on and you
can only operate the driver’s window. Turn the power window lock button on
(indicator on) if a child is in the vehicle.
■ Manual operation
To open: Push the switch down lightly, and
hold it until the desired position is reached.
To close: Pull the switch up lightly, and hold it
until the desired position is reached.
■ Automatic operation
To open: Push the switch down firmly.
To close: Pull the switch up firmly.
The window opens or closes completely. To
stop the window at any time, push or pull the
switch briefly.■ Opening/Closing Windows with Auto-Open/Close Function 1 Opening/Closing the Power Windows
The power windows can be operated for up to 10
minutes after you set the power mode to VEHICLE
OFF.
Opening either front door cancels this function.
Auto Reverse
If a power window senses resistance when closing
automatically, it will stop closing and reverse
direction.
The driver’s window auto re verse function is disabled
when you continuously pull up the switch.
The auto reverse function stops sensing when the
window is almost closed to en sure that it fully closes.3
WARNING Closing a power window on someone’s
hands or fingers can cause serious injury.
Make sure your passengers are away from
the windows before closing them.
Power
Window
Lock Button
Indicator
Driver’s Window
Switch Front Passenger’s
Window Switch

187uu Opening and Closing the Windows u Opening/Closing the Power Windows
Continued
Controls
To open: Push the switch down.
To close: Pull the switch up.
Release the switch when the window reaches
the desired position.
To open: Press the unlock button, and then
within 10 seconds, press it again and hold it.
If the windows and moonroof *
stop midway,
repeat the procedure.■ Opening/Closing Windows without Auto-Open/Close Function Close
Open
■ Opening Windows and Moonroof *
with the Remote
Unlock
Button
* Not available on all models

188 uu Opening and Closing the Windows u Opening/Closing th e Power Windows
Controls To open: Unlock the driver’s door with the
key. Within 10 seconds of returning the key to
the central position, turn the key in the unlock
direction and hold it there.
To close: Lock the driver’s door with the key.
Within 10 seconds of returning the key to the
central position, turn the key in the lock
direction and hold it there.
Release the key to stop the windows/
moonroof *
at the desired position. If you want
further adjustment, repeat the same
operation.■ Opening/Closing the Windows and Moonroof *
with the KeyClose
Open
* Not available on all models

189
Controls
Opening and Closing the Moonroof *
You can only operate the moonroof when th e power mode is in ON. Use the switch
in the front of the ceiling to open and close the moonroof.
■ Automatic operation
To open: Pull the switch back firmly.
To close: Push the switch forward firmly.
The moonroof will automa tically open or close
all the way. To stop the moonroof midway,
pull or push the switch briefly.
■ Manual operation
To open: Pull the switch back lightly, and
hold it until the desired position is reached.
To close: Push the switch fo rward lightly, and
hold it until the desired position is reached.
■ Tilting the moonroof up
To tilt: Push on the center of the moonroof
switch.
To close: Push the switch forward firmly,
then release.■ Opening/Closing the Moonroof 1 Opening/Closing the Moonroof
NOTICE
Opening the moonroof in below freezing
temperature or when it is covered with snow or ice
can damage the moonr oof panel or motor.
The power moonroof can be operated for up to 10
minutes after you set the power mode to OFF.
Opening either front door cancels this function.
When resistance is detected, the auto reverse
function causes the moonroof to change directions,
then stop. Auto reverse stops sensing when the
moonroof is almost closed to ensure that it fully
closes. Make sure that al l objects, including fingers,
are clear of the moonroof.
You can use the remote transmitter or the key to
operate the moonroof.
2 Opening Windows and Moonroof *
with
the Remote P. 187
2 Opening/Closing the Windows and
Moonroof *
with the Key P. 1883
WARNING Opening or closing the moonroof on
someone’s hands or fingers can cause
serious injury.
Make sure all hands and fingers are clear of
the moonroof before opening or closing it.Open
Close Tilt
* Not available on all models

190
Controls Operating the Switches Around the Steering WheelENGINE START/STOP Button
*1 : Manual transmission models
*2 : Continuously variable transmi ssion models for Canadian models
*3 : U.S. models
*4 : Automatic transmission models■ Changing the Power Mode 1 ENGINE START/STOP Button
ENGINE START/STOP Button Operating Range
You can start the engine wh en the remote is inside
the vehicle.
If the battery of the remote is getting low, the engine
may not start when you push the ENGINE START/
STOP button. If the engine do es not start, refer to
the following link.
2 If the Remote Battery is Weak P. 672
The engine may also run if the remote is close to the
door or window, even if it is outside the vehicle.
ON mode:
The ENGINE START/STOP button is red when the
engine is running. Operating RangeContinuously Variable Transmission Automatic/Manual Transmission
VEHICLE OFF (LOCK)
The button is off.
The steering wheel is locked *1*2
.
The power to all electrical
components is turned off.
Press the button without the
transmission in ( P
.
Put the transmission into ( P

then press the button. Press the button. Without pressing the
clutch *1
or brake *4
pedalWithout pressing
the brake pedal ACCESSORY
The button blinks (in red).
Operate the audio system and
other accessories in this position.
ON
The button blinks (in red).
All electrical components can be
used.
Put the transmission into ( P *3
.*3