high beam HONDA ACCORD HYBRID 2023 Owners Manual

23
Quick Reference Guide
Controls (P 141)
Clock (P 142)
To adjust time
To adjust date
aSelect the (Home) icon, then select
General Settings.
bSelect System , then Date & Time .
cSelect Set Date & Time .
dSelect Automatic Date & Time , then
select Off.
eSelect Set Date or Set Time.
fAdjust the dates, hours, and minutes
by selecting / .
gSelect the (back) icon to set the
time.
34
5IF
DMPDL
JT
BVUPNBUJ DBMMZ
VQEBUFE
UISPVHI

UIF
BVEJP
TZTUFN
POWER Button (P 170)
Press the button to ch ange the vehicle’s
power mode.
Turn Signals (P 173)
Lights (P 174)
Turn Signal Control Lever
Light Control Switches
Low Beam High Beam
Flashing
* Not available on all models
23 ACCORD 4D US HEV MAP-3130B6000.book 23 ページ ２０２２年１０月１３日　木曜日 　午後４時５０分

91
uuIndicators u
Continued
Instrument Panel
*1 : When you set the power mode to ON, these indicators come on to indicate that system checks are being performed. They go off a few seconds later or after the power
system has started. If an indicator does not come on or turn off, there may be a malfunction in the corresponding system. To re solve the issue, follow the instructions in
the owner’s manual.
Auto High-Beam
Indicator
Low Tire Pressure/
TPMS Indicator*
Turn Signal and
Hazard Warning
Indicators
Lights On
Indicator
High Beam
Indicator
System Message
Indicator Adaptive Cruise Control
(ACC) with Low Speed
Follow Indicator (Amber)
Lane Keeping Assist
System (LKAS) Indicator
(Amber)
Safety Support
Indicator (Green/Gray)

P. 100
CHARGE Mode
Indica

tor
P. 103

P.

101 
P. 10 4
*1

P. 101
 P. 101

P. 101 Immobilizer System
Indicator

P. 103
S

ecu
rity System Alarm
Indicator 
P. 103
 P. 102 
P. 105
 P. 109
*1
Adaptive Cruise Control
(ACC) with Low Speed
Follow Indicator
(White/Green)
 P. 104
*1
Lane Keeping Assist
System (LKAS) Indicator
(White/Green) 
P. 105
*1Safety Support
Indicator (Amber) 
P. 106
*1
NORMAL Mode
Indicator 
P. 102
AUTO Mode Indicator
 P. 103
EV Mode Indicator  P. 103
SPORT


Mode Indic

ator
P. 102
Cruise Mode Indicator
(White/Green) 
P. 105
Adaptive Cruise Control
(ACC) with Low Speed
Follow Interv al Indicator
P. 105
ECON Mode Indicator
 P. 102 INDIVIDUAL
Mode
Indicator 
P.

102
* Not available on all models
23 ACCORD 4D US HEV MAP-3130B6000.book 91 ページ ２０２２年１０月１３日　木曜日 　午後４時５０分

101
uuIndicators u
Continued
Instrument Panel
IndicatorNameOn/BlinkingExplanation
Turn Signal and
Hazard Warning
Indicators•Blinks when you operate the turn signal
lever.
• Blinks along with all turn signals when you
press the hazard warning button.●Does not blink or blinks rapidly - Have your
vehicle checked by a dealer.
Lights On Indicator• Comes on when the parking, tail, and
other external lights are on.2 Light Switches P. 174
High Beam
Indicator•Comes on when the high beam headlights
are on.—
Auto High-Beam
Indicator•Comes on when all the operating
conditions of the auto high-beam are met.2 Auto High-Beam P. 178
23 ACCORD 4D US HEV MAP-3130B6000.book 101 ページ ２０２２年１０月１３日　木曜日　午後４時５０分

141
Controls
This chapter explains how to operate the various controls necessary for driving.
Clock.................................................. 142
Locking and Unlocking the Doors Key .................................................. 144
Low Keyless Remote Signal Strength ... 145
Locking/Unlocking the Doors from the Outside .......................................... 146
Locking/Unlocking the Doors from the Inside ............................................. 155
Childproof Door Locks ..................... 157
Auto Door Locking/Unlocking .......... 158
Opening and Closing the Trunk ....... 159
Security System
Immobilizer System .......................... 162 Security System Alarm...................... 162
Windows ........................................... 165
Moonroof .......................................... 168
Operating the Switches Around the Steering Wheel POWER Button................................. 170
Turn Signals ..................................... 173
Light Switches.................................. 174
Daytime Running Lights ................... 177
Auto High-Beam .............................. 178
Wipers and Washers ........................ 181
Rear Defogger/Heat ed Door Mirror
*
Button ........................................... 183 Driving Position Memory System
*.... 184
Adjusting the Steering Wheel .......... 186
Mirrors
Interior Rearview Mirror ................... 187
Power Door Mirrors ......................... 188
Seats .................................................. 189
Interior Convenience Items .............. 198
Climate Control System Using Automatic Climate Control .... 214
Automatic Climate Control Sensors ... 218
* Not available on all models
23 ACCORD 4D US HEV MAP-3130B6000.book 141 ページ ２０２２年１０月１３日　木曜日　午後４時５０分

174
uuOperating the Switches Around the Steering Wheel uLight Switches
Controls
Light Switches
Rotating the light switch turns the lights on
and off, regardless of the power mode
setting.
■High beams
Push the lever forward until you hear a click.
■Low beams
When in high beams, pull the lever back to
return to low beams.
■Flashing the high beams
Pull the lever back, and release it.
■Lights off
Turn the lever to OFF either when:
• The transmission is in
(P.
• The parking brake is applied.
To turn the lights on ag ain, turn the lever to
OFF to cancel the lights off mode. Even if you
do not cancel the lights off mode, the lights
come on automatically when:
• The transmission is taken out of
(P and the
parking brake is released.
• The vehicle starts to move.
■Manual Operation1Light Switches
If you leave the power mode in VEHICLE OFF while
the lights are on, a chime sounds when the driver’s
door is opened.
When the lights are on, the lights on indicator in the
instrument pane l will be on.
2 Indicators P. 90
If you sense that the le vel of the headlights is
abnormal, have the vehicl e inspected by a dealer.
Do not leave the lights on when the power system is
off because it will caus e the 12-volt battery to
discharge.
Turns on parking, side marker,
tail, and rear license plate light
Turns on headlights, parking,
side marker, tail, and rear license
plate light
High Beams
Flashing the high beams
Low Beams
23 ACCORD 4D US HEV MAP-3130B6000.book 174 ページ ２０２２年１０月１３日　木曜日　午後４時５０分

178
uuOperating the Switches Around the Steering Wheel uAuto High-Beam
Controls
Auto High-Beam
The front sensor camera detects the light sources ahead of the vehicle such as the
lights of a preceding or oncoming vehicle, or street lights. When you are driving at
night, the system automatically switches the headlights between low beam and high
beam depending on the situation.
■Activating the system
When all of the following conditions have been met, the auto high-beam indicator
comes on and between the high beam and low beam switches automatically
depending on the situation. •The power mode is in ON.
• The light switch is in AUTO.
• The lever is in the low beam position.
• The headlights have been automatically
activated.
• It is dark outside the vehicle.
If the auto high-beam indicator does not co me on even when all the conditions have
been met, carry out either of the procedur es below and the indicator will come on.
• Pull the lever toward you and release it.
• Turn the light switch to th en turn the light switch to AUTO.
■How to Use the Auto High-Beam
1Auto High-Beam
The auto high-beam system does not always operate
in every situation. This syst em is just for assisting the
driver. Always observe your surroundings and switch
the headlights between high beam and low beam
manually if necessary.
If you find the timing of beam changes inconvenient
for driving, change the headlight beams manually.
The range and the distance at which the camera can
recognize varies de pending on conditions
surrounding your vehicle.
Regarding the handling of the camera mounted to
the inside of the windshiel d, refer to the following.
2 Front Sensor Camera P. 479
For the auto high-beam to work properly:
•Do not place an object that reflects light on the
dashboard.
•Keep the windshield around the camera clean.
•When cleaning the windshield, be careful not to
apply the windshield cleans er to the camera lens.
•Do not attach an object, sticker, or film to the area
around the camera.
•Do not touch the camera lens.
If the camera receives a st rong impact, or repairing of
the area near the camera is required, consult a dealer.
Light Switch
Auto High-Beam
Indicator
23 ACCORD 4D US HEV MAP-3130B6000.book 178 ページ ２０２２年１０月１３日　木曜日　午後４時５０分

Continued179
uuOperating the Switches Around the Steering Wheel uAuto High-Beam
Controls
■Automatic switching between high-beam and low-beam
When the auto-high beam indicator comes on, the headlights switch between high
beam and low beam based on the following conditions.1 How to Use the Auto High-Beam
In the following cases, th e auto high-beam system
may not switch the head lights properly or the
switching timing may be ch anged. If the automatic
switching operation does not fit your driving habits,
please switch the headlights manually.
•The brightness of the ligh ts from a preceding or
oncoming vehicle is intense or poor.
•Visibility is poor due to the weather (rain, snow,
fog, windshield frost, etc.).
•Surrounding light sources like street lights, electric
billboards, and tr affic lights are illuminating the
road ahead.
•The brightness level of th e road ahead constantly
changes.
•The road is bumpy or has many curves.•A vehicle suddenly appears in front of you, or a
vehicle in front of you is not in the preceding or
oncoming direction.
•Your vehicle is tilted with a heavy load in the rear.•A traffic sign, mirror, or other reflective object
ahead is reflecting strong light toward the vehicle.
•The oncoming vehicle freq uently disappears under
roadside trees or be hind median barriers.
•The preceding or oncoming vehicle is a motorcycle,
bicycle, mobility scooter, or other small vehicle.
The auto high-beam system keeps the headlight low
beam when:
•Windshield wipers are op erating at a high speed.
•The camera has detected a dense fog.
High beam
All of the following conditions must
be met before the high beams turn
on.
●Your vehicle speed is 25 mph (40
km/h) or more.
●There are no preceding or
oncoming vehicles with
headlights or taillights turned on.
●There are few street lights on the
road ahead.
Low beam
One of the following conditions
must be met before the low beams
turn on.
●Your vehicle speed is 15 mph (24
km/h) or less.
●There is a preceding or oncoming
vehicle with headlights or
taillights turned on.
●There are many street lights on
the road ahead.
23 ACCORD 4D US HEV MAP-3130B6000.book 179 ページ ２０２２年１０月１３日　木曜日　午後４時５０分

uuOperating the Switches Around the Steering Wheel uAuto High-Beam
180
Controls
■Manual switching between high-beam and low-beam
If you want to manually switch the headlights between high beam and low beam,
follow either of the proced ures below. Note that when you do this, the auto high-
beam indicator will turn off and the auto high-beam will be deactivated.
Using the lever:
Pull the lever toward you for flashi ng the high beams then release it.
u To reactivate the auto high-beam, follo w either of the procedures below and
the auto high-beam indicator will come on.
• Pull the lever towards you and release it.
• Turn the light switch to and then to AUTO when the lever is in the low beam
position.
Using the light switch:
Turn the light switch to . u To reactivate the auto high-be am, turn the light switch to AUTO when the
lever is in the low beam position, and the auto high-beam indicator will come
on.1 How to Use the Auto High-Beam
How to turn off the Auto High-Beam System
You can turn the auto high- beam system on and off.
2 Customized Features P. 318
If the Some driver assist systems cannot operate:
Camera temperature too high message appears:
•Use the climate control system to cool down the
interior and, if necessary, also use defroster mode
with the airflow directed toward the camera.
•Start driving the vehicle to lower the windshield
temperature, which cool s down the area around
the camera.
If the Some driver assist systems cannot operate:
Clean front windshield or poor viewing
condition. message appears:
•Park your vehicle in a safe place, and make sure the
windshield is clean.
Clean the windshield if it is dirty. If the message
does not disappear after dr iven for a while, have
your vehicle checked by a dealer.
23 ACCORD 4D US HEV MAP-3130B6000.book 180 ページ ２０２２年１０月１３日　木曜日　午後４時５０分

334
uuCustomized Features u
Features
■Lighting Setup
*1:Default Setting
Customizable Features DescriptionSelectable Settings
Auto High-BeamTurns the auto high-beam on and off.On*1/Off
Interior Light Dimming Time Selects the length of time the inte
rior lights stay on after doors are
closed.
2 Interior Lights P. 198
60sec/30sec*1/15sec
Headlight Auto Off Timer
Selects the length of time the exterior lights stay on after you close
the driver's door.
2 Automatic Lighting Off Feature P. 176
60sec/30sec /15sec*1/0sec
Auto Light Sensitivity
*Changes the timing for the headlights to come on. Max/High/ Mid*1/Low /Min
Auto Headlight On with
Wiper OnTurns headlight function at wi per operation On/Off when the
headlight is in AUTO setting.
2Headlight Integration with Wipers P. 176
On*1/Off
* Not available on all models
23 ACCORD 4D US HEV MAP-3130B6000.book 334 ページ ２０２２年１０月１３日　木曜日　午後４時５０分

476
uuHonda Sensing ®u Traffic Sign Recognition System
Driving
■The position or the cond ition of the traffic sign
• The sign is in a place that makes it hard to find.
• The sign is located far away from your vehicle.
• The sign is located where it is hard for headlight beams to reach.
• The sign is on a corner or bend in the road.
• The sign is faded or bent.
• The sign is rotated or damaged.
• The sign is covered with mud, snow, or frost.
• Part of the sign is hidden by the trees, or is in the shadow of a vehicle or other
object.
• Light (such as a streetlight) is reflected on the surface of the sign, or it is hidden
in shadow.
• The sign is too bright or too dark (electric signs).
• Small signs (auxiliary signs, etc.).
■Other conditions
• When you are driving at a high speed.
23 ACCORD 4D US HEV MAP-3130B6000.book 476 ページ ２０２２年１０月１３日　木曜日　午後４時５０分