radiator HONDA ACCORD SEDAN 2001 Owner's Manual (in English)

Safety Labels

These labels are in the locations shown. They warn you of potential
hazards that could cause serious
injury. Read these labels carefully.
If a label comes off or becomes hard
to read, contact your Honda dealer
for a replacement.

Driver and Passenger Safety

DASH BOARD

SUN VISOR

U.S. models

RADIATOR CAP

HOOD
Canadian models
U.S. models only

Service Station Procedures

4. Remove the dipstick again and check the level. It should be
between the upper and lower marks.
If it is near or below the lower mark,
see Adding Oil on page 234 . Engine Coolant Check
Look at the coolant level in the
radiator reserve tank. Make sure it is
between the MAX and MIN lines. If it is below the MIN line, see Adding
Engine Coolant on page 239 for
information on adding the proper

coolant.
Refer to Owner Maintenance
Checks on page 231 for information
on checking other items in your

Honda.

Before Driving
UPPER MARK
LOWER MARK
MAX

RESERVE TANK

MIN

4-cylinder models RESERVE TANK

6-cylinder models
MIN
MAX

Owner Maintenance Checks
You should check the following items at the specified intervals. If
you are unsure of how to perform any check, turn to the page given. Engine oil level — Check every
time you fill the fuel tank. See
page 182. Engine coolant level — Check the
radiator reserve tank every time
you fill the fuel tank. See page 184 .
Windshield washer fluid — Check
the level in the reservoir monthly.If weather conditions cause you to
use the washers frequently, check
the reservoir each time you stop
for fuel. See page 246 . Automatic transmission — Check
the fluid level monthly. See page 247. Brakes — Check the fluid level

monthly. See page 251.
Tires — Check the tire pressure
monthly. Examine the tread for
wear and foreign objects. See page
267.
Lights — Check the operation of
the headlights, parking lights,
taillights, high-mount brake light,
turn signals, brake lights, and
license plate lights monthly. See

page 274.

Maintenance

Fluid Locations

Maintenance

4-cylinder Models

BRAKE FLUID(Gray cap)
ENGINE OIL
FILL CAP

AUTOMATIC

TRANSMISSION
FLUID DIPSTICK
(Yellow loop)

COOLANT

RESERVOIR
CLUTCH FLUID

(5-speed Manual

Transmission only)
(Gray cap)
ENGINE OIL DIPSTICK
(Orange loop)

WASHER FLUID (Blue cap)
POWER STEERING
FLUID (Red cap)
RADIATOR CAP

Fluid Locations

Maintenance

RADIATOR CAP
COOLANT

RESERVOIR

AUTOMATIC

TRANSMISSION

FLUID DIPSTICK

(Yellow loop)

6-cylinder Models

ENGINE OILFILL CAP
ENGINE OIL DIPSTICK

(Orange loop)

WASHER FLUID (Blue cap) BRAKE FLUID
(Gray cap)
POWER STEERING
FLUID (Red cap)

Cooling System

Adding Engine Coolant
If the coolant level in the reserve
tank is at or below the MIN line, add
coolant to bring it up to the MAX line.
Inspect the cooling system for leaks.
This coolant should always be a mixture of 50 percent antifreeze and50 percent water. Never add straight
antifreeze or plain water. Always use Genuine Honda All
Season Antifreeze/Coolant Type 2.
This coolant is pre-mixed with 50 percent antifreeze and 50 percent
water. It does not require anyadditional mixing. If it is not available,
you may use another major-brand non-silicate coolant as a temporary
replacement. Make sure it is a high-quality coolant recommended for
aluminum engines. However,
continued use of any non-Honda coolant can result in corrosion,
causing the cooling system to malfunction or fail. Have the cooling
system flushed and refilled with
Honda antifreeze/coolant as soon as

possible.

If the reserve tank is completely
empty, you should also check the
coolant level in the radiator.
CONTINUED
Maintenance
4-cylinder models

RESERVE TANK
RESERVE TANK

6-cylinder models

Cooling System

1. Make sure the engine and radiator
are cool.

2. Turn the radiator cap counter- clockwise, without pressing down
on it, until it stops. This relieves
any pressure remaining in the
cooling system.
3. Remove the radiator cap by
pushing down and turning

counterclockwise.

4. The coolant level should be up to the base of the filler neck. Add
coolant if it is low.
5. Put the radiator cap back on. Tighten it fully.
Maintenance
RADIATOR CAP

4-cylinder models 6-cylinder models

RADIATOR CAP
Removing the radiator cap
while the engine is hot can cause the coolant to spray out,
seriously scalding you.
Always let the engine and radiator cool down before
removing the radiator cap.

Cooling System

1. Open the hood. Make sure the engine and radiator are cool to the

touch.

Except EX- V6 model

Turn the ignition ON (II). Turn the temperature control Dial all
the way clockwise. Turn off theignition and remove the key.
EX-V6 model

Turn the ignition ON (II). Turn the temperature control dial to90°F (32° C). Turn off the ignition
and remove the key.
2. Remove the radiator cap.
4-cylinder models

3. Loosen the drain plug on the bottom of the radiator. Thecoolant will drain through the
splash guard. Remove the drain
bolt and washer from the engine
block.

Maintenance
DRAIN

BOLT

DRAIN

PLUG

6-cylinder models
4-cylinder models

4-cylinder models

Cooling System

6-cylinder models

3. Loosen the drain plug on the
bottom of the radiator. The
coolant will drain through the
splash guard. Loosen the drain
bolt. 4. Remove the reserve tank from its
holder by pulling it straight up.Drain the coolant, then put the
tank back in its holder. 6-cylinder models
When removing the reserve tank, first remove the cruise control cableand the ground cable from their clips.
After installing the tank back in place, put the cables back in their

clips.

CONTINUED

Maintenance
DRAIN PLUG
RESERVE TANKRESERVE TANK CAP

HOLDER

DRAIN BOLT
4-cylinder models
6-cylinder models
6-cylinder models

Cooling System

5. When the coolant stops draining, tighten the drain plug at the
bottom of the radiator.

6. 4-cylinder models
Put a new washer on the drain bolt,
then reinstall the drain bolt in the
engine block. Tighten it securely.
Tightening torque:
61 Ibf.ft (83 N.m , 8.5 kgf.m)
6-cylinder models

Tighten the drain bolt at the rear of the engine cylinder block
securely.

Tightening torque:
7 Ibf.ft (10 N.m, 1.0 kgf.m)
7. 4-cylinder models

Loosen the bleeder bolt on top of
the engine.
Pour Honda All Season
Antifreeze/Coolant Type 2 into the radiator. This coolant is a
mixture of 50 percent anti-freezeand 50 percent water. Pre-mixing
is not required.
Tighten the bleeder bolt when coolant comes out in a steadystream with no bubbles.

Maintenance

RESERVE TANK
RESERVE TANK CAP
HOLDER

6-cylinder models 4-cylinder models

Fill up to here
FILLER NECK
FILLER NECK
Fill up to here

6-cylinder models