fuses HONDA CIVIC 1998 6.G Owner's Manual

License Lights, Parking Lights, and Taillights
- Coupe, Sedan, and Hatchback
I I rusecs I
Li5:_i
"^1,1fr!;?'
arr*
HI
UNDER.DASHFUSE/RELAYBOX
UNDER.HOOOFUSE/RELAYBOX
g€o Pow€rDlstrbutiofl,page 101?.
B1 YFED/GFN ll-- -
:t! - - - '--:gsg-l 3totur['JY3;tttu vehicres pre'wired tor
: -i::-- - - -. c;A (oPrroN) ceucssu'Yir
neoionlr lf C422 | Ptloro 56I PHorc 587 A, vtEw t6
-)' 56€. Hsadlqht I
FUsEsr lYi-"'l;-. I
:]% ropnor.rt cLlEssv'v .evu"rt JtJre"'
ru9c ltz DaO€ 10$1.uclrlaEtlclllS -
ta{- uotfls7.lla
c927 13 Y CssloPTfoN I ltlglo 63
clNl.rEcroR I
-" "'
tFEoiEL( |
II
v
To Daoe 110-3(AliC6upes and '96- 98 Sedans),or page 1 10-4 ( 99- 00 Sedans),or page 110-5 (Halchback)
FED/8LK
1(with cruise 3)
RED/BLI(
GAN/YEI
AED/ELX'99100
moqelsc202r -'! wiiri| | xtYess
I I EntryI
KEYLESS '
DOORLOCK :CONTROL ;UNIT
RIGHT FRONTPARKING/TURNSIGNAL LIGHT
L.-r
/-1M LEFT FRONTfb d I PARKTNGIuRN
\Y,Z slcNAL LlcHr
'I
see Ground
"* | 3$l''Tll
II
l.?'J
! czoz- PHOfa 19
110-2

Headlights (cont'd)
- How the Circuit Works
Low Beams
With the headlight switch in HEAD and the dimmer
switch in LO, current tlows through the headlight
switch. fuse 21 . fuse 22. and the low beam
tilaments to ground, and the low beams come on.
High Beams
With the headlight switch in HEAD and the dimmer
switch in Hl, current flows through the headlight
switch, dimmer switch, fuses 4, 5, and the high
beam filaments to ground, and the high beams
come on.
Current also llows through the high beam indicator
light to ground. The high beam indicator comes on
to remind the driver that the high beams are on.
Flash-to-Pass
The flash feature works with the headlight switch in
OFF, PARK, or HEAD (low beams). When you move
the flash-to-pass switch to ON, current flows
through the switch, fuses 4 and 5, and the high
beam filaments to ground, and the high beams
flash. The high beam indicator also flashes during
the flash operation. The flash function has no effect
if the high beams are already on
Daytime Running Lights (Canada)
When you turn the ignition to ON (ll) with the
parking brake released, the daytime running lights
control unit supplies battery voltage at the
WHT/RED wire. This voltage is applied to the high
beam headlights through the daytime running lights
resistor. Each high beam headlight receives less
than battery voltage causing them to come on at
reduced brightness.
lf the parking brake is set, a ground signal is applied
to the daytime running lights control unit at the
RED/GRN wire. lf the parking brake is set when you
first turn the ignition switch to ON (ll), the high beam
headlights will remain off until you release the
parking brake. Once the high beam headlights are
on, setting the parking brake will not turn them ofi.
When low or high beam operation is requested,
battery voltage from the headlight switch is applied
to the daytime running light control unit via the RED
wire. The daytime running lights control unit then
turns off the headlights.
Refer to the Service Manual (Section 23, Electrical)
for specific tests or lroubleshootrng procedures.
110-14

\
Hatchback
FUSEs2 IltOn||.gTO? LT1laSBe PowerDbtribution,page 1G13.
S€e Powor
BRAKE SWITCHClos€d with brakepedal depressed.PHOTO 6A
UNDER.HOODFUSE/RELAYBOX
**TT**TI
BRAKE SWITCH I-I-TClosed w{h brake | | |
ffid"o'""""0 tld
*-."11
rr.l
.l I
ll-r I
*"*rtrl
"""^,"rf,
\,,r=Male-Female
termanals reversedlor '99-'00 models
c607
c60s
vtEw I
HIGH MOUNTBRAKE LIGHT
c608
@
".i.I
>-ra
BLK
2
BLK
\
+ g?o'1"'
110-17

Power Door Locks (cont'd)
Keyless Entry Does Not Work In Any
Mode
NOTE: Before beginning, verify that all the
transmitters are programmed to the vehicle.
1 . Does the radio work properly?
Yes - Go to step 9.
No - Go to the neld step.
NOTE: For steos 2 - 8. refer to the schematic dia-
gram for the Stereo Sound System on page 150.
2. Are fuses 28 (in the under-dash fuse box) and
fuse 47 (in the under-hood fuse box) OK?
Yes - Go to step 4.
No - Replace the blown fuse, then go to the
nen steo.
3. Does the fuse blow again?
Yes - Locate and repair the short.
No- Retest the system.
4. ls the vehicle equipped with the optional security
system?
Yes - Go to the next steP.
No - Go to steD 6.
5. Does the keyless entry work correctly when the
security control unit connector is disconnected?
Yes - Faulty security system, go to security
system for f urther troubleshooting.
No - Go to the next step.
6. ls there battery voltage at terminal 4 of the radio
main harness connector (A)?
7.
=A
Yes - Go to the nen step.
No - Locate the open in the wiring between
tuse 47 and the radio.
ls there battery voltage at terminal 5 of the radio
main harness connector (A), when the ignition
switch is in the ACC (l) or ON (ll) position?
Yes - Go to the next step.
No - Locate the open in the wiring between
fuse 28 and the radio.
130-8
8. ls there continuity from terminal 14 of the radio
main harness connector (A) to ground?
Yes - Replace the radio.
No - Repair the open in the wiring between the
radio and the ground (G501).
9. Does the transmitter LED come on when any ot
the buttons are oressed?
Yes - Go to steo 12.
No - Go to the next steo.'10.ls the transmitter battery installed with the
positive side facing up?
Yes - Ensure that the battery contact tabs are
repositioned, then replace the battery.
Remove the key from the ignition, then
close the doors and trunk. Press the
LOCK button on the transmitter six times,
then go to the next step.
No - Ensure that the baftery contact tabs are
repositioned, then reinstall the batlery
correctly. Then reprogram the transmitter
and retest it. Use the procedure on page
1 30-4 f or transmitter programming.
11 . Does the transmitter LED come on when any of
the buttons are oressed?
Yes - Go to the next step.
No - Replace the transmitter and program it by
using the procedure on page 130-4.
12.Does the system work properly in all modes?
Yes - Finished. The system is OK.
No - Go to the next steD.