crankshaft HONDA CIVIC 1999 6.G User Guide

HONDA CIVIC 1999 6.G User Guide CIVIC 1999 6.G HONDA HONDA https://www.carmanualsonline.info/img/13/6068/w960_6068-0.png HONDA CIVIC 1999 6.G User Guide

Page 132 of 2189

HONDA CIVIC 1999 6.G User Guide 3. Install the timing belt tightly in the sequence shown
OTiming belt drive pullev (crankshaft) )@Adjusting
pulley -towater pump pulley J@Camshatt pulley
NOTE: Make sure the timing belt drive pulley

Page 133 of 2189

HONDA CIVIC 1999 6.G User Guide Crankshaft Speed Fluctuation (CKF) Sensor
2.
3.
5.
Replacement
4.
1.
6x1.0mm12 N.m {1.2 kgt.m,8.7 tbf.ft)
6. Installthe CKF sensor in reverse order of removal.
Remove the cylinder head cover.
NOTE: R

Page 138 of 2189

HONDA CIVIC 1999 6.G User Guide Removal
Engine removal is not required for this procedure
!!!s@ Make sure iacks and salety stands are
f ta"eata"ea propetty and hoist brackets are attached to the
correct positions on the engine.
CAUT

Page 156 of 2189

HONDA CIVIC 1999 6.G User Guide Cylinder Head
4. Apply liquid gasket (Part No. 08718 - 0001 or 08718 -
0003) to the head mating surfaces of the No. 1 and
No.5 camshaft holders.- Apply liquid gasket to the shaded areas
Set the rocker

Page 159 of 2189

HONDA CIVIC 1999 6.G User Guide Gylinder Head/Valve Train
816A2 engine
Special Tools ............. 650 Rocker Arms
VTEC Contlol System
Troubfeshooting Flowchart ............ 6-51 Disassembly/Reassembly ...............672
VTEC Sole

Page 167 of 2189

HONDA CIVIC 1999 6.G User Guide Valve Glearance
Adjustment
NOTE:
. Valves should be adjusted only when the cylinder
head temperaturs is less than 100F (38C)
. After adjusting, retorque the crankshaft pulley bolt to
177 N.m (18.0

Page 168 of 2189

HONDA CIVIC 1999 6.G User Guide Valve Clearance
I
I
I
Adjustment {contd)
5. Tighten the locknut and recheck clearance.Repeat adjustment if necessary.
Rotate the crankshaft 180. counterclockwise(camshaft pulley turns 90). The "Up"

Page 169 of 2189

HONDA CIVIC 1999 6.G User Guide Crankshaft PulleY and PulleY Bolt
Replacement
When installing and tightening the pulley, follow the procedure below
Clean, remove any oil, and lubricate points shown below
a: Cleanx : Bemove anY oll

Page 170 of 2189

HONDA CIVIC 1999 6.G User Guide Timing Belt
lllustrated Index
NOTE:
. Refer to page 6-59 for positioning crankshaft and pulley before installing belt.. Mark the direction of rotation on the belt before removino.a Do not use the midd

Page 171 of 2189

HONDA CIVIC 1999 6.G User Guide Inspection
Remove the cylinder head cover.
NOTE: Refer to page 6-86 when installing the cylin-
der head cover.
Inspect the timing belt for cracks and oil or coolant
soakrng.
NOTE:
. Replace the belt i
Page:   < prev 1-10 11-20 21-30 31-40 41-50 51-60 ... 90 next >