HONDA CIVIC 1999 6.G Workshop Manual

HONDA CIVIC 1999 6.G Workshop Manual CIVIC 1999 6.G HONDA HONDA https://www.carmanualsonline.info/img/13/6068/w960_6068-0.png HONDA CIVIC 1999 6.G Workshop Manual
Trending: rear seal, 7-11, engine fan, Crank bearing, Cam cap, Ac thermos, Air condition

Page 851 of 2189

HONDA CIVIC 1999 6.G Workshop Manual Countershaft Bearing Replacement
1. Remove the countershaft bearing using the special
tools as snown.
3,/8.16 SLIDE HAMMER{Commerciallv available)
AOJUSTABLEBEARINGPULLER,25-{Omm07736 - A0�1000A
2.

Page 852 of 2189

HONDA CIVIC 1999 6.G Workshop Manual Transmission Housing Bearings
L
Mainshaft/Countershaft Bearings Replacement
To remove the mainshaft and countershaft bearings
from the transmission housing, expand each snap
ring with snap ring pliers

Page 853 of 2189

HONDA CIVIC 1999 6.G Workshop Manual Reverse ldler GearPark Stop
lnstallation
1, lnstall the reverse idler gear.
Install the reverse idler gear shaft holder and needle
bearing into the transmission housing, then tighten
the bolts.
6 x 1.

Page 854 of 2189

HONDA CIVIC 1999 6.G Workshop Manual Transmission
Reasembly
NOTE;
. Coat all parts with ATF.. Beplace the following parts:- O-rings- Lock washers- Gaskets- Mainshaft and countershaft locknuts and conical spring washers- Sealing washers
T

Page 855 of 2189

HONDA CIVIC 1999 6.G Workshop Manual 1.Install the ATF magnet and suction pipe collar in the
torque converter housing. if necessary.
lnstall the main seDarator plate and the two dowel
pins on the torque converter housang.
Install the ATF

Page 856 of 2189

HONDA CIVIC 1999 6.G Workshop Manual Transmission
_\,]ffil
Reassembly (contd)
TRANSMISSIONHANGER
MAINSHAFTSUB.ASSEMBLY
*
Ufln
$*U ./
TRANSMISSION HOUSINGMOUNTING BOLTS10 x 1.25 mm4{ N.m {4.5 kg{.m,33 lbI.ft)
TRANSMISSION HOUSING
REVER

Page 857 of 2189

HONDA CIVIC 1999 6.G Workshop Manual 17.
18.
19.
lnstall the reverse idler gear and the gear shaft
holder (see page 14-175).
lnstall the differential assembly in the torque con-
verter housing.
Assemble the mainshaft sub-assembly and the

Page 858 of 2189

HONDA CIVIC 1999 6.G Workshop Manual Transmission
26. Slip the special tool onto the mainshaft as shown,
MAINSHAFT HOLDER07GAB - PF50101
Installthe park lever on the control shaft.
Assemble the one-way clutch and the park gearwith the co

Page 859 of 2189

HONDA CIVIC 1999 6.G Workshop Manual 36. Remove the special tool from mainshaft, then stake
each locknut using a 3.5 mm punch as shown
COUNTERSHAFTLOCKNUT
Set the park lever in the El position, then verify that
the park Pawl engages the

Page 860 of 2189

HONDA CIVIC 1999 6.G Workshop Manual Torque Converter/Drive plate
6x1.0mm12 N.m (1.2 kgt.m, 8.7 lbf.ft)
/
E PLATE
74 N.m 17.5 kgl.m, 54 lbf.ftlTorque in a ctisscaoss oattern.
@
@
L
14-182
Trending: spare wheel, Emblem, brake pads, rear main seal, C432, trunk release, Gasket