lock HONDA CIVIC 2001 7.G Repair Manual

µ
Î ÎÌÌÌ
Î
ÌÎÌ
Maint enance
198 Service at the indicated distance or time whichever comes first. miles x
1,000
km x 1,000
months Replace every 5,000 miles (8,000 km) or 6 months
Service the following items at the recommended intervals
Every 36 months
At 120,000 miles (192,000 km) or 120 months,
then every 60,000 miles (96,000 km) or 60 months Every 110,000 miles (176,000 km) or 84 months
Inspect every 110,000 miles (176,000 km), otherwise adjust only if noisy Every 110,000 miles (176,000 km)
Every 15,000 miles (24,000 km) in dusty conditions,
otherwise use normal schedule
1016
2032304840645080609670
112 80
128 90
144 100160110176120192
See information on maintenance and emissions warranty, last column, page .
See Air Conditioning Filter on page for replacement information under special driving conditions.
See timing belt on page to determine need for replacement.
Replace engine oil and filter
Rotate tires (Check tire inflation and condition at least once per month)
Inspect front and rear brakes
Lubricate locks and hinges
Visually inspect the following items:
Tie rod ends, steering gear box and boots, Suspension components
Driveshaft boots
Check parking brake adjustment
Visually inspect the following items: Brake hoses and lines (including ABS)
All fluid levels and condition of fluids
Cooling system hoses and connectionsExhaust system, Fuel lines and connections
Lights and controls, Vehicle underbody
Inspect and adjust drive belts
Replace air conditioning filter
Replace transmission fluid
Replace air cleaner element
Replace spark plugs
Inspect valve clearance
Replace timing belt , and inspect water pump
Inspect idle speed
Replace engine coolant
Replace brake fluid 24 48 72
12 36 60
MT AT
1:2: : 231
233 195
1
2Maintenance Schedule for Severe Conditions

µµ
Ø Ø Ø ØØØ Ø ØØØØØ Ø ØØØØØØØ Ø
Ì Ì
Î
CONT INUED
Maint enance199
U.S. Owners
Canadian Owners
AB C D EF
Service at the indicated distance or time, whichever comes first.
Refer to page to determine which schedule to use.Use the Maintenance Schedule for Severe Conditions.
Do items in A.
Do items in A, B.
Do items in A, E.
DoitemsinA,B,C.
Do items in A.
DoitemsinA,B,D,E.
Do items in A.
DoitemsinA,B,C.
DoitemsinA,E,F.
Do items in A, B.
Do items in A.Replace transmission fluid (MT, AT).
DoitemsinA,B,C,D,E.
Do items in A.
Do items in A, B.
Do items in A, E.
DoitemsinA,B,C.
Do items in A. Replace transmission fluid (AT).
DoitemsinA,B,D,E. Replace engine oil and filter.
Inspect front and rear brakes.
Rotate tires (follow pattern on page 237 ).
Lubricate all hinges, locks, and latches with
multipurpose grease.
Inspect tie rod ends, steering gear box and boots.
Inspect suspension components.
Inspect driveshaft boots.
Check parking brake adjustment.
Inspect brake hoses and lines (including ABS).
Check all fluid levels, condition of fluids, and check
for leaks.
Inspect cooling system hoses and connections.
Inspect exhaust system.
Inspect fuel lines and connections.
Check all lights.
Inspect the underbody.
Inspect and adjust drive belts.
Replace air conditioning filter .
Replace air cleaner element every 15,000 mi/
24,000 km (independent of time).
Replace brake fluid every 3 years (independent ofmileage).
5,000 mil/8,000 km/6 mos
10,000 mil/16,000 km/1 yr
15,000 mil/24,000 km/1-½ yrs
20,000 mil/32,000 km/1 yr
25,000 mil/40,000 km/2 yrs
30,000 mil/48,000 km/2 yrs
35,000 mil/56,000 km/2-½ yrs
40,000 mil/64,000 km/2 yrs
45,000 mil/72,000 km/3 yrs
50,000 mil/80,000 km/3 yrs
55,000 mil/88,000 km/3-½ yrs
60,000 mil/96,000 km/3 yrs
65,000 mil/104,000 km/4 yrs
70,000 mil/112,000 km/4 yrs
75,000 mil/120,000 km/4-½ yrs
80,000 mil/128,000 km/4 yrs
85,000 mil/136,000 km/5 yrs
90,000 mil/144,000 km/5 yrs
194
1
Maintenance Schedule for Severe Conditions (listed by distance/time)

Remove the radiator cap by
pushing down and turning
counterclockwise.
Turn the radiator cap counter-
clockwise, without pressing down
on it, until it stops. This relieves
any pressure remaining in the
cooling system.
Pour coolant into the reserve tank.
Fill it to half way between the MAX
and MIN marks. Put the cap back
on the reserve tank.
Put the radiator cap back on.
Tighten it f ully.
The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low. Do not add any rust inhibitors or
other additives to your car’s cooling
system. They may not be compatible
with the coolant or engine compo-
nents.
2. 3. 4. 5. 6.
Cooling Syst em
Maint enance
210
RRAADDIIAATTOORRCCAAPPRREESSEERRVVEETTAANNKK

CONT INUED
Remove the radiator cap.
Turn the ignition ON (II). Turn
the temperature control dial to
maximum heat. Turn of f the
ignition. Open the hood. Make
sure the engine and radiator are
cool to the touch.
Loosen the drain plug on the
bottom of the radiator. The
coolant will drain through the
splash guard. Remove the drain
bolt and washer f rom the engine
block.
Draining the coolant requires access
to the underside of the car. Unless
you have the tools and knowledge,
you should have this maintenance
done by a skilled mechanic.
Thecoolingsystemshouldbe
completely drained and ref illed with
new coolant according to the time
and distance recommendations in
the maintenance schedule. Only use
Honda All Season Antif reeze/
Coolant Type 2.
1.3.
2.
Replacing Engine Coolant
Cooling Syst em
Maint enance
211

Tightening torque:
When the coolant stops draining,
tightenthedrainpluginthe
bottom of the radiator. Apply non-
hardening sealant to the drain bolt
threads, put a new washer on the
drain bolt, and reinstall the drain
bolt in the engine block. Tighten it
securely.
Pour Honda All Season
Antif reeze/Coolant Type 2 into
the radiator up to the base of the
f iller neck. This coolant is a
mixture of 50 percent antif reeze
and 50 percent water. Pre-mixing
is not required.The cooling system capacity is:
10.
11.
CONT INUED
With 5-speed manual transmission:With automatic transmission:
Cooling Syst em
Maint enance 213
FFIILLLLEERRNNEECCKK
FFiilllluuppttoohheerree
58 lbf·ft (78 N·m , 8.0 kgf·m) 1.06 US gal (4.0
, 0.88 Imp gal)
1.03 US gal (3.9
, 0.86 Imp gal)

A low power steering f luid level can
indicate a leak in the system. Check
the f luid level f requently and have
the system inspected as soon as
possible.
Always use Honda Power Steering
Fluid. If it is not available, you may
use another power steering f luid as
an emergency replacement.
However, continued use can cause
increased wear and poor steering in
cold weather. Have the power
steering system f lushed and ref illed
with Honda PSF as soon as possible.
You should check the f luid level in
the power steering reservoir at least
once a year. Check the level when
the engine is cold. Look at the side
of the reservoir. The f luid should be
between the UPPER LEVEL and
LOWER LEVEL. If it is below the
LOWER LEVEL, add power steering
f luid to the UPPER LEVEL.
Power Steering
Maint enance
220
UUPPPPEERRLLEEVVEELL
LLOOWWEERRLLEEVVEELL T urning the steering wheel to f ull lef t
or right lock and holding it there can
damage the power steering pump.

The spark plugs in your car should
be replaced according to the time
and distance recommendations in
the maintenance schedule.Disconnect the wire connector
f rom the ignition coil by pushing
on the lock tab and pulling on the
connector. Pull on the plastic
connector, not the wires.
Remove the cover by turning the
two clips one quarter turn
counterclockwise.
Clean up any dirt and oil that have
collected around the ignition coils.
1. 2.
3.
CONT INUED
Maint enance
Spark Plugs
Replacement
223
CCLLIIPPSS

´ µ
Spark Plug Gap:
Push the wire connector onto the
ignition coil. Make sure it locks in
place.
Repeat this procedure f or the
other three spark plugs.
Reinstall the cover.
Install the ignition coil. Reinstall
the nut.
NGK:
DENSO:
8.
11.
10. 9.
Maint enance
Spark Plugs
Specif ications:
225
PZFR6F-11
PKJ20CR-M11
0.04 in (1.1 mm) 0
0.1 mm
Tighten the spark plugs caref ully. A
spark plug that is too loose can
overheat and damage the engine.
Overtightening can cause damage to
the threads in the cylinder head.

Disconnect the blade assembly
fromthewiperarmbypushingin
the lock tab. Hold it in while you
push the blade assembly toward
thebaseof thearm.
Raise the wiper arm of f the
windshield.
To replace the blade:
Check the condition of the wiper
blades at least every six months.
Look f or signs of cracking in the
rubber, or areas that are getting
hard. Replace the blades if you f ind
these signs, or they leave streaks
and unwiped areas when used.
2.
1.
Wiper Blades
Maint enance
228
WWIIPPEERRAARRMMSS
LLOOCCKKTTAABB

Remove the blade f rom its holder
by grasping the tabbed end of the
blade. Pull f irmly until the tabs
come out of the holder.Examine the new wiper blades. If
they have no plastic or metal rein-
f orcement along the back edge,
remove the metal reinf orcement
strips f rom the old wiper blade and
install them in the slots along the
edge of the new blade.Slide the new wiper blade into the
holder until the tabs lock.
Slide the wiper blade assembly
onto the wiper arm. Make sure it
locks in place.
Lower the wiper arm down against
the windshield.
3. 4. 5. 6. 7.
Wiper Blades
Maint enance
229
BBLLAADDEE
BBLLAADDEE
RREEIINNFFOORRCCEEMMEENNTT