Door HONDA CIVIC 2003 7.G Owner's Manual
[x] Cancel search | Manufacturer: HONDA, Model Year: 2003, Model line: CIVIC, Model: HONDA CIVIC 2003 7.GPages: 1139, PDF Size: 28.19 MB
Page 667 of 1139
3. Check that the door and body edges are parallel. lf
necessary, adjust the door cushions (A) to make the
rear of the door flush with the bodv.
Apply body paint to the hinge mounting bolts and
around the hinges.
Check for water leaks (see step 7 on page 20-12).
Test-drive and check for wind noise.
5.
Door Striker Adjustment
Make sure the door latches securely without slamming
it. lf necessary, adjust the striker (A): The striker nuts
are fixed, but the striker can be adjusted slightly up or
down, and in or out.
1. Loosen the screws (B), rhen insert a shop towel (C)
between the body and striker.
Lightly tlghten the screws.
Wrap the striker with a shop towel, then adjust the
striker by tapping it with a plastic hammer (D). Do
not tap the striker too hard.
Loosen the screws, and remove the shop towel.
Lightly tighten the screws.
Hold the outer handle out, and push the door
against the body to be sure the striker allows a
flush fit, lf the door latches properly, tighten the
screws and recheck.
5.
6.
8 x 1.25 mm18 N.m 11.8 kgf m, 13 lbf.ft)
20-13
Page 669 of 1139
Power Mirror Replacement
1.
2.
5.
Lower the door glass fully.
Carefully pry out the mirror mount cover (A) by
hand in the sequence shown. Disconnect the
tweeter connector (B), and release the wire harness
(C) from the hook (D).
Fastener Location
) : Clip, 1
3. Remove the door panel (seepage20-4).
4. Disconnectthe connector (A), and detach the
harness clip (B). While holding the mirror {C),
remove the nuts, then remove the mirror. Take care
not to scratch the door.
Fastener Locrtions
O: Nut.3
lnstall the mirror in the reverse order of removal,
and note these items:
. Make sure the connector is plugged in properly.
. Attach the harness clip.
Mirror Holder Replacement
1. Carefully pulloutthe bottom edge ofthe mirror
holder (A) by hand. Take care not to scratch the
mrrror.
5.
Separate the mirror holder from the actuator (B) by
slowly pulling them apart while detaching the clips
(C). lf equipped, disconnect the mirror defogger
connectors{D) from the heater pad terminals.
lf equipped, reconnect the mirror defogger
connectors.
Reattach the clips of the mirror holder to the
actuator, then position the mirror holder on the
actuator. Carefully push on the clip portions of the
mirror holder untilthe mirror holder locks into
prace.
Check the operation of the actuator
20-15
Page 677 of 1139
19. With a sponge, apply a light coat of body primer to
the original adhesive remaining around the
windshield opening flange, Let the body primer dry
for at least 10 minutes:
. Do not apply glass primer to the body, and be
careful not to mix up glass and body primer
sponges.. Never touch the primed surfaces with your hands.. l\4ask off the dashboard before paintingthe
flange.
20 mm(0.79 in.l
Before filling a cartridge, cut a "V" in the end of the
nozzle (A) as shown.
20.
12 mm (0.47 in.)
7 mm {0.27 in.)
21. Pack adhesive into the cartridge without air pockets
to ensure continuous delivery. Put the cartridge in a
caulking gun, and run a bead of adhesive (A)
around the edge of the windshield (B) between the
dams (C) and molding (D) as shown. Apply the
adhesive within 30 minutes after applying the glass
primer. Make a slightly thicker bead at each corner.
l'1fifr.,1:?mm n10.28 in.l ,..-A.. )t
$?I.",x1"u.80.".,trl
.,r []\"Inside
-'
A
Use suction cups to hold the windshield over the
opening, align it with the alignment marks made in
step 16, and set it down on the adhesive. Lightly
push on the windshield until its edges are fully
seated on the adhesive allthe way around. Do not
open or close the doors until the adhesive is dry.
c.. N\F12mm I nl{0.08 in.} I 'Z l
./"
(cont'd)
20-23
Page 678 of 1139
Glass
23.
24.
Windshield Replacement (cont'd)
Scrape or wipe the excess adhesive off with a putty
knife or towel. To remove adhesive from a painted
surface or the windshield, wipe with a soft shop
towel dampensd with alcohol.
Let the adhesive dry for at least t hour, then spray
water over the windshield and check for leaks.
Mark Ieaking areas, and let the windshield dry, then
seal with sealant:
. Let the vehicle stand for at least 4 hours after
windshield installation. lf the vehicle has to be
used within the first 4 hours, it must be driven
slowly.. Keep the windshield dry for the first hour after
installation.
Reinstallthe cowl covers (see page 20-95).
NOTE:The cowl cover clips may not set properly if
the windshield adhesive is too wet.
Install the clips (A, B) on both side trim {C). lf the
clip (D) is damaged, replace the side trim and clips
as an assembly.
A: GreyB: Blue
20-24
27. On both sides ofthe windshield, install the side
trim (Alto the clip (B), then set the bottom edge of
the side trim over the cowl cover (C), and align the
clips (D)with the retainers (E), and push on the clipportions of the trim until the trim is fully seated on
the windshield.
Reinstall all remaining removed parts. Installthe
rearview mirror after the adhesive has dried
thoroughly.
NOTE: Advise the customer not to do the following
things for 2 to 3 days:
. Slam the doors with allthe windows rolled up.. Twist the body excessively (such as when going
in and out of driveways at an angle or driving
over rough, uneven roads).
28.
Page 683 of 1139
19. Use suction cups to hold the rear window over the
opening. align it with the alignment marks you
made in step '13, and set it down on the adhesive.
Lightly push on the rear window until its edges are
fully seated on the adhesive all the way around. Do
not open or close the doors until the adhesive is dry.
20. Scrape or wipe the excess adhesive off with a putty
knife or towel. To remove adhesive from a painted
surface or the rear window, use a soft shop towel
dampened with alcohol.
21. Let the adhesive dry for at least 'l hour,thenspray
water over the rear window and check for leaks.
Mark the leaking areas, let the rear window dry,
then seal with sealant. Let the vehicle stand for at
least 4 hours after rear window installation, lf the
vehicle has to be used within the first 4 hours, it
must be driven slowly.
22. Reinstallall remaining removed parts.
NOTE: Advise the customer not to do the following
things for 2 to 3 days:
. Slam the doors with all the windows rolled up.. Twist the body excessively (such as when going
in and out of driveways at an angle or driving
over rough, uneven roads).
Ouarter Glass Replacement
NOTE:. Put on gloves to protect your hands.. Wear eye protection while cufting the glass adhesive
with piano wire,. Use seat covers to avoid damaging any surfaces.
1. Remove the C-pillar trim (see page 20-51).
lf necessary, remove the rear side trim panel (see
page 20-51 ) and B-pillar upper trim (see page 20-
50).
2. Remove the front seal {A) from the front edge of the
glass (B). lf necessary, cut the seal with a utility
knife.
(cont'd)
20-29
Page 688 of 1139
Glass
Ouarter Glass Replacement (cont'd)
17. Use suction cups (A)to hold the quarter glass over
the opening. align it with the clips (B) and set it
down on the adhesive. Lightly push on the quarter
glass until its edges are fully seated on the
adhesive all the way around. Do not open or close
the doors untilthe adhesive is drv.
18. Scrape or wipe the excess adhesive off with a putty
knife or towel. To remove adhesive from a painted
surface or the quarter glass, use a soft shop towel
dampened with alcohol.
19. Let the adhesive dry for at least t hour,thenspray
water over the quarter glass and check for leaks,
Mark the leaking areas, let the quarter glass dry,
then seal with sealant. Let the vehicle stand for at
least 4 hours after quarter glass installation. lf the
vehicle has to be used within the first 4 hours. it
must be driven slowlv.
20. Reinstall all remaining removed parts.
NOTE: Advise the customer not to do the following
things for 2 to 3 days:
. Slam the doors with all the windows rolled up.. Twist the body excessively (such as when going
in and out of driveways at an angle or driving
over rough, uneven roads).
20-34
Page 696 of 1139
Moonroof
1.
Frame and Drain Tube Replacement
Remove these items:
. Headliner (see page 20-54). Moonroof glass (see page 20-37)
Put on gloves to protect you r hands. Disconnect the motor connector (A), open/close-tilt/close switch connector
{B), moonroof control unit connector {C), auto-stop switch connector (D), and the drain tubes (Ei, and remove the
moonroof relays (F).
Fastenor Locations
> : Bolt, 10
{um
/^
6x1.0mm9.8 N.m(1.0 kgf.m,7.2lbf ft)
4.
5.
2.
irl
@
Remove the interior harness (G) by detaching the harness clips (H).
With an assistant holding the frame (l). remove the bolts, starting at the rear, and release the rear hooks (J) by
moving the f rame forward, then remove the frame.
With the help of an assistant, carefully remove the frame through the passenger's door opening. Take care not to
scratch the interior trim and body, or tear the seat covers.
20-42
Page 703 of 1139
Interior Trim
Component Location Index
HATCH LOWER TRIM PANELoaoe 20-53
HATCH SIDE TRIMpage 20 53
C-PILLAR TRIMpage 20'51
REAR SIDE SHELFpage 20 5l
REAR SIDE TRIM PANELpage 20-51
B.PILLAR UPPEB TRIMpage 20-50
DOOR OPENING TRIMpage 20-50
A.PILLAR TRIMpage 20-50
Removal/lnstallation, page 20 54
KICK PANELpage 20 50
DOOR SILL TRIMpage 20-50
Replacement,page 20-55
CARGO AREA FLOORpage 20-52
REAR CENTER SHELFpage 20-51
CARGO FLOOR MATpage 20-52
REAR TRIM PANELpage 20-52
20-49
Page 704 of 1139
Interior Trim
Trim Removal/lnstallation - Door Area
NOTE:. Put on gloves to protect your hands.. When prying with a flat-tip screwdriver, wrap it with protective tape to prevent damage.. Take care not to bend or scratch the trim and panels.
1. Remove the trim as shown. To remove the door silltrim and B-pillar upper trim, remove the rear side trim panelas necessary (see page 20-51).
2. Installthe trim in the reverse order of removal, and note these items:
. Replace any damaged clips.. Apply liquid thread lock to the anchor bolts before reinstallatior,.. Before installing the anchor bolts, make sure there are no twists or kinks in the belts.
Fastener Locations
B>rClip,3 C>:Clip,?{White)
FRONT SEAT BELTUPPER ANCHOR BOLT7/16-20 UNF32 N m (3.3 kgf m,24 lbf.ft)
A-PILLAR TRIM
il-::7
/ ao----- LowER ANcHoR cAP
FRONT SEAT BELT LOWERANCHOR BOLT7/16-20 UNF32 N.m (3.3 kgt.m,24lbl.ftl
,"lF
{
A >: Clip,2(Black)
2ffi
Tl|t
\
KICK PANEL
REAR SIDE TRIM PANEL
20-50
Page 709 of 1139
4. Remove the headliner.
-1 Remove the socket plug (A).
-2 Remove the remaining door opening trim {B}
from each roof portion.
-3 Detach the clips (C), and release the fasteners
(D) by pulling the front portion ofthe headliner
(E) down.-4 With the help of an assislant, release the clips(F) of the headliner from the moonroof frame
(G), and release the headliner from the clips (H)
by sliding the headliner forward, and lowering
the headliner.-5 Remove the headliner through the passenger's
opening.
Fastener Locations
C>:Clip,3
ao
5.Install the headliner in the reverse order of removal,
and note these items:
. When reinstalling the headliner through the
passenger's door opening, be careful not to fold
or bend it, Also, be careful not to scratch the
DOOy.. Check that both sides of the headliner are
securely attached to the trim.. Replace any clips that remain in the roof during
removal. Reinstallthe clips back in the headliner
before installation.
F>:Clip,2 H>:Clip,2
Carpet Replacement
SRS components are located in this area. Reviewthe
SRS component locations (see page 23-13) and the
precautions and procedures (see page 23-14) in the SRS
section before performing repairs or service.
NOTE:. Put on gloves to protect your hands.. Take care not to damage, wrinkle. or twist the carpet.. Be careful not to damage the dashboard or other
interior trim pieces.
1. Remove these items:
. Front seats, both sides (see page 20-111. Driver's dashboard under cover (see page 20-60). Passenger's dashboard Iower cover (see page
20-631. Rear seat cushion (see page 20-80). Kick panels, both sides (see page 20-50). Door silltrim, both sides (see page 20-50). Consoles, front and rear (see page 20-57)
2. Remove the nut (A), and using a hex wrench,
release the clip (B), then remove the footrest (C).
Fastener Locations
Aa:Nut,1 B):Clip,'l
--'1 I
-- -JrL
tj I ;tt4f=\-/ l[il
A6x1.0mm9.8Nm11.0 kgf m,7.2 lbf.ft)
-o
(cont'd)
20-55