ECO mode HONDA CIVIC COUPE 2007 8.G User Guide

Release the switch and, within 5
seconds, turn the ignition switch
to the ACCESSORY (I) position.
On A/T vehicles, move the shift
lever to the P position.
Turn the ignition switch to the
LOCK (0) position.
5.
6.
Door L ocks
82
master door lock switch on the
driver’s door. You will hear a click. Keep holding the switch until you
hear another click (after about 5 seconds). Push and hold the front of the
4.Locks all doors when the vehi cl e's speed
reaches about 9 mph (15 km/h).
Apply the parking brake.
On A/T vehicles, push and hold
the brake pedal, and move the
shift lever out of P.
1.
3.
To program the Drive Lock mode:
A/T models
Turn the ignition switch to the ON
(II) position, and close the driver’s
door.
2.
Pushandholdthe
front of the
master door lock switch on the
driver' s door. You will hear a
click. Keep holding the switch
until you hear another click (after
about 5 seconds).
Release the switch and, within 5
seconds, turn the ignition switch
to the LOCK (0) position.
4.
5.

The driver’s door or all doors can be
set to unlock automatically in two
CONT INUED
Door L ocks
A uto Door Unlock Modes
Inst rument s and Cont rols
83
modes for automatic transmissionvehicles (Park Unlock mode or
Ignition Switch Unlock mode) and
one mode for manual transmission
vehicles (Ignition Switch Unlock
mode). The default setting from the
factory is the driver’s door unlocks in
Park Unlock mode (A/T) or IgnitionSwitch Unlock mode (M/T). To
program modes, refer to the following
instructions.
Apply the parking brake.
Turn the ignition switch to the ON
(II) position, and open the driver’s
door.
On A/T vehicles, move the shift
lever to P.
1.
2.
3.
To turn off the Auto Door Lock
modes:Push and hold the front of the
master door lock switch on the
driver' s door until you hear a
click (af ter about 5 seconds).
Release the switch and, within
5 seconds, turn the ignition
switch to the LOCK (0) position.
4.
5.

Apply the parking brake.
Turn the ignition switch to the ON
(II) position, and close the driver’s
door.
1.
2.
Unlocks the driver’s door or all doors
when the i gnition switch is moved out of the ON (II) position.
Door L ocks
To program the Ignition SwitchUnlock mode:
84
A/T models
Move the shift lever to P, and close
the driver’s door.
Turn the ignition switch to the ON
(II) position. Apply the parking brake.
1.
2.
3.
To program the Park Unlock mode:
Unlocks the driver’s door or all doorsWhen the shift lever is moved into thePark (P) position (automatic
transmission vehicles only).
• U ntil you hear another click (after about 5 seconds) to activate
driver's door unlock, or
• U ntil you hear two more clicks
(af ter about 10 seconds) to
activate all doors unlock .
Release the switch and, within 5
seconds, turn the ignition switch
to the LOCK (0) position. Pushandholdtherearof the
master door lock switch on the
driver' s door. You will hear a
click. Continue to hold the switch:
4.
5.

CONT INUED
Door L ocks
Inst rument s and Cont rols
85
On A/T vehicles, push and hold
the brake pedal, then move the
shift lever out of P.
Pushandholdtherearof the
master door lock switch on the
driver’ s door. You will hear a
click. Continue to hold the switch:
• Until you hear another click
(after about 5 seconds) to
activate driver's door unlock, or
• U ntil you hear two more clicks
(af ter about 10 seconds) to
activate all doors unlock .
Release the switch and, within 5
seconds, turn the ignition switch
to the ACCESSORY (I) position.
On A/T vehicles, move the shift
lever to P.
3.
4.
5.
Turn the ignition switch to the
LOCK (0) position.
6.
Turn the ignition switch to the ON
(II) position, and open the driver’s
door.
On A/T vehicles, move the shift
lever to P. Apply the parking brake.
1.
2.
3.
To turn off the Auto Door Unlock
modes:
Release the switch and, within 5
seconds, turn the ignition switch to
the LOCK (0) position. P ush
a
ndholdtherearof the
master door lock switch on the
driver’ s door. You will hear a click
and, af ter about 5 seconds, you
will hear another click.
4.
5.

µµ
µ
µ
Press this button once to
lock all doors. Some exterior lights
will f lash once. When you push
LOCK twice within 5 seconds, you
will hear a horn to verif y that the
doors are locked. You cannot lock
the doors if any door is not f ully
closed or the key is in the ignition
switch. If you unlock the doors with the
remote transmitter, but do not open
any of the doors within 30 seconds,
the doors automatically relock. On
U.S. LX, EX and Si models, the
security system will also set.
Pressthisbuttonfor
about 1 second to attract attention;
the horn will sound, and the exterior
lights will f lash f or about 30 seconds.
To cancel panic mode, press any
other button on the remote
transmitter, or insert the key.
Press this
button f or about 1 second to open
the trunk. You cannot open the trunk
if the key is in the ignition switch.
The ceiling light (if the ceiling light
switch is in the door activated
position) will come on when you
press the UNLOCK button. If you do
not open any door, the light stays on
f or about 30 seconds, then f ades out.
If you relock the doors with the
remote transmitter before 30
seconds have elapsed, the light goes
of f immediately. Press this button once
to unlock the driver’s door. Push it
twice to unlock the other doors.
Some exterior lights will f lash twice
each time you press the button. This
button does not work when the key
is in the ignition switch. If you push the LOCK button twice
within 5 seconds, you will hear a
horn to verify that the security
system has set.
On U.S. LX, EX and Si models
OnU.S.EXandSimodels
LOCK PA NIC
T RUNK REL EA SE
UNL OCK
Remote Transmitter
88
LOCK
BUTTON
TRUNK
RELEASE
BUTTON
PANIC BUTTON
UNLOCK BUTTON
PANIC BUTTON UNLOCK
BUTTON
LOCK
BUTTON
U.S. EX and Si models
U.S.: LX model
Canadian: LX, DX-G and EX models

The ceiling light has a three-position
switch;ON(right),DoorActivated,
andOFF(left).IntheDoor
Activated (center) position, the light
comesonwhenyou:Open any door.
Remove the key from the ignition.
Unlock the doors with the key or
the remote transmitter. The f ront ceiling light has a two-
position switch; Door Activated and
OFF.
The f ront ceiling light has two
spotlights. Push the spotlight lenses
to turn them on and off.
After all doors are closed tightly, the
light(s) dims slightly, then f ades out
in about 30 seconds.
If you do not open any door af ter you
unlock the driver’s door or remove
the key from the ignition switch, the
light(s) f ades out in about 30
seconds.
If you leave any door open without
the key in the ignition switch, the
ceiling light(s) will go of f af ter 3
minutes.On models with moonroof
On models with moonroof
CONT INUED
Ceiling L ight
Spotlights
Interior Lights
Inst rument s and Cont rols
101
DOOR ACTIVATED OFF
OFF ON
SWITCHES
DOOR
ACTIVATED

To change the letter, select the
previous segment by pushing the
bottom of the SEEK button.
Turn the TUNE knob to change a
letter.
Push the top of the SEEK button
to select the next segment, then
turn the TUNE knob to select a
letter. Repeat this procedure to set
your message. The system will return to the audio
display about 5 seconds af ter you
stop selecting a letter.
Your audio system shows a welcome
message on the display when you
turn the ignition switch to the
ACCESSORY (I) or the ON (II)
position. You can see a message
‘‘WELCOME’’ on the display when
your vehicle was new.
You can also customize this welcome
message to your liking with the
audio controls.
Youcansetuptoabout16
characters on the display.
To select a character:
Make sure the audio system is of f .
PushandholdtheTUNEknob,
then push the power/volume knob
on the audio control panel. You
will see the f irst letter blinking.
2. 3.
4.
1.
Audio System (4-door Si only) (Models without navigation system)
To Customize a Message
112
TUNE KNOB
POWER/VOLUME
KNOB
SEEK BUTTON

µ
µ
µµ
µ
If you do nothing, the system will
then scan f or the next strong station
and play it f or 10 seconds. When it
plays a station you want to listen to,
press the SCAN button again.
Use the TUNE knob to
tune the radio to a desired f requency.
Turn the knob right to tune to a
higher f requency, or lef t to tune to a
lower f requency.
The scan f unction samples
all stations with strong signals on the
selected band. To activate it, press
the SCAN button, then release it.
You will see SCAN in the display.
The system will scan f or a station
with a strong signal. When it f inds
one, it will stop and play that station
f or about 10 seconds. The SEEK f unction
searches up and down from the
current f requency to f ind a station
with a strong signal. To activate it,
press the or side of the
SEEK button, then release it. Each side of the buttons
(1 through 6) can store one
f requency on AM, and two
f requencies on FM.
Repeat steps 1 through 3 to store a
total of six stations on AM and
twelve stations on FM. Pick a preset number (1 6), and
hold it until you hear a beep. Usethetune,seek,orscan
function to tune the radio to a
desired station. Select the desired band, AM or
FM. FM1 and FM2 let you store
twelve stations.
The ignition switch must be in the
ACCESSORY (I) or ON (II) position.
Turn the system on by pushing the
power/volume knob or the AM or
FM button (the AM/FM button on
models with XM radio available).
Adjust the volume by turning the
power/volume knob.
The band and f requency that the
radio was last tuned to is displayed.
To change bands, press the AM/FM
button (AM or FM button). On the
FM band, ST will be displayed if the
stationisbroadcastinginstereo.
Stereo reproduction in AM is not
available.
You can use any of f ive methods to
f ind radio stations on the selected
band: tune, seek, scan, the preset
buttons, and auto select.
1.
2.
3.
4.
TUNE
SCAN SEEK
Preset
To Select a Station
Audio System (Models without navigation system)
114

µ
To turn of f auto select,pressthe
A. SEL (auto select) button. This
restores the presets you originally
set. Press the SOUND (TUNE) knob
repeatedly to display the bass (BAS),
treble (TRE), fader (FAD), balance
(BAL), and speed-sensitive volume
compensation (SVC) settings.
Eachmodeisshowninthedisplayas
it changes. Turn the SOUND
(TUNE) knob to adjust the setting to
your liking. When the level reaches
the center, you will see ‘‘ ’’ in
the display. The system will
automatically return the display to
the selected audio mode about 5
seconds af ter you stop adjusting a
mode.
If you are
traveling far from home and can no
longer receive your preset stations,
you can use the auto select feature to
find stations in the local area.
Press the A. SEL button. ‘‘A.SEL’’
f lashes in the display, and the system
goes into scan mode f or several
seconds. It stores the f requencies of
six AM, and twelve FM stations in
the preset buttons. You will see a ‘‘0’’ displayed af ter
pressing a preset button if auto
select cannot f ind a strong station f or
every preset button.
If you do not like the stations auto
select has stored, you can store
other f requencies on the preset
buttons as previously described.
CONT INUED
Adjusting the Sound
AUTO SELECT
Audio System (Models without navigation system)
Features
115

µµ
µ
These two
modes adjust the strength of the
sound coming from each speaker.
BALANCE adjusts the side-to-side
strength, while FADER adjusts the
front-to-back strength. You
can use the instrument panel
brightness control buttons to adjust
the illumination of the audio system
(see page ). The audio system
illuminates when the parking lights
are on, even if the radio is of f .
The SVC
mode controls the volume based on
vehicle speed. The f aster you go, the
louder the audio volume becomes.
As you slow down, the audio volume
decreases.
The SVC has f our modes; SVC OFF,
SVC LOW, SVC MID, and SVC
HIGH. The def ault setting is MID.
Turn the SOUND (TUNE) knob to
adjust the setting to your liking.
If you f eel the sound is too loud,
choose low. If you f eel the sound is
too quiet, choose high.
Use the TREBLE/
BASS modes to adjust the tone to
your liking.
73
Balance/Fader A udio System L ighting
Speed-sensitive volume
compensation (SVC)
Treble/Bass
Audio System (Models without navigation system)
116