HONDA CIVIC HATCHBACK 2002 7.G Owners Manual

Ø Ø Ø Ø ØØØ Ø ØØ Ø
ÎÎÎ
ÎÎ Î
Ì Î ÎÎ
Maint enance244
See information on maintenance and emissions warranty, last
column, page .
See timing belt on page to determine need for replacement.
Balancer belt applies to 4-cylinder models only.
Check engine oil and coolant at each fuel stop.
Check and adjust valve clearance, cold engine, only if noisy. See Dust and Pollen Filter on page for replacement
information under special driving conditions.
:
1:2:3: 239
283
NOTE: 28267,500 mi/108,000 km
71,250 mi/114,000 km
75,000 mi/120,000 km/5 yrs
78,750 mi/126,000 km
82,500 mi/132,000 km
86,250 mi/138,000 km
90,000 mi/144,000 km/5 yrs
6 yrs (independent ofmileage)
90,000 mi/144,000 km/6 yrs
93,750 mi/150,000 km
97,500 mi/156,000 km
101,250 mi/162,000 km
105,000 mi/168,000 km/7 yrs
108,750 mi/174,000 km
112,500 mi/180,000 km
116,250 mi/186,000 km
120,000 mi/192,000 km/8 yrs
120,000 mi/192,000 km/10 yrs,
then replace every 60,000 mi/
96,000 km/5 yrs
120,000 mi/192,000 km/6 yrs
120,000 mi/192,000 km/7 yrsDo items in A,B.
Do items in A.
Clean air cleaner element.
DoitemsinA,B,C.
Do items in A.
Do items in A, B.
Do items in A. Replace AT fluid.
Do item in E.
DoitemsinA,B,C,D.
Do items in A.
Do items in A, B.
Do items in A. Replace timing belt , balancer belt , and
inspect water pump. Inspect valve clearance.
Check idle speed.
Clean air cleaner element.
Replace spark plugs.
DoitemsinA,B,C.
Do items in A.
Do items in A, B.
Do items in A.
Replace timing belt , balancer belt , and
inspect water pump.
DoitemsinA,B,C,D. Replace engine coolant
Replace MT fluid
Replace AT fluid
11 ,2
11 ,2
Maintenance Schedule for Severe Conditions (listed by distance/time)

Maint enance
Required Maintenance Record (f or Normal and Severe Schedules)
246
63,750 mi
67,500 mi
71,250 mi
75,000 mi
78,750 mi
82,500 mi
86,250 mi
90,000 mi93,750 mi
97,500 mi
101,250 mi
105,000 mi
108,750 mi
112,500 mi
116,250 mi
120,000 mi
Signature or dealer stamp mi/km
Date
mi/kmDate
mi/kmDate
mi/kmDate
mi/kmDate
mi/kmDate
mi/kmDate
mi/kmDate Signature or dealer stamp mi/km
Date
mi/kmDate
mi/kmDate
mi/kmDate
mi/kmDate
mi/kmDate
mi/kmDate
mi/kmDate
102,000 km
108,000 km
114,000 km
120,000 km
(or 5 years)
126,000 km
132,000 km
138,000 km
144,000 km
(or 6 years) 150,000 km
156,000 km
162,000 km
168,000 km
(or 7 years)
174,000 km
180,000 km
186,000 km
192,000 km
(or 8 years)

Fluid Locations
Maint enance
6-cylinder Models
249
EENNGGIINNEEOOIILLFFIILLLLCCAAPP
PPOOWWEERRSSTTEEEERRIINNGGFFLLUUIIDD((RReeddccaapp))
BBRRAAKKEEFFLLUUIIDD((GGrraayyccaapp))
WWAASSHHEERRFFLLUUIIDD((BBlluueeccaapp))
CCOOOOLLAANNTTRREESSEERRVVOOIIRR
AAUUTTOOMMAATTIICCTTRRAANNSSMMIISSSSIIOONNFFLLUUIIDDDDIIPPSSTTIICCKK((YYeelllloowwlloooopp))
EENNGGIINNEEOOIILLDDIIPPSSTTIICCKK((OOrraannggeelloooopp))
RRAADDIIAATTOORRCCAAPP

Open the hood and remove the
engine oil f ill cap. Remove the oil
drain bolt and washer f rom the
bottom of the engine. Drain the oil
into an appropriate container.Remove the oil f ilter and let the
remaining oil drain. A special
wrench (available from your
Honda dealer) is required to
remove the f ilter.
Install a new oil f ilter according to
instructions that come with it.
Put a new washer on the drain bolt,
then reinstall the drain bolt.
Tighten it to:
4. 5.
3.
2.
CONT INUED
Engine Oil
Maint enance253
44--ccyylliinnddeerrmmooddeellss
DDRRAAIINNBBOOLLTT
66--ccyylliinnddeerrmmooddeellss44--ccyylliinnddeerrmmooddeellss
DDRRAAIINNBBOOLLTTWWAASSHHEERROOIILLFFIILLTTEERRWWAASSHHEERR
33 lbf·ft (44 N·m , 4.5 kgf·m)

Refill the engine with the recom-
mended oil.
Engine oil change capacity
(including f ilter):Let the engine run f or several
minutes and check the drain bolt
and oil f ilter f or leaks.
Turn of f the engine, let it sit f or
several minutes, then check the oil
level. If necessary, add oil to bring
the level to the upper mark on the
dipstick.
Replace the engine oil f ill cap.
Start the engine. The oil pressure
indicator light should go out within
f ive seconds. If it does not, turn of f
the engine and reinspect your
work.
9.
8.
7.
6. (4-cylinder models)
(6-cylinder models)
Engine Oil
Maint enance254
OOIILLFFIILLTTEERR
66--ccyylliinnddeerrmmooddeellss
4.6 US qt (4.4, 3.9 Imp qt)
4.5 US qt (4.3
, 3.8 Imp qt) Improper disposal of engine oil can be
harmf ul to the environment. If you
change your own oil, please dispose of
the used oil properly. Put it in a sealed
container and take it to a recycling
center. Do not discard it in a trash bin
or dump it on the ground.

Remove the radiator cap by
pushing down and turning
counterclockwise.
The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.
Put the radiator cap back on.
Tighten it f ully.
Make sure the engine and radiator
are cool.
Turn the radiator cap counter-
clockwise, without pressing down
on it, until it stops. This relieves
any pressure remaining in the
cooling system.3.
1.
2.4. 5.
Cooling Syst em
Maint enance256
44--ccyylliinnddeerrmmooddeellss66--ccyylliinnddeerrmmooddeellssRRAADDIIAATTOORRCCAAPP
RRAADDIIAATTOORRCCAAPP

Loosen the drain plug on the
bottom of the radiator. The
coolant will drain through the
splash guard. Remove the drain
bolt and washer f rom the engine
block.
Openthehood.Makesurethe
engine and radiator are cool to the
touch.
Turn the ignition ON (II). Turn
the temperature control dial to
90°F (32°C). Turn of f the ignition
and remove the key.
Remove the radiator cap.
Turn the ignition ON (II). Turn
the temperature control Dial all
the way clockwise. Turn of f the
ignition and remove the key.
1.
3.
2.
4-cylinder models
EX V-6 model
Except EX V-6 model
Maint enance
Cooling Syst em
258
44--ccyylliinnddeerrmmooddeellss66--ccyylliinnddeerrmmooddeellss44--ccyylliinnddeerrmmooddeellss
DDRRAAIINNBBOOLLTT
DDRRAAIINNPPLLUUGG

Remove the reserve tank f rom its
holder by pulling it straight up.
Drain the coolant, then put the
tank back in its holder.
Loosen the drain plug on the
bottom of the radiator. The
coolant will drain through the
splash guard. Loosen the drain
bolt. When removing the reserve tank,
f irst remove the cruise control cable
and the ground cable f rom their clips.
Af ter installing the tank back in
place, put the cables back in their
clips.
4.
3.6-cylinder models 6-cylinder models
CONT INUED
Cooling Syst em
Maint enance259
66--ccyylliinnddeerrmmooddeellss
RREESSEERRVVEETTAANNKKRREESSEERRVVEETTAANNKKCCAAPP
44--ccyylliinnddeerrmmooddeellssHHOOLLDDEERR
DDRRAAIINNPPLLUUGG
DDRRAAIINNBBOOLLTT66--ccyylliinnddeerrmmooddeellss

When the coolant stops draining,
tightenthedrainplugatthe
bottom of the radiator.
Put a new washer on the drain bolt,
then reinstall the drain bolt in the
engine block. Tighten it securely.
Tightening torque:Tighten the drain bolt at the rear
of the engine cylinder block
securely.
Tightening torque:
Loosen the bleeder bolt on top of
the engine.
Pour Honda All Season
Antif reeze/Coolant Type 2 into
the radiator. This coolant is a
mixture of 50 percent anti-f reeze
and 50 percent water. Pre-mixing
is not required.
Tighten the bleeder bolt when
coolant comes out in a steady
stream with no bubbles.
7.
6.
5.
4-cylinder models 6-cylinder models 4-cylinder models
Cooling Syst em
Maint enance260
FFIILLLLEERRNNEECCKK
44--ccyylliinnddeerrmmooddeellssFFiilllluuppttoohheerree
FFIILLLLEERRNNEECCKK
66--ccyylliinnddeerrmmooddeellssFFiilllluuppttoohheerree
RREESSEERRVVEETTAANNKKCCAAPPRREESSEERRVVEETTAANNKK
66--ccyylliinnddeerrmmooddeellssHHOOLLDDEERR
61 lbf·ft (83 N·m , 8.5 kgf·m)
7 lbf·ft (10 N·m , 1.0 kgf·m)

Start the engine and hold it at
1,500 rpm until the cooling f an
comes on. Turn of f the engine.
Check the coolant level in the
radiator and add coolant if needed.
Start the engine and let it run f or
about 30 seconds. Then turn of f
the engine.
Fill the radiator with coolant up to
the base of the f iller neck.
Fill the reserve tank to the MAX
mark. Install the reserve tank cap.
Install the radiator cap, and
tighten it to the first stop.
Start the engine and let it run until
the radiator cooling f an comes on
at least twice. Then stop the
engine.
Remove the radiator cap. Pour
coolant into the radiator up to the
base of the f iller neck and into the
reserve tank up to the MAX mark. If necessary, f ill the reserve tank
to the MAX mark. Install the
reserve tank cap.
Install the radiator cap, and
tighten it fully.
Pour coolant into the radiator up
to the base of the f iller neck.
The cooling system capacity is: 8. 9.
10. 11.12. 13. 14. 15. 16.
With automatic transmission:
6-cylinder models
With 5-speed manual transmission:
6-cylinder models
Cooling Syst em
Maint enance261
44--ccyylliinnddeerrmmooddeellssBBLLEEEEDDEERRBBOOLLTT
1.45 US gal (5.5, 1.21 Imp gal)
1.43 US gal (5.4
, 1.19 Imp gal)
1.48 US gal (5.6
, 1.23 Imp gal)