Oil pump HONDA CR-V 2000 RD1-RD3 / 1.G User Guide

HONDA CR-V 2000 RD1-RD3 / 1.G User Guide CR-V 2000 RD1-RD3 / 1.G HONDA HONDA https://www.carmanualsonline.info/img/13/5778/w960_5778-0.png HONDA CR-V 2000 RD1-RD3 / 1.G User Guide

Page 168 of 1395

HONDA CR-V 2000 RD1-RD3 / 1.G User Guide 
Crankshaft
12.
Installation (contd)
14.
13.
Apply liquid gasket to the oil pump mating surfaceof the block.
Apply a light coat of oil to the crankshaft, the lip ofthe seal, and the O-rings.
Apply gr

Page 169 of 1395

HONDA CR-V 2000 RD1-RD3 / 1.G User Guide 
Oil Seals
18. Tighten the bolts and nuts finger tight at six points.
Tighten all bolts and nuts, starting from nut O. clock-
wise in three steps. Excessive tightening can cause
distortion ot the oil

Page 171 of 1395

HONDA CR-V 2000 RD1-RD3 / 1.G User Guide 
Engine Lubrication
Speciaf Tools .......... ...".""8-2
lllustrated Index ........... ....8-3
Engine Oil
Inspection ................... 8-4
Replacement ....................................... 8

Page 173 of 1395

HONDA CR-V 2000 RD1-RD3 / 1.G User Guide 
lllustrated Index
OIL CONTROLORIFICE
OIL PUMPOverhaul, page 8-8Removal/lnspection, page 8 IApply liquid gasket tomating surface of engine block.
99 - 00 models:KNOCK SENSOR31 N.m {3.2 kgf.m.23 lbl.f

Page 177 of 1395

HONDA CR-V 2000 RD1-RD3 / 1.G User Guide 
Oil Pressure SwitchOil Pressure
Testing
Remove the YEL/RED wire from the engine oil pres-
sure swrtcn.
Check for continuity between the positive terminal
and the engine {ground). There should be cont

Page 178 of 1395

HONDA CR-V 2000 RD1-RD3 / 1.G User Guide 
Oil Pump
Overhaul
6xl.0mm9.8 N m (1.0 kg,t m, 7.2 lbf ftl
6x1.0mm5 N.m {0.5 kgt m. 4lbtft}OUTER ROTORInspection, pages 8-9, 1O
PUMP COVER
lnspection, pages 8-9, 10Apply liquid gasketto the mating sur

Page 179 of 1395

HONDA CR-V 2000 RD1-RD3 / 1.G User Guide 
1.
2.
3.
RemovaUlnspection/lnstallation
Drain the engine oil.
Turn the crankshaft, and align the white groove on
the crankshaft pulley with the pointer on the lower
cover.
Remove the cylinder head co

Page 180 of 1395

HONDA CR-V 2000 RD1-RD3 / 1.G User Guide 
Oil Pump
13.
Removal/lnspection/lnstallation (contd)
Check the housing-to-outer rotor radial clearance. lf
the housing-to-outer rotor radial clearance exceeds
the service limit, reDlace the set of i

Page 181 of 1395

HONDA CR-V 2000 RD1-RD3 / 1.G User Guide 
24.Apply grease to the lip of the oil pump seal.
Install the oil pump onto the crankshaft. When the
pump is in place, clean any excess grease off the
crankshaft and check that the oil seal lip is not

Page 288 of 1395

HONDA CR-V 2000 RD1-RD3 / 1.G User Guide 
PGM-FI System
Tho Maltunction Indicator Lamo(MlL) n6Yor como3 on leven lortwo laconds) rft6r tho ignhion isturnod ON {lll.
Turn th6 ignition switch ON (ll).
- Repair lhort or opcn in thowire between
Page:   < prev 1-10 11-20 21-30 31-40 41-50 50 next >