reset HONDA CR-V 2003 RD4-RD7 / 2.G Owners Manual
[x] Cancel search | Manufacturer: HONDA, Model Year: 2003, Model line: CR-V, Model: HONDA CR-V 2003 RD4-RD7 / 2.GPages: 374, PDF Size: 4.46 MB
Page 74 of 374
µBetween 8,000 miles (12,800 km)
and 10,000 miles (16,000 km) this
indicator will light f or two seconds
when you f irst turn the ignition
switch to ON (II), and then flash for
ten seconds.
If you exceed 10,000 miles (16,000
km) without having the scheduled
maintenance perf ormed, this
indicator will remain on as a constant
reminder.
This light comes on if the tailgate or
the hatch glass is not closed tightly.
This light comes on if any door is not
closed tightly.
For the f irst 8,000 miles (12,800 km)
af ter the Maintenance Required
Indicator is reset, it will come on f or
two seconds when you turn the
ignition switch to ON (II). Ref er to the Maintenance Schedules
f or Normal and Severe Driving
Conditions on pages.
This indicator reminds you that it is
time to take your vehicle in for
scheduled maintenance.
238 242
Indicator L ights
Maintenance Required
Indicator
Tailgate and Hatch Glass
Open Indicator
Door-open Indicator
Inst rument s and Cont rols70
Page 75 of 374
Your dealer will reset this indicator
af ter completing the scheduled
maintenance. If this maintenance is
done by someone other than your
Honda dealer, reset the indicator as
f ollows.Turn of f the engine.
Hold the button until the indicator
resets (approximately ten
seconds). Press and hold the Select/Reset
button on the instrument panel,
then turn the ignition switch ON
(II).
1.
2.
3.
Indicator L ights
Inst rument s and Cont rols71
Page 76 of 374
This shows your speed in miles per
hour (mph). The smaller inner
numbers are the speed in kilometers
per hour (km/h).
This shows your speed in kilometers
per hour (km/h). The smaller inner
numbers are the speed in miles per
hour (mph).
The tachometer shows the engine
speed in revolutions per minute
(rpm). To protect the engine f rom
damage, never drive with the
tachometer needle in the red zone.
U.S. modelsCanadian models
Gauges
Inst rument s and Cont rols
Speedometer
T achometer
72
ODOMETER/TRIP METER SELECT/RESET BUTTON
TACHOMETER SPEEDOMETER FUEL GAUGE
TEMPERATURE GAUGE
Page 77 of 374
CONT INUED
The odometer shows the total dis-
tance your vehicle has been driven.
It measures miles in U.S. models and
kilometers in Canadian models.
It is illegal under U.S. f ederal law and
Canadian provincial regulations to
disconnect, reset, or alter the
odometer with the intent to change
the number of miles or kilometers
indicated.
The trip meter shows the number of
miles (U.S.) or kilometers (Canada)
driven since you last reset it. There
are two trip meters: Trip A and Trip
B. Switch between these displays
and the odometer by pressing the
Select/Reset button repeatedly.
Each trip meter works independently,
so you can keep track of two
dif f erent distances.To reset a trip meter, display it, and
then press and hold the Select/Reset
button until the number resets to
‘‘0.0’’.
This indicator displays the outside
temperature in Centigrade.
Canadian models only
Inst rument s and Cont rols
Gauges
Odometer/T rip MeterOut side T emperat ure Indicat or
73
OUTSIDE TEMPERATURE INDICATOR
Page 116 of 374
If your vehicle’s battery is
disconnected or goes dead, or the
driver’s window f use is removed, the
AUTO f unction will be disabled. The
power window system needs to be
reset af ter reconnecting the battery
or installing the f use. You should do
the f ollowing.Start the engine. Push down on
the driver’s window switch until
the window is f ully open.
Pull back on the driver’s window
switch to close the window
completely, then hold the switch
f or a second or two more.
If the power windows do not operate
properly af ter resetting, have your
vehicle checked by a Honda dealer.
Auto reverse stops sensing when the
window is almost closed. You should
always check that all passengers and
objects are away from the window
bef ore closing it. If the driver’s window runs into any
obstacle while it is closing
automatically, it will reverse
direction, and then stop. To close the
window, remove the obstacle, then
use the window switch again.
Any impact due to road conditions
may cause the auto reverse f unction
work unexpectedly on the closing
window. If it happens f requently,
there is a problem with your power
window system. You should have
your vehicle inspected by your
dealer. You can still close the
window by pulling back on the
window switch lightly and hold it. 1.
2.
Power Windows
Inst rument s and Cont rols
Auto Reverse
112
Page 142 of 374
Your Honda’s audio system provides
clear reception on both AM and FM
bands, while the preset buttons allow
you to easily select your f avorite
stations.
The anti-thef t f eature will disable the
system if it is disconnected f rom the
vehicle’s battery. To get the system
working again, you must enter a
code number (see page ).178
On LX model in the U.S. and Canada
Audio System
Comf ort and Convenience Feat ures
A M/FM/Cassette/CD A udio
System
138
Page 143 of 374
CONT INUED
The ignition switch must be in
ACCESSORY (I) or ON (II) to
operate the audio system. Turn the
system on by pressing the PWR/
VOL knob, or the AM or FM button.
Adjust the volume by turning the
knob.
The band and f requency that the
radio was last tuned to is displayed.
To change bands, press the AM or
FM button. On the FM band, ST will
be displayed if the station is broad-
castinginstereo.Stereo
reproduction on AM is not available. Operating the Radio
Audio System
Comf ort and Convenience Feat ures139
PWR/VOL KNOBPRESET BUTTONS
AM BUTTON SEEK BUTTONSTUNE KNOB
SCAN BUTTON FM BUTTON
Page 144 of 374
µ
µ ÓÓ µ
µ
µ´
To store a f requency: Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each preset
button.
Pick the Preset button you want
for that station. Press the button
and hold it until you hear a beep.
Repeat steps 1 to 3 to store a total
of six stations on AM and twelve
on FM.
Once a station’s frequency is stored,
simply press and release the proper
preset button to tune to it.
You can use any of f ive methods to
f ind radio stations on the selected
band: TUNE, SEEK, SCAN, AUTO
SELECT, and the preset buttons.
Use the TUNE knob to
tune the radio to a desired f requency.
Turn the TUNE knob to the right to
tune to a higher f requency, or to the
lef t to tune to a lower f requency.
Turn the knob right or lef t until the
display reaches the desired
f requency.
The SEEK f unction
searches the band for a station with
a strong signal. To activate it, press
either SEEK button ( or ), then
release it. Depending on which
SEEK button you press, the system
scans upward or downward f rom the
current f requency. It stops when it
finds a station with a strong signal. The SCAN f unction
samples all the stations with strong
signals on the selected band. To
activate it, press the SCAN button,
then release it. You will see SCAN in
the display. The system will scan up
the band for a station with a strong
signal. When it f inds one, it will stop
and play that station for
approximately f ive seconds. If you do
nothing, the system will then scan
f or the next strong station and play
that f or f ive seconds. When it plays a
station that you want to continue
listening to, press the SCAN button
again.
You can store the
f requencies of your f avorite radio
stations in the six preset buttons.
Each button will store one f requency
on the AM band, and two
f requencies on the FM band. UsetheTUNE,SEEK,orSCAN
function to tune the radio to a
desired station.
The preset f requencies will be lost if
your vehicle’s battery goes dead, is
disconnected, or the radio f use is
removed. 1.
2.
3.
4.
Audio System
Comf ort and Convenience Feat ures
TUNE
SEEK SCAN
Preset
140
Page 145 of 374
µIf you are
traveling far from home and can no
longer receive the stations you
preset, you can use the Auto Select
feature to find stations in the local
area.
If you are in a remote area, Auto
Select may not f ind six strong AM
stations or twelve strong FM stations.
If this happens, you will see a ‘‘0’’
displayed when you press any preset
button that does not have a station
stored. To activate Auto Select, press the
A. SEL button. A. SEL will f lash in
the display, and the system will go
into scan mode f or several seconds.
It automatically scans both bands,
looking f or stations with strong
signals. It stores the f requencies of
six AM stations and twelve FM
stations in the preset buttons. You
can then use the preset buttons to
select those stations.
CONT INUED
AUTO SELECT
Audio System
Comf ort and Convenience Feat ures141
A. SEL BUTTON
A. SEL INDICATOR
Page 146 of 374
If you do not like the stations Auto
Select has stored, you can store
other f requencies in the preset
buttons. Use the TUNE, SEEK, or
SCAN f unction to f ind the desired
f requencies, then store them in the
selected preset buttons as described
previously.
Auto Select does not erase the
f requencies that you preset pre-
viously. When you return home, turn
of f Auto Select by pressing the
A. SEL button. The preset buttons
will then select the f requencies you
originally set.
Audio System
Comf ort and Convenience Feat ures142
SCAN INDICATORTUNE KNOB
SCAN BUTTON PRESET BUTTONS
SEEK BUTTONS