bulb HONDA ELEMENT 2008 1.G Owners Manual

If this indicator comes on when the
ignition switch is turned to the ON
(II) position and the parking brake is
released, it means there is a problem
in the circuit. Have your vehicle
checked by your dealer.
This indicator comes on when you
set the cruise control. See pagef or inf ormation on operating the
cruise control.
This indicator comes on f or a f ew
seconds when you turn the ignition
switch to the ON (II) position. It will
then go of f if you have inserted a
properly-coded ignition key. If it is
not a properly-coded key, the
indicator will blink, and the engine
will not start (see page ).
This indicator also blinks several
times when you turn the ignition
switch f rom the ON (II) position to
the ACCESSORY (I) or LOCK (0)
position.
The lef t or right turn signal indicator
blinks when you signal a lane change
or turn. If the indicators do not blink
or they blink rapidly, it usually
means one of the turn signal bulbs is
burned out (see page ). Replace
the bulb as soon as possible, since
other drivers cannot see that you are
signaling.
When you press the hazard warning
button, both turn signal indicators
and all turn signals on the outside of
the vehicle f lash.
76
204
135
Canadian models only
Instrument Panel Indicators
Cruise Control Indicator
‘‘Daytime Running
Lights’’ Indicator
Immobilizer System
Indicator Turn Signal and
Hazard Warning
Indicators
62
\f—\f—y
y
(+\fy\f\fy
2008 Element

Theheadlightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
cargo area or pull a trailer,
readjustment may be required.
Adjustmentsshouldbedonebyyour
dealer or other qualif ied technician.Your vehicle has halogen headlight
bulbs. Handle it by its steel base and
protect the glass f rom contact with
your skin or hard objects. If you
touch the glass, clean it with
denaturedalcoholandacleancloth.
Your vehicle has halogen headlight
bulbs, two on each side. When
replacing a bulb, handle it by its base
and protect the glass from contact
with your skin or hard objects. If you
touch the glass, clean it with
denaturedalcoholandacleancloth.
Open the hood.
If you need to change the
headlight bulb on the driver’s side,
remove the f ront end of the air
intake duct by pulling it out.
1.
On SC model
On all models except SC
On all models except SC
Headlight A iming Replacing a Headlight Bulb
Lights
202
AIR INTAKE DUCT
Halogen headlight bulbs get very hot
when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.
\f—\f—y
\fy
(+\fy\f\fy
2008 Element

Reinstall the rubber weather seal.
Make sure it is right side up; it is
marked ‘‘TOP.’’
Install the new bulb into the hole,
making sure the tabs are in their
slots. Pivot the hold-down wire
back in place, and clip the end into
the slot.
Push the electrical connector onto
the new bulb. Make sure it is
connected securely. Turn on the
headlights to test the new bulb.
(Driver’s side)
Install the f ront end of the air
intake duct.
Remove the rubber weather seal
by pulling on the tab.
Remove the electrical connector
f rom the bulb by pulling the
connector straight back.
Unclip the end of the hold-down
wire f rom its slot. Pivot the wire
out of the way, then remove the
bulb. The high beam headlight bulb and
the low beam headlight bulb are
replaced the same way.
Open the hood.
If you need to change the
headlight bulb on the driver’s side,
remove the f ront end of the air
intake duct by pulling it out.
1.
2.
3.
4. 5.
6.
7.
8.
CONT INUED
On SC model
Lights
Maint enance
203
AIR INTAKE DUCT
\f—\f—y
\f
\fy
(+\fy\f\fy
2008 Element

Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the headlights to test the
new bulb.
(Driver’s side)
Install the f ront end of the air
intake duct.
Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Remove the bulb by turning it one-
quarter turn counterclockwise.
Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
3.
4. 5.
6.
7.
2.
Lights
Replacing a Front Parking/Turn
Signal Light Bulb
204
TAB
On all models except SC
On SC model
\f—\f—y
\f
y
(+\fy\f\fy
2008 Element

Remove the socket f rom the light
assembly by turning it one-quarter
turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Place a cloth between the trim of
the lens and the body, at the top of
the lens. Remove the front side
marker light assembly by caref ully
prying on the trim of the lens with
a small f lat-tip screwdriver.
The f ront parking/turn signal light
is next to the headlight bulb. On
the driver’s side, remove the f ront
end of the air intake duct by
pulling it out (see page ).
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Testthelightstomakesurethe
new bulb is working.
Install the f ront end of the air
intake duct.
1. 2.
3.
1.
2.
3.
4.
5.
6. (Driver’s side)
202
CONT INUED
On all models except SC
Lights
Replacing a Front Side Marker
Light Bulb
Maint enance
205
SCREWDRIVER
CLOTH LIGHT
ASSEMBLY LIGHT ASSEMBLY
SOCKET
\f—\f—y
\f\fy
(+\fy\f
\fy
2008 Element

Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
The f ront side marker light is next
to the headlight bulb. On the
driver’s side, remove the f ront end
of the air intake duct by pulling it
out (see page ).
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Turn on the lights to make sure
the new bulb is working.
Put the light assembly back into
the body, bottom first. Push on the
top edge until it snaps into place.
Remove the socket f rom the light
assembly by turning it one-quarter
turn counterclockwise.Testthelightstomakesurethe
new bulb is working.
Install the f ront end of the air
intake duct.
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
1. 3.
2. 4.
5.
6.
4.
5.
6.
203On SC model
Lights
206
\f—\f—y
\fy
(+\fy\f

y
2008 Element

Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Testthelightstomakesurethe
new bulb is working.
When reinstalling the taillight
assembly, f irst place the two pins
in the holes in place. Tighten the
two mounting bolts.
Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Open the hatch and the tailgate.
Remove the two mounting screws
with a Phillips-head screwdriver,
and remove the taillight assembly
f rom the body by pulling it back.
Determine which of the three
bulbs is burned out: brake/
taillight, turn signal light or back-
up light. 6.
7.
5.
3.
4.
1.
2.
Lights
Replacing Rear Bulbs
Maint enance
207
SOCKET
SOCKET SOCKET
SCREW
SCREW
TAILLIGHT ASSEMBLY
\f—\f—y
\fy
(+\fy\f
y
2008 Element

Open the hatch. Remove the light
assembly cover by pushing in on
the tabs on both sides and pulling
the cover down.
Remove the socket f rom the light
assembly by turning it one-quarter
turn counterclockwise.
Turn on the parking lights and
check that the new bulb is
working.
Put the lens back into the light
assembly, right side f irst. Push on
the lef t edge until it snaps into
place.
Using a cloth to prevent scratches,
insert a small f lat-tip screwdriver
between the lef t edge of the lens
and the housing. The lens will
come down.
Pull the bulb straight out of its
socket. Push the new bulb in until
it bottoms in the socket. 1.
2.
3.
4.
1.
2.
Lights
Replacing a High-mount Brake
Light Bulb
Replacing a Rear License Plate
Bulb
208
COVER
TAB TAB
BULB
LENS
SCREWDRIVER
HOUSING
LENS
CLOTH
\f—\f—y
\fy
(+\fy\f
y
2008 Element

If your seat belts get dirty, use a sof t
brush with a mixture of mild soap
and warm water to clean them. Do
not use bleach, dye, or cleaning
solvents. Let the belts air-dry bef ore
you use the vehicle.
Dirt build-up in the loops of the seat
belt anchors can cause the belts to
retract slowly. Wipe the insides of
the loops with a clean cloth
dampened in mild soap and warm
water or isopropyl alcohol.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Press the brake pedal to make
sure the new bulb is working.
Put the socket back into the light
assembly, and turn it clockwise to
lock it in place.
Put the cover back onto the light
assembly. Push it on until it locks
in place. The floor mats that came with your
vehicle hook over the f loor mat
anchors. This keeps the f loor mats
f rom sliding f orward, possibly
interf ering with the pedals, or
backwards, making the f ront
passenger’s weight sensors
inef f ective.
3.
4.
5.
6.
CONT INUED
If equipped
Cleaning the Seat Belts Floor Mats
Lights, Cleaning the Seat Belts, Floor Mats
Maint enance
209
LOOP
BULB
SOCKET
\f—\f—y
\f\fy
(+\fy\f
y
2008 Element

CONT INUED
....................................
Accessories .147
ACCESSORY (Ignition Key
.......................................
Position) .79
..............
Accessory Power Sockets .98
....................
Additives, Engine Oil .194
.........
Advice f or Pregnant Women .18
.............................
Airbag (SRS) .11,24
...
Airbags, Additional Information .24
...
Additional Safety Precautions .36
.............................
Airbag Service .35
How the Passenger Airbag Of f
......................
Indicator Works .34
How the Side Airbag Of f ......................
Indicator Works .34
..
How the SRS Indicator Works .33
How Your Front Airbags
.........................................
Work .27
...
How Your Side Airbags Work .30
How Your Side Curtain Airbags
.........................................
Work .32
........................
SRS Components .24
..............
Air Conditioning System .102
.........................................
Usage .103
.......................
Air Pressure, Tires .213 ......................................
Alignment .250
......................................
Antif reeze .196
Anti-lock Brakes (ABS)
...............................
Indicator .61,168
...................................
Operation .167
..............
Anti-thef t, Audio System .131
.
Anti-thef t Steering Column Lock .79
......................
Armrests, Front Seat .84
................................
Audio System .107
...
Automatic Seat Belt Tensioners .22
.............
Automatic Speed Control .135
..............
Automatic Transmission .161
..........................
Capacity, Fluid .249
...............
Checking Fluid Level .198
.......................................
Shif ting .161
.
Shif t Lever Position Indicator .161
................
Shif t Lever Positions .161
....................
Shif t Lock Release .163
......................
Auxiliary Input Jack .125
Battery
Charging System ...........................
Indicator .60,235
............................
Jump Starting .231 ..............................
Maintenance .218
............................
Specif ications .250
..............................
Bef ore Driving .139
..................................
Belts, Seat .10,20
...........................
Beverage Holders .98
...................................
Body Panels .201
..................................
Booster Seats .52
Brakes
...........
Anti-lock System (ABS) .167
.............
Break-in, New Linings .140
....................
Bulb Replacement .207
...........................................
Fluid .200
.........................................
Parking .93
.................
System Indicator .60,237
........................
Wear Indicators .167
.............................
Braking System .166
.................
Break-in, New Vehicle .140
..
Brightness Control, Instruments .72
........................
Brights, Headlights .71
Index
A
B
INDEX
I
\f—\f—y


y
(+\fy\fy
2008 Element