change time HONDA INSIGHT 2010 2.G Owners Manual

This indicator comes on when you
turn on the cruise control system by
pressing the CRUISE button on the
steering wheel (see page ).
This indicator comes on when you
set the cruise control. See pagef or inf ormation on operating the
cruise control.
This indicator reminds you that the
exterior lights are on. It comes on
when the light switch is in either the
or position. If you turn the
ignition switch to the ACCESSORY
(I) or the LOCK (0) position without
turning of f the light switch, this
indicator will remain on. A reminder
chime will also sound when you open
the driver’s door.
This indicator comes on with the
high beam headlights. For more
inf ormation, see page .
This indicator also comes on with
reduced brightness when the
daytime running lights (DRL) are on
(see page ).
The lef t or right turn signal indicator
blinks when you signal a lane change
or turn. If an indicator does not blink
or blinks rapidly, it usually means
one of the turn signal bulbs is
burned out (see pages and ).
Replace the bulb as soon as possible,
since other drivers cannot see that
you are signaling.
When you press the hazard warning
button, both turn signal indicators
and all turn signals on the outside of
the vehicle f lash.
363 365
256
256
119
120 Cruise Main Indicator
Cruise Control Indicator
Lights On Indicator
High Beam Indicator
Turn Signal and
Hazard Warning
Indicators
Instrument Panel Indicators
Inst rument s and Cont rols
69
 —
—y

y
)"  y  y
2010 Insight

This shows how much f uel you have.
It may show slightly more or less
than the actual amount. The needle
returns to the bottom after you turn
of f the ignition.
To switch the lower segment of the
multi-inf ormation display between
the odometer with the outside
temperature and trip meter with the
outside temperature, press the sel/
reset knob repeatedly. For more
inf ormation, see page . Eachtimeyoupressandholdthe
km/mile change knob, the
speedometer reading switches
between miles per hour (mph) and
kilometers per hour (km/h).
78 Fuel Gauge
Sel/Reset K nob K m/Mile Change K nob
Gauges
Inst rument s and Cont rols
73
SEL/RESET KNOB KM/MILE CHANGE KNOB
Avoid driving with an extremely low
f uel level. Running out of f uel could
cause the engine to misf ire, damaging
the catalytic converter.
 —
—y


y
)"  y  y
2010 Insight

ÛÝ
ÛÝ
ÛÝ
The multi-inf ormation display
changes to the blank display shown
above several seconds after you turn
the ignition switch to the ON (II)
position.
With the ignition switch in the ON
(II) position, the multi-inf ormation
display changes as shown on the
next page each time you press the
INFO ( / ) button or the SEL/
RESET button.
Multi-Inf ormation Display
76
U.S. model is shown. SEL/RESET BUTTON
INFO ( / ) BUTTON
Models with cruise control SEL/RESET BUTTON
Models without cruise control
INFO BUTTONS ( / )
 —
—y

y
)"  y  
y
2010 Insight

The odometer shows the total
distance your vehicle has been
driven. It measures miles in U.S.
models and kilometers in Canadian
models. It is illegal under U.S.
federal law and Canadian provincial
regulations to disconnect, reset, or
alter the odometer with the intent to
change the number of miles or
kilometers indicated.This meter shows the number of
miles (U.S.) or kilometers (Canada)
driven since you last reset it. There
are two trip meters: Trip A and Trip
B. Each trip meter works
independently, so you can keep track
of two dif f erent distances.When you reset Trip A, average f uel
economy A is reset at the same time.
When you reset Trip B, average f uel
economy B is reset.
In the customizing mode, you can set
Trip A and average f uel economy A
to reset at the same time when you
ref uel your vehicle (see page ).
To reset a trip meter, display it, then
press and hold the SEL/RESET
button until the number resets to
‘‘0.0’’. 99
Odometer
T rip Meter
Multi-Inf ormation Display
Inst rument s and Cont rols
79
TRIP METER A
TRIP METER B
ODOMETER U.S. model is shown.
U.S.
CANADA
 —
—y

y
)"  y  y
2010 Insight

This shows the average speed you
are traveling in miles per hour (mph)
f or U.S. models or kilometers per
hour (km/h) f or Canadian models.
This shows the accumulated
traveling time since you last reset it.
When you turn the ignition switch to
the ON (II) position, ELAPSED
TIME is reset.
This shows the estimated distance
you can travel on the fuel remaining
in the f uel tank. This distance is
estimated f rom the f uel economy
you received over the last several
miles(U.S.) or kilometers (Canada),
so it will vary with changes in speed,
traf f ic, etc.
If you want to reset the ELAPSED
TIME manually, go to the trip
computer’s ELAPSED TIME display,
andpressandholdtheSEL/RESET
button until the number resets.
You can customize the ELAPSED
TIME reset conditions on the multi-
inf ormation display (see page ).To reset the AVG. SPEED reading,
press and hold the SEL/RESET
button until the number resets.
100
EL A PSED T IME
RANGE A VG. SPEED
Multi-Inf ormation Display
Inst rument s and Cont rols
83
 —
—y

y
)"  y  y
2010 Insight

ÎÎÎ
Î Î
Î
Î Î
µ™¶ ™
µ™¶ ™
Î TRIP B
15 sec
Changes the language used in the display.
Changes the outside temperature reading above or
below its current reading.
Causes trip meter A and the average fuel economy
to reset when you refuel.
Resets the elapsed time of your current trip.
Changes the displayed measurement on the multi-
information display.
Turn the ambient meter feature on or off.
Changes how long (in seconds) the interior lights
stay on after you close the doors. ENGLISH
FRENCH
SPANISH
5°F 0°F 5°F
(U.S.) 3°C 0°C 3°C
(Canada)
ON
OFF
IGN OFF
TRIP A
AUTO
KM
MILES
ON
OFF
60 sec
30 sec
MET ER SET UP
(P.96)
LIGHTING SETUP
(P.104)
97
98
99
100
101
103
105
LANGUAGE SELECT ION
ADJUST OUTSIDE
TEMP. DISPLAY
TRIP A RESET with REFUEL
ELAPSED TIME RESET
DISPLAY KM/MILES
METER COLOR CHANGE
INTERIOR LIGHT
DIMMING T IME
Default setting
:
Description Setting Option
Group Setup Page
Menu Item
Multi-Inf ormation Display
92
 —
—y

y
)"  y  y
2010 Insight

Î
Î
Î
Î
Î
Î
Î
Menu Item Description Setting Option
Group Setup Page
AUTO DOOR LOCK
AUTO DOOR UNLOCK
DOOR LOCK MODE
KEYLESS LOCK
ACKNOWLEDGMENT
SECURITY RELOCK
TIMERChanges when the doors automatically lock.
Changes when the doors automatically unlock.
Changes which doors unlock with the remote
transmitter in a first push.
The exterior lights flash each time you press the
LOCK or UNLOCK button. A beeper will also
sound when you press the LOCK button twice.
Changes how long it takes (in seconds) for the
doors to relock and the security system to set after
you unlock but do not open the door.
Set/Cancel all the customized settings as default. SHIFT FROM P
WITH VEH SPD
OFF
IGN OFF
OFF
DRIVER DOOR
ALL DOORS
ON
OFF
90 sec
60 sec
30 sec
SET
CANCEL
DOOR SETUP
(P.106)
DEFAULT ALL
(P.115)
107
108
110
112
113
115
Default setting
:
SHIFT TO P DRIVER DOOR /
AL L DOORS
Multi-Inf ormation Display
Inst rument s and Cont rols
93
 —
—y

y
)"  y  y
2010 Insight

ÛÝÛ
Ý
ÛÝ
You can customize some of the
vehicle control settings to your
pref erence. Here are the settings
you can customize:
METER SETUP
When you want to change the
vehicle control settings, press the
INFO ( / ) button to select CHG
SETTING, then press the SEL/
RESET button. Each time you press the INFO ( /
) button, the screen changes as
shownonthenextpage.Pressthe
INFO ( / ) button until you see
the setup you want to customize,
then press the SEL/RESET button
to enter your selection.
If you do not make any changes,
select ‘‘EXIT.’’ The display returns to
the normal display.
You can also use the select/reset
knob in the instrument panel. Turn
the knob to select a setting and press
it to enter your selection.
If you want the settings as they were
when the vehicle lef t the f actory,
select DEFAULT ALL, as described
on page .
LIGHTING SETUP
DOOR SETUP
115
Customize Settings
Multi-Inf ormation Display
94
 —
—y

 y
)"  y  y
2010 Insight

Û
Ý
ÛÝ
ÝÛ
LANGUAGE SELECTION
ADJUST OUTSIDE TEMP.
DISPLAY
Here are the f our custom settings
forthemetersetup:
TRIP A RESET with REFUEL
Each time you press the INFO ( / ) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection. While ‘‘METER SETUP’’ is shown,
press the SEL/RESET button to
enter the customize mode. METER COLOR CHANGE DISPLAY KM/MILES
ELAPSED TIME RESET
Meter Setup
Multi-Inf ormation Display
96
: Press the SEL/RESET button.
: Press the INFO button .
: Press the INFO button . See page
103
Seepage101
See page
97See page 98Seepage99 See page
100
 —
—y

y
)"  y 
 
y
2010 Insight

ÛÝ
ÛÝ
Adjust Outside Temp. Display
If you sometimes f ind that the
temperature reading is a f ew
degrees above or below the actual
temperature, you can adjust it by
f ollowing these instructions: Adjust the outside temperature value
by pressing the INFO ( / ) button
repeatedly. Press the SEL/RESET
button to set the desired value.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘ADJUST OUTSIDE TEMP.
DISPLAY’’ and repeat the procedure
again.
You can choose this item to
customize f rom ‘‘METER SETUP’’
by pressing the INFO ( / ) button
repeatedly.
Press the SEL/RESET button to
enter the setting.
Multi-Inf ormation Display
98
Canadian models
Canadian models
U.S. models
U.S. models
 —
—y


y
)"  y 
 y
2010 Insight