transmission HONDA INTEGRA 1994 4.G Manual PDF

Pressure Testing
a While testing, be caretul of the rotating flont wheels.a Make aura litts, jacks, and sat€ty stands alo placedplop6rly {see section 1}.
CAUTION: Betore t€sting, be sure the transmission fluidis tilled to rh6 ploper l€vet.
1. Raise the car (see section i),
2. Warm up the engine {the cooling fan comes onl, thenstop the engine and connect a tachometer.
3. Connect the oil pressure gauge to each inspectionholels).
TOROUE: 18 N.m (1.8 kgf.m, 13 tbf.fr)
CAUTION: Connect ths oil prsssure gauge s€cur€_ly; be sule not to allow dust and other foleign pani_cl6s to 6nt€1 th€ inspection holo.
A/T OIL PRESSURE GAUGESET WPANEL07406-002oi+oo
A/T LOW PRESSUREGAUGE W/PANEL07/rO6-0O70300
A/T OIL PRESSURE HOSE,22'10 mmOTMAJ_PY4OI TA{4 Roquirod)
A/T OIL PRESSUBE HOSEADAPTEROTMAJ - PY/+O12014 Roqui.odl
NOTE: Use the A/T Oil Pressure Gauge Set (07406_O02OOO3) or A/T Low Pressure Gauge (07406-OOTO0OO). and the oil pressure gauge hoses and adap_ters shown above.
14-94
4. Start the engine, and measure the respective pres-
sure as follows.
a Line Pressure
a Clutch Pfessure
a Clutch Low/High Pressure
a Throttle B Pressure
5. Install a new washer and the sealing bolt in the in-spection hole and tighten to the specified torque.
TOROUE: 18 N'm {1.8 kgf.m, 13 tbf.ft)
NOTE: Do not reuse old aluminum washers.
a Line Pressure M€asurement
- 1 . Set the parking brake and block both rear wheelssecurely.
-2. Run the engine at 2,OOO rpm
-3. Shift the selecr lever to S or @ position.
-4. Measure line pressure.
LINE PRESSUREINSPECTION HOLE
NoTE: Higher pressures may be indicated it measurements are made in selector positions other than @ or @ position.
PRESSURESELECTOR
POStTTONSYMPTOMPROBABLE CAUSEFLUID PRESSURE
StandardService Limit
LineNo'ENo (or low)
lrne pressureTorque converter,
orl pump, pressure
regulator, to.que
convener check
valve
83O-88O kPa(8.5-9.O kgf/cm,,
120- I 30 psi)
78O kPa
{8.0 kgl/cm,, 1lO psi}

Transmission
Removal
4.Bemove the t.ansmission ground cable from the
transmission hanger.
Disconnect the lock-uD control solenoid valve con-
nector and the shitt control solenoid valve connec-
tor, then remove the harness clamp on the lock-up
control solenoid harness from the harness stav.
a Make sur€ lifts. iacks and safety stands are placad
properly, and hoist brackots are attachod to tho cor-
rect position on ths sngine {seo sectionl }.o Apply parking brake and block rear wheels, so car will
not roll off stands and fall on you whil6 working un-
del it
CAUTION: Use tender covers to avoid damsging paint-
ed surlaces,
1 . Disconnect the battery negative { - } and positive ( + )
cables from the battery.
2. Remove the intake air duct and air cleaner housino
assembly.
HARNESS CLAMP
LOCK-UP CONTROLSOLENOID VALVECONNECTOR
AIR CLEAI{ERHOUSING ASSEMBLY
SHIFT CONTROLSOLENOID VALVECONNECTORTRANSMISSIONGROUND CABI-E
Disconnect the vehicle speed sensor (VSS), main-
shaft sDeed sensor and countershaft speed sensor
connectors.
3.Remove the starter motor cables and cable holder
from the starter motor.VEHICLE SPEEDSENSOR CONNECTOR
STARTER MOTOR CABLECABLE HOLDER
VEHICLE SPEEDSENSOR
COUNTERSHAFTSPEED SENSORCONNECTOR
MAINSHAFT SPEEDSENSORCONNECTOR (cont,d)
STARTER MOTOR?/\
STARTER MOTOR CABLE
4-99

Transmission
Removal {cont'd)
7. Remove the transmission housing mounting bolts.
Remove the drain plug and drain the automatic trans-
mission tluid (ATF). Reinstall the drain plug with anew sealing washer lsee page 14-93).
DRAIN PLUG18 x 1.5 mm49 N'm 15.0 kgt-m,36 tbt-fr)
9. Remove the splash shield.
6 x 10
CLIPS pcs.
10. Remove the cotter pins and castle nuts, then
separate the balljoints from the lower arm {see sec-
tion 18).
11. Remove the right dampe. fork bolt. then separate
right damper fork and damper.
PINCI{ BOLT
SELF.LOCKINGNUTReplace.COTTER PINReplace.
/\
14-100
DAMPER FORK
CASTLE NUT

Transmission
Removal (cont'dl
'1 9.Remove the right tront mount/bracket, then remove
the end ol the throttle cont.ol cable trom the throt-
tle control lever.
Remove the ATF cooler hoses at the joint pipes. Turn
the ends of the cooler hoses up to prevent ATF from
flowing out, then plug the joint pipes.
NOTE: Check tor any sign ot leakage at the hosejoints.
THROTTLE CONTROL
23. Place a jack under the transmission, raise the lrans-
mission just enough to take weight off ol the
mounts. then remove the transmission mount.
20.
RrcHT FRoNT iiouNT/BRAcKET BoLTsATF COOLERHOSESReplace.24. Remove the t.ansmission housing mounting bolts
and rear engine mounting bolts.
25. Pull the transmission away from the engine until it
clears the 14 mm dowel Dins, then lower it on the
transmission iack.
21. Remove the engine stiftener and totque converter
cover.
22. Remove the eight drive plate bolts one at at time
while rotating the crankshaft pulley.
WASHERSReplace.
'i z/'l e
" (-J t'
14-102

lllustrated lndex
Transmission Housing
@
TT I]
I ',
a''-.2
14-106

O) COUNTERSHAFT REVERSE GEAR COLLAR
@ NEEDLE BEARING
G) COUNTERSHAFT REVERSE GEAR
@ LOcK WASHER Reptace.
@ REVERSE sHIFT FoRK
@ BEVERSE SELECToR
O REVERSE SELECToR HUB
@ couNTERSHAFT 4TH GEAR
@ NEEDLE BEARING
@ DTSTANCE COLLAR, 29 mm Setecrive part.
@ coUNTERSHAFT 2ND GEAR
@ THRUST NEEDLE BEARING
@ GoUNTERSHAFT 3RD GEAR
@ NEEDLE BEARING
@ THRUST NEEDLE EEARING
G) COUNTERSHAFT 3RD GEAR COLI-AR
O 3RD cLuTcH ASSEMBLY
(!) O-RINGS Replace.
@ coUNTERSHAFT
@ REVERSE IDLER GEAR
@ SNAP RING
@ THRUST WASHER
@ THRUST NEEDLE BEARING
@ MAINSHAFT 4TH GEAR
@) NEEDLE BEARINGS
@ THRUST NEEDLE BEARING
@ MAINSHAFT 4TH GEAR coLLAR
@ 2ND/4TH cLUTcH ASSEMBLY
et O-RINGS Replace.
@ THRUST waSHER, 36.5 x 55 mm Setective pan.
@ THRUST NEEDLE EEARING
@ MA|NSHAFT 2ND GEAR
€, NEEDI.E BEARING
@ THRUST NEEDLE EEARING
.O MAINSHAFT
@ SEAL|NG RtNGs, 3s mm
@ SEAL|NG R|NG, 29 mm
@ NEEDLE BEARING
@ sET RING
@ 1ST-HOLD CLUTCH
@ O-RING Replace.
@ THRUST WASHER
@ THRUST NEEDLE BEARING
@ NEEDLE BEARING
@ SUB.SHAFT 4TH GEAR
@ THRUST NEEDLE BEARING
@ SUB.SHAFT 4TH GEAR COLLAR
@ SUB-SHAFT
@ SUB.SHAFT NEEDLE BEARING
@ NEEDLE BEARING SToPPER
@ otL GUTDE cAP Reptace.
@ REVERSE IDLER G€AR SIIAFT/HOLDER
@ NEEDLE BEARII{G
@ sHIFT GONTROL SOLENOID vAI.vE ASSEMBLY
PROTECTOR
@ sHrFT CONTROL SOLENOTD VALVE A/B
@ SHIFT CONTROL SOLENOID VALVE A/B FILTER/GASKET
Replace.
@ TRANSMISSION HANG€R
@ TRANSMtsstoN MouI{T BRAGKET
@ oll SEAL Replace.
@ sET RING Replace.
@ TRANSMISSION HOUSING GASKET Replace.
@ DOWEL PrN
@ SNAP RI G
@ SUB-SHAFT IRANSMtSStON HOUSNG AEARTNG
@ MAINSHAFT TRANSMISSION HOUSING BEARING
@ coUNTERSHAFT TRANSMISSION HOUSING BEARING
@ DIFFERENTIAL ASSEMELY
@ OtL SEAL Replace.
@ CoNNECTOR STAY
TOROUE SPECIFICATIONS
Rel No.Torque ValueBolt SizeRemarks
B
E
H
12 N.m (1.2 kgf.m,8.7 lbt.tt)
14 N.m (1 .4 kgf .m. 10 lbf .ft)
44 N.m (4.5 kgt.m, 33 lbf .ft)
64 N.m (6.5 kgf .m, 47 lbf .ft)
6 x 1.O mm
6 x 1.O mm'lO x 1.25 mm
12 x 1.25 mm
Special bolt
14-107

Right Side Cover
Removal
NOTE:
a Clean all pans thoroughly in solvent or carburetor cleaner, and dry with compressed air,
a Blow out all passages.
a When removing the transmission right side cover, replace the following:. Right side cover gasket. Lock washers. O-rings. Each shaft locknut. Conical spring washers. Sealing washers
RIGHT SIDE COVER
SIDE COVER PROTECTOR
1.O mm BOLTS
SUB.SHAFTReplace.
THROTTLE CONTBOLLEVER
MAINSHAFT1ST GEAR
CONICALSPRINGWASHERReplace.WASHERReplace.
PARKING GEAR
ONE.WAY CLUTCHSUB.SHAFT 1ST GEAN
JOINT AOLT
THRUST WASHER,I ST GEAB COLLAR
1ST GEAR
NEEDLE BEABING
lST GEAR COLLAR
ATF LEVEL GAUGE
SEALING WASHERSReplace.
14-110
ATF COOLER PIPES

Remove the 13 bolts securing the right side cover
and right side cover protector, then remove them.
Slip the special tool onto the mainshaft as shown.
MAINSHAFT HOLOER07GAB-PF50101
3. Engage the parking brake pawl with the parking gear.
4. Align the hole ot the sub-shaft l st gear with the hole
of the the transmission housing, then insert a pin to
lock the sub-shaft while removing the sub-shaft
locknut.
'1.
COUNTERSHAFTLOCKNUTReplace.
MAINSHAFTLOCKNUTReplace.
8 mm pin.
comm€rciallyavailable
SU8-SHAFTLOCKNUTReplace.
Align the holes.
CONICAL SPNINGWASHERSReplace.
5. Pry the lock tab of the mainshaft locknut.
6. Cut the lock tabs of the countershaft and sub-shaft
locknuts using a chisel as shown. Then remove the
locknut from each shatt.
NOTE;
a Mainshaft and countershaft locknuts have lett-
hand threads.
a Clean the old countershaft locknut, it is used to
install the parking gear on the countershaft.a Always wear safety glasses.
CAUTION:
Keop all of th€ chis€led panicles out of the
tlanamigsion.
llrF-"""*
,fl(,-..- LocKNUr
@-.**'o'
7.
8.
q
10.
11.
12.
13.
14.
15.
to.
Remove the lock pin that was installed to hold the
sub-shaft.
Remove the special tool from the mainshaft after
removing the locknut.
Remove the 1st clutch and mainshaft 1st gear as-
sembly from the mainshaft.
Remove the sub-shaft 1st gear,
Remove the parking brake pawl.
Using a universal two jaw puller. remove the park-
ing gea.. one-way clutch and counlershatt 1st gear
assembly.
PARKING GEAR
Remove the parking brake lever from the control
shaft.
Remove the throttle control lever from the throttle
control shaft.
Remove the ATF cooler pipes.
Remove the ATF level gauge.
14-111

Transmission Housing
Removal
TRANSMTSSTOIr HOUSIIGMOUNTING BOLTS
TSAt{SMtSStOt{HANGER
fl
TRANSMISSIO HOUSII{G
TRA[{SMrSSrOr{MOUNT BRACKET
MAINSHAFTSUA.ASSEMBLY
'RAI{SMTSSTO HOUS|IGGASKETRgolace.
REVERSE GCAR COLLAR
]{EEDLE BEARII{G
NEVERSE GEAR
LOCT WASHEFReplace.
SHIFT FORX
REVERSE SEL€CTON
COUI{TERS}IAFTSUB-ASSEMEI.Y
DIFFEFEI{IIALASSEMBIY
(-t\
14-112

NOTE:
a Clean all parts thoroughly in solvent o. carburetor
cleaner and d.y with compressed air.a Blow out all passages.
a When removing the transmission housing, replace the
following:. Transmission housing gasket. Lock washer
1. Remove the transmission mount b.acket.
Remove the transmission housing mounting bolts
and hanger.
Align the spring pin of the control shaft with the
transmission housing groove by turning the control
shaft.
Install the special tool on the transmission housing,
then remove the housing as shown.
HOUSING PUI-LER07HAC-PK4010A
2.
4.
6.
Remove the countershaft reverse gear with the col-
lar and needle bearing.
Remove the lock bolt securing the shitt fork. then
remove the fork with the reverse selector trom the
countershatt.
Remove the countershaft and mainshaft sub-
assembly together.
8. Remove the ditferential assemblv.
14-113