Valve clearance HONDA INTEGRA 1994 4.G Workshop Manual

Standards and Service Limits
Cylinder Head/Valve Train (B188t enginelSecti6
*: Measured between the camshaft and rocker arm.
NH: NIHON HATSUJO manufactur€d valve spring
CH: CHUO HATSUJO manufacturod valve sDrino
- Declron
MEASUREMENTSTANDARD {NEWI '
SERVICE LIMIT
Compression250 rpm and wide open th.ottl€ Nominal
kPa (kgflcm?, psi) Minimum
Maximum variation
1,370 (14.0, 199)
930 (9.5, 140)
200 t2.0,2a)
Cylinder h.adW6rpage
Heightr31.95- 132.05 (5.195 - 5.199)
0.05 (0.002)
CamshaftEnd play
Camshaft-to-holder oil clearance
Total runout
Cam lobe height tN
EX
0.05 - 0.15 (0.002 - 0.0061
0.030 - 0.069 10.0012 - 0.0027)
0.03 (0.001) max.
33.7 16 11 .327 1l
33.528 (1.3200)
0.5 (0.02)
0.1s {0.006)
0.04 (0.002)
Valve clearance (Cold)* lN
EX
Valve stem O.D. tN
EX
Stem-to-guide clearance lN
EX
0.08 - 0.12 {0.003 - 0.005)
0.'r 6 - 0.20 (0.006 - 0.008)
6.580 - 6.590 (0.2591 - 0.2594)
6.550 - 6.s60 (0.2579 - 0.2583)
0.02 - 0.0s (0.001 - 0.002)
0.05 - 0.08 (0.002 - 0.003)
6.s5 (0.258)
6.52 (0.257)
0.0810.003)
0.11 (0.004)
width tN
EX
Stem instslled height tN
EX
r.25 - 1.55 (0.049 - 0.061)
1.25 - 1.55 {0.049 - 0.061)
40.765 - 41.235 (1.6049 - 1.6234)
12.763 - 43.235 t1,6a37 - 1.7022)
2.0 t0.08)
2.0 (0.08)
41.485 (1.6333)
43.485 (1.7120)
Valve springFree length {Reference} lN
EX NH
CH
42.36 (1.668)
47.09 {1.854}
47.08 (1.854)
41.s6 {1.636)
46.27 tl.A22l
46.21 l1.a22l
Valv6 guideLu. lN
EX
Installed height lN
6.61 - 6.63 (0.260 - 0.261)
6.61 - 6.6s (0.260- 0.261)
13.75 - 14.25 {0.541 - 0.561}
r5.75 - 16.25 10.620 - 0.640)
6.65 (0.262)
6.6510.2621
3-2

Standards and Service Limits
Cylander Head/Valve Train (B18Cl enginelSection 6
': M€asured betwoon the camshatt and rcc(er srm.
NH: NIHON HATSUJO manufacture v6lve spring
CH: CHUO HATSUJO manufscturo v6lve spring
MEASUBEMENTSTA]TDARD INEWISERV|C€ UM|T
Compr€6sion250 rpm and wide op€n throttle Nomin6l
kPa lkgl/cmr, psi) Minimum
Maximum variation
1,860 (19.0, 270)
930 (9.s, 140)
200 t2.o,2a)
Cylind6r hoadWarpage
H6ight'r41.95 - 1C2.05 (5.s89 - 5.593)
0.05 {0.002)
C.mshsftEnd play
Camshaft-to-holdsr oil clearance
Total runout
Cam lobo height lN Primery
Mid
Socondary
EX Primary
Mid
Secondary
0.05 - 0.1s (0.002 - 0.006)
0.050 - 0.089 (0.0020 - 0.0035)
0.015 (0.0006) max.
33.411{1.3154)
36.377 tl.13221
34.547 (1.3601)
33.1110.3036)
35.72011.4063)
34.381 {1.3536)
0.5 (0.02)
0.15 {0.006)
0.03 (0.001)
Valvo clorrance lcoldl* lN
EX
Valve stem O.D. lN
EX
Stom-to-guid6 clerrsnco lN
EX
0.15 - 0.19 {0.006 - 0.007}
0.17 - 0.21 (0.007 - 0.008)
5.475 - 5.48s (0.2156 - 0.21591
5.450 - 5.460 (0.2146 - 0.21s0'
0.025 - 0.055 {0.00'10 - 0.0022}
0.050 - 0.080 (0.0020 - 0.0031)
5.11510.21441
s.420 {0.2134)
0.08 10.003)
0.11{0.(x)4)
Valvo seatWidth tN
EX
Sr6m installed h€ight lN
EX
1.25 - 't.5s (0.049 - 0.06't)'1.25 - 1.s5 {0.049 - 0.061)
37.465 - 37.935 ('1.4750 - 1.4935)
37.16s - 37.635 t1.4632 - 1.4817)
2.0 (0.08)
2.0 (0.08)
38.185 (1.5033)
37.885 (1.491s)
Valv€ BpringFre6length (Roferenca) lN Outer
Inner NH
CH
EX NH
CH
41.05 (r.6161
36.'16 {1.4241
36.19 t1.425)
41.96 (1.652)
41.94 {1.651)
40.26 (1.585)
35.30 (1.390)
35.30 (1.390)
40.95 (1.612)
40.95 (1.612)
Valve guidol.D. tN
EX
Instslled hoight lN
EX
5.51 - 5.53 (0.217 - 0.218)
5.5r - 5.53 {0.2r7 - 0.218)
12.55 - r3.0s (0.494 - 0.514)
12.55 - 13.05 (0.494 - 0.s14t
5.55 (0.219)
5.5s {0.219}
Rock€r ermArm-to-shaft clearance lN
EX
0.025 - 0.0s2 {0.0010 - 0.0020)
0.025 - 0.0s2 (0.0010 - 0.0020)
0.08 (0.003)
0.08 (0.003)
3-4

Standards and Service Limits
Engine Lubrication - Section g
Cooling - Section t0
ng the coolant in the reservoir and that remaining in the engine.
eclton u _
MEASUREMENTSTANDARD INEW}SERVICE LIMTT
g talter
tiher
g filter
Engine oilCapacity etaet engine
f (US qt, lmp qt)
818C1 engine
Inner-to-outer rotor clearance
Pump horising-to-outer rotor clearance
Pump housing-to,rotor axial clearance
rressure setting at engine oil temp. 176.F {gO.Ct
kPa lkgtcm,, psi) At idte
At 3,000 rpm
4.6 {4.9, 4.0}tor engine overhaul
3.8 (4.0, 3.3) for oil change, inctudin
3.513.7, 3.11 for oil change, without
4.8 {5.1, 4.2) for engine overhaul
4.0 (4.2, 3.5) lor oit change, includin
3.7 i3.9 3 3l fdr ^il .hi
Oil pump
0.04 - 0.16 (0.002 - 0.006)
0.10 - 0.19 (0.004 _ 0.007)
0.02 - 0.07 (0.001 , 0.003)
0.20 (0.008)
0.21 (0.008)
0.1s (0.006)
Relief valve
70 (0.7, 10) min.
3{0 {3.5,50) min.
MEASUBEMENTSTANDARD INEWI
RadialorCoolant capacity I {US qt, lmp
I Including engine, heater, I
I cooling line and reservoir I
Reservoir capacity:
0.61 (0.63 US qt,0.53 tmp qt)
q0 81881 engine
818C1 engine
Opening pressure kPa (kgf/cm?, psi)
start to open oF (.C)
Fully open .F (.C)
Valve lift at fully open
lhermoswitch "ON" temperature .F {oC)
Thermoswitch "OFF" temporature "F (.C)
M/T: 6.4 (6.8, 5.6)tor overhaul
4.4 (4.6.3.9) f6r s66lsn1gh66q.*
A,rf: 6.7 {7.1, 5.9) for overhaul
4.7 {5.0, 4.1) for coolant chanoe*
M/T: 6.7 {7.1, 5.9} for overhaul
4.7 {5.0, 4.1) for coolant chanoe*
,3 - 113 toss - trs, r3= Jt&
-
196 - 203 (91 - 95)
Subtract 5 - 14 (3 - 8) from actuat -ON',
169 - 176
194 (90,
8.0 (0.31)
{76 80}
temperature
Radiator cap
Thermostst
Cooling fan
3-6

Standards and Service Limits
Differential (Manual transmissionlSection 15
Differential (Automatic transmissionlSection 15
Steering - Section 17
' When using a new belt, adjust detlection or tension to new values. Run the engine lor 5 minutes then turn it off.Readiust detlection or tension to used belt values.
M€ASUREMENTSTANDARD INEW) SERVICE LIMIT
DifferentialPinion shaft contact area LD. 81881 engine818C1 engineCarrier'to-pinion clearance 81881 engineB18C t engineDriveshafvintermediate shaft contact area LD.81881 engine818C1 engineCarrier to driveshaft clearance 81881 engineBlSC'l engineCarrier-to-intermediate shatt clearanceB188l engine818C1 engine
18.000 - 18.016 (0.7087 - 0.7093)18.000 18.018 (0.7087 - 0.7094)0.0r3 0.045 (0.0005 - 0.0018)0.0'13 - 0.047 (0.0005 0.0019)
28.000 - 28.021 \1.1024-1.1032128.005 - 28.025 (1.1026 1.'1033)0.020 - 0.062 (0.0008 0.0024)0.045 , 0.086 {0.0018 - 0.0034)
0.050 - 0.087 (0.0020 0.0034)0.075 - 0.111 (0.0030 - 0.0044)
o. t aron,0.1 {0.006}
Differentialprnron gearEacklasht. D.Pinion geaFto-pinion shaft clearance
0.05 0.15 (0.002 0.006)'18.042 - 18.066 (0.7103 0.7113)0.055 - 0.095 (0.0022 0.0037)
Adjust
0.15 {0.006)
Sel ring-to-bearing outer race clearance 81881 engin€0 - 0.10 (0 0.004)Adjust
Differential taper roller bearing preloadStarting torque N.m {kgfcm, lbf.in) Bl8Cl engine2.1r - 3.04 {21.5 - 3 r.0, 13.0- 18.7)Adjust
MEASUREMENTSTANDARO INEWISERVICE LIM]T
Difterentialcarfl€rPinion shatt contact area l.D.Carrier-to-oinion clearanceDriveshafvintermediate shaft contact are l.D.Carrier-to-driveshatt clearance
18.000 - 18.018 {0.7087 - 0.7094)0.016 - 0.052 {0.0006 - 0.0020)28.00s 28.025 {1.1026 - 1.1033)0.025 - 0.066 (0.0010 - 0.0026)
0.1 {0.004)
0.12 (0.005)
Differentialprnron gearBacklasht.D.Pinion gear-to-pinion shaft clearance
0.05 - 0.15 (0.002 - 0.006)18.042 - 18.066 (0.7r03 - 0.7113)0.059 - 0.095 (0.0023 - 0.0037)
Adjust
0.15 (0.006)
Set ring-to-bearing outer race clearance0 - 0.r5 (0 - 0.006)Adjust
MEASUREMENTSTANDARD INEWI
Steering wheelRotational play at steering wheel circumferenceStaning losd at steering wheel circumferenceN {kgf, lbfl Engine running
0 - 10 {0 - 0.39)
34 \3.5,7.71
GearboxAngle of rack-guide-screw loosened from lockedposition20" i 5'
PurnpPump pressure with shut-off valve closedkPa (kgtlcm,, psi)6,400 7.400 165 75. 920 - 1. r00)
Power steeringtluidRecommended fluidFluid capacity For overhaulf (US qt, lmp q0 For fluid change
Honda power steering fluid V1.06 (1.12,0.98)
0.79 (0.83,0.70)
Power steeringbelt*Deflection with 98 N (1okgt,22lhfl
between pulleys11.5- 13.5 (0.45 0.53)with used belt8.0 - 10.010.31 0.39)with new belt
Belt tension N lkgf, lbl)Measured with belt tension gauge390 - 540 (40 - 55, 88 - 120) with used belt740 880175 90. 170 200) with new belt

Design Specifications
]TEMMETRICENGLISHNOIES
:' vENSTONSOveralllength 3 DOOR
4 DOOR
Ov€rallWidth
Overall Height 3 DOOR
4 DOOR
Wheelbase 3 DOOR
4 DOOR
Track F/R
Ground Clearance
Seating Capacity
4.380 mm
4.525 mm
'1,710 mm
1,335 mm
1,370 mm
2,570 mm
2,620 mm
't,475/1,470 mm
150 mm
Four (3 DOOR)
172.1in
178.1 in
67.3 in
52.6 in
101.2 in
103.1 in
5|8.1/57.9 in
Five (4 DOOR)
,rerght (usA)cross V€hicle Weight Rating {GVWR)3,680lbs
'le,ght {CANADA)Gross Vehicls Weight Rating {GVWR)1,670 kg
:\GINEType81881 engine
818C1 engine
Cylinder Arrangement
Bore and Stroke
Displacement
Compression Ratio
81881
818C1
81881
B18C I
81881
B 18C1
81881
818C1
engrne
engane
engrne
engine
engine
engine
engine
engine
L!brication Systom
OilPump Displacement
Wster Pump Displacement
FuelRequired
81881
B18C 1
81881
B 18C1
91881
engrne
engrne
engine
engine
engine
818C1 engine
Water-cooled, 4-stroke DOHC
gasoline engine
Watercooled, 4-stroke DOHC
VTEC gasoline engine
Inline 4-cylinder, transverse
81.0 x 89.0 mm
81.0 x 87.2 mm
1,834 cm3 (mf )
1,797 cm3 (m{)
3.19 x 3.50 in
3.19 x 3.43 in
112 cu-in
110 cu-in
9.2:1
10.0 : 1
Eelt driven, OOHC 4 valve per cylinder
Belt driven, DOHC VTEC
4 valve per cylinder
Forced and wet sump, trochoid pump
50, {53 US qt, 44 lmp qt)/minute'l
71 f {75 US qt, 62 lmp qt)/minute"
140 f (148 US qt, 123 lmp qt)/minute*!
140 f (148 US qt. 123 lmp qt)/minute*'
UNLEADED gasoline with 86 Pump
Octane Numb€r or higher
Premium UNLEADED gasoline wilh
91 Pump Octane Number or higher
STARTERTypo
NormalOutput
NominalVoltage
Hour Rating
Direction of Rotation
Weight
Gear reduction
1.4 kW
12V
30 seconds
Clockwise as viewed lrom g6ar end
3.7 k9 | 8.3lbs
CLUTCHClutch Type
Clutch Facing Area
M/TSingle plate dry, diaphragm spring
Torq!e converter
203 cm' I 31 sq-in
TRANSMISSIONTransmission Type M/T
Primary Reduction
Synchronized 5-speed forward, 1 reverse
Electronically controlled
4-speed automatic. 1 rcverse
Diract 1 : 1
'1: At 6,000 engine
'2: At 7,600 engine
rpm
rpm
(cont'd)
3-17

Cylinder Head/Valve Train
81881 engine
Speciaf Tools .............6-2
Valve Clearance
Adiustment ............6-3
Valve Seals
Replacement (cylinder head
removal not required) ..................... 6-5
Reconditioning ......6-27
Timing gelt
lllustrated Index ............................... 6-7
Inspection .............. 6-9
Tension Adiustment ........................ 6-9
Removal .................6-10
Installation .............6-12
Crankshaft Pulley Bolt
Replacement .........6-8

6-3
Valve Clearance
Adjustment
NOTE:
. Valves should be adjusted cold; at a cylinder head
temperature of less than 100'F (38"C).
Adjustment is the same for both intake and exhaust
valves.
. After adjusting, retorque the crankshaft pulley bolt to
177 N.m (18.0 kgim, 130 lbf.ft).
1. Remove cylinder head cover.
ADJUSTING SCREW LOCATIONS:
2. Set the No. 1 piston at top dead center (TDC) (see
page 6-12). "UP" mark on the pulley should be at
the top, and the TDC grooves on the pulley should
align with the TDC groove on timing belt back
cover. TDC mark (painted white) on the crankshaft
pulley should align with pointer on the timing belt
tower cover.
Number 1 Diston at TDC:
INTAKE
EXHAUST
TDC MARKSlPeinted whitel
CRANKSHAFTPULLEY
"UP" MARKS
TDC GROOVES

Valve Clearance
Adjustment lcont'dl
a
4.
Adjust valve clearances on No. 1 cylinder.
lntlkc: 0.08 - o.l2 mm (o.(Xxl - 0.qr5 in)
Exhru3t 0.16 - 0.20 mm {0.0,05 - 0.008 in}
Loosen lhe locknut and turn the adjusting screw
until feeler gauge slides back and fonh with a slight
amount of drag.
LOCKNUT9x0.?5mm25 N.m 12,5 kgf.m, 18lbt'ft|
6.
Tighten the locknut and recheck clearance again.
Repeat adjustment if necessary.
Rotate ths crankshaft 180" counte.clockwise(camshaft pulley turns 90'). The "UP" mark should
be on the exhaust side. Adjust valves on No. 3 cylin-
der.
I{umbcr 3 pidon !t TDC:
EXHAUST CAITISHAFTPULI,IY
INTAKE CAMSHAFTPULLEY
.UP' MANKS
7. Rotate the crankshaft 180'counterclockwis€ to
bring No. 4 piston to TDC. The'UP" mark should
be pointing straight down. Adjust valves on No. 4
cylinder.
Numb€r il piston at TDC:
8. Rotate the crankshaft 180' co u nie rclockwise to
bring No. 2 piston to TDC. The "UP" mark should
be on the intake side. Adjust valves on No. 2 cylin-
oer.
Numbor 2 pirton !t TDC:
NOTE: Refer to page 6-31 when installing cylindor hEEd
cover.
"UP'MARKS
-UP" MARKS

Valves, Valve Springs and
Valve Seals
Valve lnstallation
When instaliing valves in the cylinder head, coat
valve stems with oil before insening them into valve
guides, and make sure valves move up and down
smoothlv.
When valves and springs are in place, lightly tap the
end of each valve stem two or three times to snsure
proper seating of valves and valve keepsrs (use plas-
tic mallet).
NOTE: Tap the valve stem only along its axis so you
do not bend the stem.
PLASNC MALI.IT
?ur
Valve Guides
Valve Movement
Measure the guide-to-stem clearance with a dial indica-
tor while rocking the stem in the direction of normal
thrust (wobble method).
lntake Valve Stsm-to-Guide Clearance:
Strndlrd (Newl: 0.0i1- 0.10 mm
(0.002 - 0.004 in)
Ssrvicc Limit: 0.16 mm {0.006 in)
Exhsust Valye Stom-to-Guide Clearance:
Standard {N€w): 0.10 - 0.16 mm
{0.0O'l - 0.006 in)
Slrvica Limit: 0.22 mm {0.000 in)
Valve extended 10 mm out from seat
lf measurement exceeds the service limit, recheck
using a new valve.
lf measurement is now within the service limit,
reassemble using a n€w valve.
lf measurement still exceeds limit, recheck using
alternate method below. then replace valve and
guide, if necessary.
NOTE: An alternate method of checking guide to stem
clearance is to subtract the O.D. of the valve stem, mea-
sured with a micrometer. from the l.D. of the valve
guide, measured with an inside micrometer or ball
gauge.
Take the measurements in three places along the valve
stem and three places inside the valve guide.
The diiference between the largest guide measurement
and the smallest stem measurement should not exceed
the service limit
lntake Valve Stom-to-Guide Clearance:
Standard (Newl: 0.02 - 0.05 mm(0.001-0.002 in)
Service Limit 0.08 mm (0.003 in)
Exhaust Valve Stom.to.Guid€ Clearanco:
Standard (Newl: 0.05 - 0.08 mm(0.002 - 0.003 inl
Srrvico Limit 0.ll mm 10.00't inl
6-24

Valve Guides
Replacement {cont'd}
7. SliD a 6.5 mm {0.25 in) stsel washor and the correct
driver attachment over the end of the driver {The
washer will absorb some of the impact and extend
the life of the driver).
.,F-q-re
tt-T-IIttlDRVEn 6,5 mm t0.25 in) ATTACHMENT
WASHER
8, Install the new guide(s) from the camshaft side of
the head; drive each one in until the attachment
bottoms on the head. lf you have 8ll sixteen guides
to do, vou may have to reheat the head one or two
more I|mes.
Valv6 Guida Instsllod Hcight:
lntaks: 13.75 - 14.25 mm
(o.sal - 0.561 inl
Exhru3t: 15.75 - 16.25 mm
{0.620 - 0.640 in}
Reaming
NOTE: For new valve guides only.
Coat both reamer and valve guide with cutting oil.
Rotate the reamer clockwise the full length of the
valve guide bore.
Continue to rotate the reamet clockwise while
removing it from the bore.
Thoroughly wash the guide in detergent and water
to remove any cutting residue.
Check clearance with a valve (see page 6-24).
. Verify that the valve slides in the intake 8nd
exhaust valve guides without ex€rting pressure.
VALVE GUII'E REAMER, 6.6 MM
079E4 - 667ot0c
REAMER HANDLE
s