ECU HONDA PASSPORT 2002 2.G User Guide

Driver and Passenger Safety30
To deactivate the locking
mechanism and remove a child
seat, unlatch the buckle, unroute
the seat belt, and let the belt fully
retract. Installing a Rear-Facing Child
Seat With the Lap Belt
To install a rear-facing child seat
in the center back seat with the
lap belt, follow instruction
number 1 on page 28 for routing
and latching the seat belt. Then
pull hard on the loose end of the belt to remove any slack (it may
help to put weight on the child
seat while pulling on the belt).
Finally, follow instruction number
5 on page 29 to verify that the
child seat is secure.

Driver and Passenger Safety32
child with enough force to cause
very serious or fatal injuries. If a
small child must be closely
watched, we recommend that
another adult sit in the back seat
with the child.
Improperly placing a
forward-facing child seat in the
front seat can result in serious
injury or death if the airbags
inflate.
If you must place a forward-
facing child seat in the front,
move the vehicle seat as far
back as possible and properly
restrain the child.
If it is necessary to put a forward-
facing child seat in the front,move the vehicle seat as far to the
rear as possible, be sure the child
seat is firmly secured to the
vehicle, and that the child is
properly strapped in the seat.
Installing a Child Seat With a
Lap/Shoulder Belt
The lap/shoulder belts in the outer
back and front passenger seating
positions have a locking
mechanism that must be activated
to secure a child seat.
The following pages provide
instructions on how to secure a
forward-facing
child seat with this
type of seat belt.
If you have a child seat designed
to attach to the vehicle ’s LATCH
anchorage system, follow the
instructions on page 39. See page 34 for how to secure a
forward-facing child seat in the
center back seat with the lap belt.
1. With the child seat in the
desired seating position, route
the belt through the child seat
according to the seat maker ’s
instructions, then insert the
latch plate into the buckle.

Driver and Passenger Safety33
2. To activate the lockable retractor,slowly pull the shoulder part of
the belt all the way out until it
stops, then let the belt feed back
into the retractor (you might
hear a clicking noise as the belt
retracts).
3. After the belt has retracted, tug on it. If the belt is locked,
you will not be able to pull it
out. If you can pull the belt out, it is not locked and you
will need to repeat these steps.
4. After confirming that the belt
is locked, grab the shoulder
part of the belt near the buckle
and pull up to remove any
slack from the lap part of the
belt. Remember, if the lap part
of the belt is not tight, the
child seat will not be secure. It may help to put weight on the
child seat, or push on the back
of the seat, while pulling up
on the belt.
5. Push and pull the child seat
forward and from side to side
to verify that it is secure
enough to stay upright during
normal driving maneuvers. If
the child seat is not secure,

Driver and Passenger Safety34
unlatch the belt, allow it to
retract fully, then repeat these
steps.
To deactivate the locking
mechanism in order to remove a
child seat, unlatch the buckle,
unroute the seat belt, and let the
belt fully retract. Installing a Child Seat With the
Lap Belt
To install a forward-facing child
seat in the center back seat with
the lap belt, follow instruction
number 1 on page 32 for routing
and latching the seat belt. Then
pull hard on the loose end of the
belt to remove any slack (it may
help to put weight on the child
seat while pulling on the belt). Finally, follow instruction number
5 on page 33 to verify that the
child seat is secure.
Protecting Larger Children
When a child reaches the
recommended weight or height
limit for a forward-facing child
seat, the child should sit in one of
the outer back seats and wear a
lap/shoulder belt. The
lap/shoulder belt provides better
protection than the lap belt.
If a child is too short for the
shoulder part of the belt to fit
properly, we recommend that the
child use a booster seat until the
child is tall enough to use the seat
belt without a booster.

Driver and Passenger Safety 37
The back seat is the safest place
for a child of any age or size.
In addition, the passenger’s airbag
poses serious risks to children. If
the seat is too far forward, or the
child’s head is thrown forward
during a collision, or the child is
unrestrained or out of position, an
inflating airbag can kill or
seriously injure the child.
Of course, children vary widely.
And while age may be one
indicator of when a child can
safely ride in the front, there are
other important factors you should
consider. Physical Size – Physically, a child
must
be large enough for the
lap/shoulder belt to properly fit
over the hips, chest, and shoulder
(see page 13 and 36). If the seat
belt does not fit properly, the child
should not sit in the front.
Maturity – To safely ride in
front, a child must be able to
follow the rules, including sitting
properly, and wearing the seat belt
properly throughout a ride. If you decide that a child can
safely ride up front, be sure to:
•Carefully read the owner
’s
manual, and make sure you
understand all seat belt
instructions and all safety
information.
•Move the vehicle seat to the
rear-most position.
•Have the child sit up straight,
back against the seat, and feet
on or near the floor.
•Check that the child’ s seat belt
is properly positioned and
secured.
•Supervise the child. Even
mature children sometimes
need to be reminded to fasten
their seat belts or sit properly.

Driver and Passenger Safety38
Using Child Seats With
Tethers
REAR
FLOOR
ATTACHMENT POINTS
Your vehicle has two attachment
points in the rear floor for
securing a tether-style child seat
to the vehicle.
Since a tether can provide
additional security, we
recommend using a tether
whenever one is required or
available. Check with the child
seat maker to determine whether a
tether is available for a particular
child seat.
COVER LATCH
ANCHORAGE
POINT
The tether anchorage points are
located under plastic covers. Use
your finger to push the latch, then
pivot the cover backward to
access the anchorage point.
TETHER FROM
CHILD SEAT
Attach the tether strap hook to the
tether anchorage point as shown
in the illustration, then tighten the
strap according to the child seat
maker ’ s instructions.

Driver and Passenger Safety39
Using LATCH
LOWER
ANCHORAGES
Your vehicle is equipped with
LATCH (Lower Anchorages and
Tethers for Children) at the outer
rear seats. The lower anchors
anchorages are located between
the seat-back and the seat bottom,
and are to be used only with a
child seat designed for use with
LATCH.
To install a LATCH-compatible
child seat:
1. Move the seat belt buckle or
center seat belt away from the
lower anchors.
2. Make sure there are no foreign objects around the anchors.
Foreign objects could get in
the way of a secure connection
between the child seat and the
anchor.
RIGID TYPE
3. Put the child seat in the rear
left or right vehicle seat and
attach the child seat to the
lower anchor according to the
child seat maker ’s
instructions.

Driver and Passenger Safety40
FLEXIBLE TYPE
4. Follow the child seat maker’s
instructions for any additional
advice on adjusting or
tightening the fit.
CHILD
SEAT
TETHER
COVER
ANCHORAGE
POINT
5. Attach the tether strap hook to the tether anchorage point and
tighten the strap according to
the child seat maker ’s
instructions. 6. Push and pull the child seat
forward and from side to side
to verify that it is secure
enough to stay upright during
normal driving maneuvers.

42 Driver and Passenger Safety
All the lap/shoulder belts except
the driver’s have an additional
locking mechanism that must be
activated to secure a child seat.
(See pages 27 and 32 for
instructions on how to secure
child seats with this type of seat
belt.)
If the shoulder part of the belt is
pulled all the way out, the locking
mechanism will activate. The belt
will retract, but it will not allow a
passenger to move freely.
To deactivate the locking
mechanism, unlatch the buckle
and let the seat belt fully retract.
To refasten the belt, pull it out
only as far as needed.
See page 13 for instructions on
how to wear the lap/shoulder belt
properly.
Lap
Belt
The lap belt has one manually
adjusted belt that fits across the
hips.
To fasten the belt, insert the latch
plate into the buckle marked
CENTER, then tug on the belt to
make sure the buckle is latched.
To unlock the belt, push the red
PRESS button. See page 14 for how to lengthen
the lap belt, and how to properly
position the belt.
Seat Belt Maintenance
For safety, you should check the
condition of your seat belts
regularly.
Pull each belt out fully and look
for frays, cuts, burns, and wear.
Check that the latches work
smoothly and that the lap/shoulder
belts retract easily. Any belt not in
good condition or not working
properly will not provide good
protection and should be replaced
as soon as possible.

81Instruments and Controls
Shifting the Transfer Control
Lever
4H
↔ 4L: Stop the vehicle. Place
the transmission lever in
“N” (Neutral) position.
Then move the transfer
control lever from 4H to
4L, or 4L to 4H.
Move the transfer control lever
quickly and securely between
positions. Do not stop midway.
The transfer gear box can be
damaged if the control lever is not
firmly in gear. Some noise is
normal when shifting.
Always stop the vehicle before
shifting between low and high
range (4H
4L or 4L
4H).
If the 4WD indicator continues to
blink rapidly, it indicates that the
system was shifted out of
sequence. Stop the vehicle, select
4WD with the 4WD-2WD switch, shift the lever from 4L to 4H, then
select 2WD. Drive in a straight
line to reset the system. If the
indicator continues to blink, see
your Honda dealer.
Do not use 4-wheel drive for
driving on dry pavement. This
causes noise and wear, and taking
tight turns can damage the
transfer case and driveshafts. It
also reduces fuel economy.
Be careful that you do not exceed
the following maximum allowable
speeds when accelerating.
mph (km/h)
RangeAutomatic TransmissionRange“L”“2”“3”
“2H”35 (56)65
(105)–
“4H”35 (56)65
(105)65
(105)
“4L”15 (24)30 (48)50 (81)
Driving Pattern Selector
You can select a driving pattern
suitable for existing driving
conditions.
When neither “POWER” nor
“
WINTER” lights are illuminated,
the normal driving program for
general driving conditions is
operative.